ps600.h

在Ｕｎｉｘ平台下完成的电力系统广发使用的ＩＥＣ１０３规约的程序

EVTALM  PSL_B8_Event[]={
{0xFF,   0,   0,   "未定义信号"},
{0x50,   0,   0,   "高频保护初始化"},
{0x51,   0,   0,   "RAM错误"},
{0x52,   0,   0,   "EPROM错误"},
{0x53,   0,   0,   "内容错误"},
{0x54,   0,   0,   "EEPROM错误"},
{0x55,   0,   0,   "定值区无效"},
{0x56,   0,   0,   "定值校验错误"},
{0x57,   0,   0,   "开入异常"},
{0x58,   0,   0,   "开出异常"},
{0x59,   0,   0,   "AD错误"},
{0x5A,   0,   0,   "内部电源偏低"},
{0x5B,   0,   0,   "零漂越限"},
{0x5C,   0,   0,   "PT断线"},
{0x5D,   0,   0,   "PT三相失压"},
{0x5E,   0,   0,   "PT反序"},
{0x5F,   0,   0,   "CT断线"},
{0x60,   0,   0,   "CT不平衡"},
{0x61,   0,   0,   "CT反序"},
{0x62,   0,   0,   "负载不对称"},
{0x63,   0,   0,   "高频通道异常"},
{0x64,   0,   0,   "高频跳位继异常"},
{0x65,   0,   0,   "保护动作开入异常"},
{0x66,   0,   0,   "长期过电流"},
{0x67,   0,   0,   "高频过负荷告警"},
{0x00,   0,   0,   "高频保护A跳出口"},
{0x01,   0,   0,   "高频保护B跳出口"},
{0x02,   0,   0,   "高频保护C跳出口"},
{0x03,   0,   0,   "高频保护单跳失败"},
{0x04,   0,   0,   "高频保护三跳出口"},
{0x05,   0,   0,   "高频保护三跳失败"},
{0x06,   0,   0,   "高频保护永跳出口"},
{0x07,   0,   0,   "高频保护永跳失败"},
{0x08,   0,   0,   "高频永跳失败返回"},
{0x09,   0,   0,   "高频距离加速永跳"},
{0x0A,   0,   0,   "高频无选相三跳"},
{0x0B,   0,   0,   "高频保护启动"},
{0x0C,   0,   0,   "高频保护整组复归"},
{0x0D,   0,   0,   "高频长期不能复归"},
{0xB0,   0,   0,   "A相跳位继电器"},
{0xB1,   0,   0,   "B相跳位继电器"},
{0xB2,   0,   0,   "C相跳位继电器"},
{0xB3,   0,   0,   "高频压板"},
{0xB4,   0,   0,   "收信输入"},
{0xB5,   0,   0,   "通道试验"},
{0xB6,   0,   0,   "A相跳闸反馈"},
{0xB7,   0,   0,   "B相跳闸反馈"},
{0xB8,   0,   0,   "C相跳闸反馈"},
{0xB9,   0,   0,   "三跳反馈"},
{0xBA,   0,   0,   "永跳反馈"},
{0xBB,   0,   0,   "重合闸反馈"},
{0xBC,   0,   0,   "重合闸方式2"},
{0xBD,   0,   0,   "其他保护动作"},
{0xBE,   0,   0,   "导频消失"},
{0xBF,   0,   0,   "收发讯机告警"},
{0xC0,   0,   0,   "禁止整组复归"},
{0xC1,   0,   0,   "GPS对时"},
{0xC2,   0,   0,   "遥合反馈"},
{0xC3,   0,   0,   "遥跳反馈"},
{0xC4,   0,   0,   "事故总信号"},
{0xC5,   0,   0,   "告警总信号"},
{0xA0,   0,   0,   "高频投入压板"},
};

/*
EVTALM  PSL_B8_Event[]={
{0x00,   0,   0,   "未定义信号"},
{0x50,   0,   0,   "后备保护初始化"},
{0x51,   0,   0,   "RAM错误"},
{0x52,   0,   0,   "EPROM错误"},
{0x53,   0,   0,   "闪存错误"},
{0x54,   0,   0,   "EEPROM错误"},
{0x55,   0,   0,   "定值区无效"},
{0x56,   0,   0,   "定值校验错误"},
{0x57,   0,   0,   "开入异常"},
{0x58,   0,   0,   "开出异常"},
{0x59,   0,   0,   "AD错误"},
{0x5A,   0,   0,   "内部电源偏低"},
{0x5B,   0,   0,   "零漂越限"},
{0x5C,   0,   0,   "PT断线"},
{0x5D,   0,   0,   "PT三相失压"},
{0x5E,   0,   0,   "PT反序"},
{0x5F,   0,   0,   "CT断线"},
{0x60,   0,   0,   "CT不平衡"},
{0x61,   0,   0,   "CT反序"},
{0x62,   0,   0,   "负载不对称"},
{0x63,   0,   0,   "距离过负荷告警"},
{0x64,   0,   0,   "跳位继电器异常"},
{0x65,   0,   0,   "长期过电流"},
{0x00,   0,   0,   "快速距离动作"},
{0x01,   0,   0,   "相间距离I段动作"},
{0x02,   0,   0,   "相间距离II段动作"},
{0x03,   0,   0,   "相间距离III段动作"},
{0x04,   0,   0,   "接地距离I段动作"},
{0x05,   0,   0,   "接地距离II段动作"},
{0x06,   0,   0,   "接地距离III段动作"},
{0x07,   0,   0,   "距离重合加速动作"},
{0x08,   0,   0,   "距离手合加速动作"},
{0x09,   0,   0,   "零序I段动作"},
{0x0A,   0,   0,   "零序II段动作"},
{0x0B,   0,   0,   "零序III段动作"},
{0x0C,   0,   0,   "零序IV段动作"},
{0x0D,   0,   0,   "零序加速段动作"},
{0x0E,   0,   0,   "PT断线零序段动作"},
{0x0F,   0,   0,   "PT断线相过流动作"},
{0x10,   0,   0,   "保护A跳出口"},
{0x11,   0,   0,   "保护B跳出口"},
{0x12,   0,   0,   "保护C跳出口"},
{0x13,   0,   0,   "保护三跳出口"},
{0x14,   0,   0,   "保护永跳出口"},
{0x15,   0,   0,   "保护单跳失败"},
{0x16,   0,   0,   "保护三跳失败"},
{0x17,   0,   0,   "保护永跳失败"},
{0x18,   0,   0,   "保护永跳失败返回"},
{0x19,   0,   0,   "无选相后备跳闸"},
{0x1A,   0,   0,   "故障类型和测距"},
{0x1B,   0,   0,   "零序反时限动作"},
{0x1C,   0,   0,   "距离零序保护启动"},
{0x1D,   0,   0,   "距离零序保护复归"},
{0x1E,   0,   0,   "测距阻抗值"},
{0x1F,   0,   0,   "故障相电流"},
{0x20,   0,   0,   "后备长期不能复归"},
{0xB0,   0,   0,   "A相跳位继电器"},
{0xB1,   0,   0,   "B相跳位继电器"},
{0xB2,   0,   0,   "C相跳位继电器"},
{0xB3,   0,   0,   "相间距离压板"},
{0xB4,   0,   0,   "接地距离压板"},
{0xB5,   0,   0,   "零序I段压板"},
{0xB6,   0,   0,   "零序II段压板"},
{0xB7,   0,   0,   "零序总投压板"},
{0xB8,   0,   0,   "A相跳闸反馈"},
{0xB9,   0,   0,   "B相跳闸反馈"},
{0xBA,   0,   0,   "C相跳闸反馈"},
{0xBB,   0,   0,   "三跳反馈"},
{0xBC,   0,   0,   "永跳反馈"},
{0xBD,   0,   0,   "重合闸方式2"},
{0xBE,   0,   0,   "重合闸反馈"},
{0xBF,   0,   0,   "GPS对时"},
{0xC0,   0,   0,   "禁止整组复归"},
{0xC1,   0,   0,   "遥合反馈"},
{0xC2,   0,   0,   "遥跳反馈"},
{0xC3,   0,   0,   "事故总信号"},
{0xC4,   0,   0,   "告警总信号"},
{0xA0,   0,   0,   "相间距离压板"},
{0xA1,   0,   0,   "接地距离压板"},
{0xA2,   0,   0,   "零序I段压板"},
{0xA3,   0,   0,   "零序II段压板"},
{0xA4,   0,   0,   "零序总投压板"},
};

EVTALM  PSL_B8_Event[]={
{0x00,   0,   0,   "未定义信号"},
{0x50,   0,   0,   "重合闸初始化"},
{0x51,   0,   0,   "RAM错误"},
{0x52,   0,   0,   "EPROM错误"},
{0x53,   0,   0,   "闪存错误"},
{0x54,   0,   0,   "EEPROM错误"},
{0x55,   0,   0,   "定值区无效"},
{0x56,   0,   0,   "定值校验错误"},
{0x57,   0,   0,   "开入异常"},
{0x58,   0,   0,   "开出异常"},
{0x59,   0,   0,   "AD错误"},
{0x5A,   0,   0,   "内部电源偏低"},
{0x5B,   0,   0,   "零漂越限"},
{0x5C,   0,   0,   "PT断线"},
{0x5D,   0,   0,   "PT三相失压"},
{0x5E,   0,   0,   "PT反序"},
{0x5F,   0,   0,   "CT断线"},
{0x60,   0,   0,   "CT不平衡"},
{0x61,   0,   0,   "CT反序"},
{0x62,   0,   0,   "负载不对称"},
{0x63,   0,   0,   "跳位继电器异常"},
{0x64,   0,   0,   "跳闸反馈异常"},
{0x65,   0,   0,   "综重低气压开入"},
{0x00,   0,   0,   "综重电流启动"},
{0x01,   0,   0,   "综重电流复归"},
{0x02,   0,   0,   "综重重合闸启动"},
{0x03,   0,   0,   "综重重合闸复归"},
{0x04,   0,   0,   "综重重合闸出口"},
{0x05,   0,   0,   "综重沟通三跳"},
{0x06,   0,   0,   "综重永跳出口"},
{0x07,   0,   0,   "综重三跳失败"},
{0x08,   0,   0,   "综重永跳失败"},
{0x09,   0,   0,   "综重永跳失败返回"},
{0x0A,   0,   0,   "综重长期不能复归"},
{0xB0,   0,   0,   "A相跳位继电器"},
{0xB1,   0,   0,   "B相跳位继电器"},
{0xB2,   0,   0,   "C相跳位继电器"},
{0xB3,   0,   0,   "A相跳闸反馈"},
{0xB4,   0,   0,   "B相跳闸反馈"},
{0xB5,   0,   0,   "C相跳闸反馈"},
{0xB6,   0,   0,   "三跳反馈"},
{0xB7,   0,   0,   "永跳反馈"},
{0xB8,   0,   0,   "重合闸反馈"},
{0xB9,   0,   0,   "重合闸方式1"},
{0xBA,   0,   0,   "重合闸方式2"},
{0xBB,   0,   0,   "GPS对时"},
{0xBC,   0,   0,   "禁止整组复归"},
{0xBD,   0,   0,   "遥合反馈"},
{0xBE,   0,   0,   "遥跳反馈"},
{0xBF,   0,   0,   "单跳启动重合闸"},
{0xC0,   0,   0,   "三跳启动重合闸"},
{0xC1,   0,   0,   "闭锁重合闸"},
{0xC2,   0,   0,   "低气压闭锁重合闸"},
{0xC3,   0,   0,   "重合闸时间控制"},
{0xC4,   0,   0,   "手动准同期"},
{0xC5,   0,   0,   "事故总信号"},
{0xC6,   0,   0,   "告警总信号"},
{0xA0,   0,   0,   "重合闸方式1"},
{0xA1,   0,   0,   "重合闸方式2"},
};
*/