udc.h

操作系统SunOS 4.1.3版本的源码

/* @(#)udc.h 1.1 92/07/30 SMI */
/*
 * Copyright (c) 1989 by Sun Microsystems, Inc.
 */

#ifndef	_scsi_adapters_udc_h
#define	_scsi_adapters_udc_h

/*
 * AMD 9516 UDC (Universal DMA Controller) Registers.
 *
 * Used for the Sun3/50 and Sun3/60 SCSI interfaces only.
 */

/*
 * addresses of the udc registers accessed directly by driver
 */

#define	UDC_ADR_MODE		0x38	/* master mode register */
#define	UDC_ADR_COMMAND		0x2e	/* command register (write only) */
#define	UDC_ADR_STATUS		0x2e	/* status register (read only) */
#define	UDC_ADR_CAR_HIGH	0x26	/* chain addr reg, high word */
#define	UDC_ADR_CAR_LOW		0x22	/* chain addr reg, low word */
#define	UDC_ADR_CARA_HIGH	0x1a	/* cur addr reg A, high word */
#define	UDC_ADR_CARA_LOW	0x0a	/* cur addr reg A, low word */
#define	UDC_ADR_CARB_HIGH	0x12	/* cur addr reg B, high word */
#define	UDC_ADR_CARB_LOW	0x02	/* cur addr reg B, low word */
#define	UDC_ADR_CMR_HIGH	0x56	/* channel mode reg, high word */
#define	UDC_ADR_CMR_LOW		0x52	/* channel mode reg, low word */
#define	UDC_ADR_COUNT		0x32	/* number of words to transfer */

/*
 * For a dma transfer, the appropriate udc registers are loaded from a
 * table in memory pointed to by the chain address register.
 */
struct udc_table {
	u_short			rsel;	/* tells udc which regs to load */
	u_short			haddr;	/* high word of main mem dma address */
	u_short			laddr;	/* low word of main mem dma address */
	u_short			count;	/* num words to transfer */
	u_short			hcmr;	/* high word of channel mode reg */
	u_short			lcmr;	/* low word of channel mode reg */
};

/*
 * indicates which udc registers are to be set based on info in above table
 */

#define	UDC_RSEL_RECV		0x0182
#define	UDC_RSEL_SEND		0x0282

/*
 * setting of chain mode reg: selects how the dma op is to be executed
 */

#define	UDC_CMR_HIGH		0x0040	/* high word of channel mode reg */
#define	UDC_CMR_LSEND		0x00c2	/* low word of cmr when send */
#define	UDC_CMR_LRECV		0x00d2	/* low word of cmr when receiving */

/*
 * setting for the master mode register
 */

#define	UDC_MODE		0xd	/* enables udc chip */

/*
 * setting for the low byte in the high word of an address
 */

#define	UDC_ADDR_INFO		0x40	/* inc addr after each word is dma'd */

/*
 * udc commands
 */

#define	UDC_CMD_STRT_CHN	0xa0	/* start chaining */
#define	UDC_CMD_CIE		0x32	/* channel 1 interrupt enable */
#define	UDC_CMD_RESET		0x00	/* reset udc, same as hdw reset */

/*
 * bits in the udc status register
 */

#define	UDC_SR_CIE		0x8000	/* channel interrupt enable */
#define	UDC_SR_IP		0x2000	/* interrupt pending */
#define	UDC_SR_CA		0x1000	/* channel abort */
#define	UDC_SR_NAC		0x0800	/* no auto reload or chaining*/
#define	UDC_SR_WFB		0x0400	/* waiting for bus */
#define	UDC_SR_NCRP		0x0200	/* second interrupt pending */
#define	UDC_SR_HM		0x0040	/* hardware mask */
#define	UDC_SR_HRQ		0x0020	/* hardware request */
#define	UDC_SR_MCH		0x0010	/* match on upper comparator byte */
#define	UDC_SR_MCL		0x0008	/* match on lower comparator byte */
#define	UDC_SR_MC		0x0004	/* match condition ended dma */
#define	UDC_SR_EOP		0x0002	/* eop condition ended dma */
#define	UDC_SR_TC		0x0001	/* termination of count ended dma */

#endif	/* !_scsi_adapters_udc_h */