changelog

来自「eCos/RedBoot for勤研ARM AnywhereII(4510) 含」· 代码 · 共 1,522 行 · 第 1/4 页

	The contents of individual source files are unchanged; they build
	in just the same emvironment except for a very few cases where the
	config file name changed in this movement.

	Targets in ecos.db have been redefined to bring in all relevant
	hardware packages including net and serial drivers (but the newly
	included packages are only active if their desired parent is
	available.)
	
	The names of CDL options (and their #defines of course) stay the
	same for the serial drivers, for backward compatibility.

	* templates/*/current.ect: these have had CYGPKG_IO_SERIAL added
	rather than it being in (almost) all target definitions.
	
2000-04-07  Jonathan Larmour  <[e-mail]>

	* src/common/tty.c (tty_read): Correct handling of modes with newlines

2000-04-05  Jonathan Larmour  <[e-mail]>

	* src/common/tty.c (tty_read): CRLF conversion should use \r\n not \n\r
	(tty_write): Similarly

	* include/ttyio.h: Update CYG_TTY_IN_FLAGS_CRLF and
	CYG_TTY_IN_FLAGS_CRLF to match

2000-03-31  Jesper Skov  <[e-mail]>

	* cdl/ser_sh_edk7708.cdl: Limit legal baud rate range.
	* src/sh/sh_sci_serial.c: Use baud rate macro instead of hardwired
	constants.

2000-03-28  John Dallaway  <[e-mail]>

	* cdl/io_serial.cdl,
	  cdl/ser_arm_aeb.cdl,
	  cdl/ser_arm_cma230.cdl,
	  cdl/ser_arm_edb7xxx.cdl,
	  cdl/ser_arm_pid.cdl,
	  cdl/ser_i386_pc.cdl,
	  cdl/ser_mips_jmr3904.cdl,
	  cdl/ser_mips_vrc4373.cdl,
	  cdl/ser_mn10300.cdl,
	  cdl/ser_powerpc_cogent.cdl,
	  cdl/ser_quicc_smc.cdl,
	  cdl/ser_sh_edk7708.cdl,
	  cdl/ser_sparclite_sleb.cdl,
	  cdl/tty.cdl:

	Adjust documentation URLs.

2000-03-07  Jesper Skov  <[e-mail]>

	* cdl/ser_mips_jmr3904.cdl: Rename devices to match CDL naming.

2000-02-29  Jonathan Larmour  <[e-mail]>

	* include/serialio.h: Correct baud rate typo: 230400 rather than
	234000. Thanks to Grant Edwards for the report.

2000-02-28  Gary Thomas  <[e-mail]>

	* src/powerpc/quicc_smc_serial.c: Use standard 'diag_dump_buf()'.

2000-02-28  Jesper Skov  <[e-mail]>

	* tests/ser_test_protocol.inl: Allow 115200 baud on Cogent
	again. Fixed interrupt problem.

2000-02-22  Jesper Skov  <[e-mail]>

	* tests/ser_test_protocol.inl: Don't use 115200 baud on
	Cogent. Our slower boards can't keep up.

2000-02-17  Gary Thomas  <[e-mail]>

	* cdl/ser_powerpc_cogent.cdl: Fix incorrect dependency.

2000-02-16  Nick Garnett  <[e-mail]>

	* include/pkgconf/io_serial.h:
	Added configury for PC serial device drivers.

	* cdl/ser_i386_pc.cdl:
	* src/i386/pc_serial.c:
	* src/i386/pc_serial.h:
	Added these files to implement PC serial line drivers.

	* cdl/io_serial.cdl:
	Added CYGPKG_IO_SERIAL_I386_PC.

	* tests/ser_test_protocol.inl:
	Added support for PC serial line testing.
	
2000-02-11  Jesper Skov  <[e-mail]>

	* src/sh/sh_sci_7708.inl (DEVTAB_ENTRY): 
	* src/sparclite/sleb_sdtr.c: 
	serial_devio => cyg_io_serial_devio

2000-02-10  Jonathan Larmour  <[e-mail]>

	* src/mn10300/mn10300_serial.c: Ensure all CYG_HAL_MN10300_*
	preprocessor conditionals use the correct CYGPKG_HAL_MN10300_AM3* form
	now.	

2000-02-03  Jesper Skov  <[e-mail]>

	* src/powerpc/quicc_smc_serial.c: CYG_HAL_POWERPC_x->CYGPKG_...

2000-02-02  Jonathan Larmour  <[e-mail]>

	* src/arm/aeb_serial.h: Rename lower case register macros to REG_ upper
	case macros

	* src/arm/aeb_serial.c: Update to reflect above

2000-01-31 Simon FitzMaurice  <[e-mail]>
  * cdl/*.cdl:

  Adjust help URLs in line with new doc layout.
  
2000-01-28 Simon FitzMaurice  <[e-mail]>
  * cdl/*.cdl:

  Adjust help URLs in line with new doc layout.
  
2000-01-28  Gary Thomas  <[e-mail]>

	* src/common/tty.c (tty_read): Fix problem with backspace at start
	of line (size must be 'signed' for compare to work).

2000-01-19  Hugo Tyson  <[e-mail]>

	* cdl/*.cdl: Add descriptions to a number of options &c which were
	lacking same, also tidied up other typos as noticed en passant.

2000-01-17  Gary Thomas  <[e-mail]>

	* src/common/tty.c (tty_read): Avoid echoing "backspace/erase" at
	start of line.

2000-01-05  Gary Thomas  <[e-mail]>

	* src/common/serial.c (serial_write): Avoid potential deadlock if
	transmit start actually sends enough characters to signal cond wait.

2000-01-03  Gary Thomas  <[e-mail]>

	* include/serial.h: Fix namespace pollution - 
	serial_devio => cyg_io_serial_devio
	serial_callbacks => cyg_io_serial_callbacks

	* src/mips/tx3904_serial.c: 
	* src/mips/vrc4373_serial.c: 
	* src/mn10300/mn10300_serial.c: 
	* src/powerpc/quicc_smc_serial.c: 
	* src/powerpc/cogent_serial_with_ints.c: 
	* src/sparclite/sleb_sdtr.c: 
	* src/arm/aeb_serial.c: 
	* src/arm/pid_serial_with_ints.c: 
	* src/arm/edb7xxx_serial.c: 
	* src/arm/cma230_serial.c: 
	* src/arm/ebsa285_serial.c: 
	* src/common/haldiag.c: 
	* src/common/serial.c: Fix namespace pollution - 
	serial_devio => cyg_io_serial_devio

1999-12-06  Gary Thomas  <[e-mail]>

	* src/arm/pid_serial_with_ints.c (pid_serial_DSR): Add loop to handle
	case where an interrupt represents multiple events.

1999-11-19  Gary Thomas  <[e-mail]>

	* src/powerpc/quicc_smc_serial.c: Channel select for SMC2 was wrong.

1999-11-18  Gary Thomas  <[e-mail]>

	* include/pkgconf/io_serial.h: Remove mention of 7209/7212.

1999-11-03  John Dallaway  <[e-mail]>

	* cdl/io_serial.cdl: Define build options.

1999-10-26  Jesper Skov  <[e-mail]>
	* tests/serial5.c (serial_test): Reduce speed in thumb mode.

	* src/arm/pid_serial.h: Added BE support.

	* src/PKGconf.mak: Use CYGPKG_<> instead of CYG_<> to control what
	needs to be compiled.

1999-10-25  Gary Thomas  <[e-mail]>

	* src/arm/pid_serial.h (ISR_RxTO): Define - character received but
	not handled "promptly".

	* src/arm/pid_serial_with_ints.c (pid_serial_DSR): Handle rcv interrupts
	properly (can't ignore them even with TO bit set).

	* src/arm/cl7211_serial.c (cl7211_serial_rx_DSR): Need to handle all
	input (empty input FIFO) otherwise characters get dropped.

1999-10-15  Jesper Skov  <[e-mail]>

	* tests/ser_test_protocol.inl: Removed AEB rev C change. Was bogus.

1999-10-11  Nick Garnett  <[e-mail]>

	* tests/ser_test_protocol.inl: Added configury for VR4300 testing.

	* src/mips/vrc4373_serial.c: Added Bi-endian support.

	* include/pkgconf/io_serial.h: Adjusted default baud rates to
	38400.

1999-10-06  Jesper Skov  <[e-mail]>

	* tests/ser_test_protocol.inl: Run tests on AEB rev C as well.

1999-09-28  Hugo Tyson  <[e-mail]>

	* src/powerpc/quicc_smc_serial.c (quicc_smc_serial_init): Correct
	value supplied for interrupt priority - it may be unused, but it
	is asserted for range.  Initialize the diagnostic channel if on an
	MBX and if NOT using SMC1 ourselves, to ensure that diag output
	and built-in stubs work correctly; otherwise reset the quicc and
	ignore SMC1 as before.  Fix various warnings, mostly about
	casting/arg-passing/assigning away volatile.

1999-08-31  Jesper Skov  <[e-mail]>

	* tests/ser_test_protocol.inl: Define dummy crash ID.

1999-08-30  Jesper Skov  <[e-mail]>

	* tests/ser_test_protocol.inl: Added crash information which
	should help track down repeating errors.

1999-08-20  Jesper Skov  <[e-mail]>

	* tests/README: Added.

1999-08-18  Jesper Skov  <[e-mail]>

	* tests/tty1.c: 
	* tests/tty2.c: 
	* tests/serial1.c: 
	* tests/serial2.c: 
	* tests/serial3.c: 
	* tests/serial4.c: 
	* tests/serial5.c: 
	* tests/PKGconf.mak:
	Require kernel and kernel C API.
	
1999-08-17  Nick Garnett  <[e-mail]>

	* src/mn10300/mn10300_serial.c: Added a simple implementation of a
	receive FIFO to try and reduce the overhead of receiving bytes.

1999-08-16  Jonathan Larmour  <[e-mail]>

	* src/PKGconf.mak:
	* src/mn10300/mn10300_serial.c:
	* tests/ser_test_protocol.inl:
	Rename all am32 -> am31

1999-08-12  Nick Garnett  <[e-mail]>

	Imported following changes from development branch:
	
    1999-08-11  Nick Garnett  <[e-mail]>

	* tests/serial5.c: Modified config test for boards that need a lower
	speed for this test.

	* tests/ser_test_protocol.inl: Removed 14400 baud tests for all
	MN10300 variants. The MN10300 cannot currently do this speed.

	* src/mn10300/mn10300_serial.c: Tidied up the transmit interrupt
	enable/disable code to be variant specific.

	* include/pkgconf/io_serial.h: Undid Jonathan's change, since the
	same options are used for all MN10300 variants.
	
    1999-08-10  Jonathan Larmour  <[e-mail]>

	* include/pkgconf/io_serial.h:
        Reparent CYGPKG_IO_SERIAL_MN10300 from under CYGPKG_HAL_MN10300 to
        CYGPKG_HAL_MN10300_AM32_STDEVAL1 since it's stdeval1 specific

    1999-08-04  Nick Garnett  <[e-mail]>

	* tests/ser_test_protocol.inl:
	Changed names of MN10300 defines tested. Added AM33 definitions.

	* src/mn10300/mn10300_serial.c:
	Modified driver to work on am33 too. This simply requires some
	alternate definitions of things like register addresses and some
	bits in them plus some extra parameterization of some register
	values.

	* src/PKGconf.mak:
	Added am33 to list of architectures supporting serial lines.
	
1999-07-28  Gary Thomas  <[e-mail]>

	* include/pkgconf/io_serial.h: Update descriptions to be more
 	generic (CL7x11 instead of CL7211).

1999-07-28  Jonathan Larmour  <[e-mail]>

	* include/pkgconf/io_serial.h: Correct typos in CDL description
	for serial port 2 driver

1999-07-26  Hugo Tyson  <[e-mail]>

	* src/arm/ebsa285_serial.c: New file: device driver for the serial
	device of the Intel StrongARM EBSA-285 evaluation board.

	* include/pkgconf/io_serial.h (CYGPKG_IO_SERIAL_ARM_EBSA285):
	Config for it.

	* src/PKGconf.mak (EXTRAS_COMPILE): Compile it.

	* tests/ser_test_protocol.inl (TEST_SER_DEV): Enable testing of it.

1999-07-08  Jesper Skov  <[e-mail]>

	* tests/ser_test_protocol.inl (change_config): Changed implementation.

1999-06-27  Gary Thomas  <[e-mail]>

	* src/powerpc/quicc_smc_serial.c (quicc_smc_serial_init): More robust
	initialization, with data cache disabled.  This seems to fix the
	random failures described below.

	* tests/ser_test_protocol.inl: Add configuration for QUICC/MBX860.
	Added some delays in the configuration change code to make QUICC
	happy [didn't help much although the manual says they are required].

	* src/powerpc/quicc_smc_serial.h (UART_BITRATE): Rewrote macro to 
	match what the Linux driver uses - still doesn't work well, though.

	* src/powerpc/quicc_smc_serial.c: Lots of changes trying to get the
	serial driver working and robust.  At this point it works quite well,
	using the default buffer sizes.  Changing from the defaults seem to
	easily break it though, certainly on input.  Also, changing the baud
	rate seems to not work reliably.

	* src/common/serial.c: Add some tracing/debug info to try and debug
	problems with QUICC serial driver.  These are hard disabled with
	"XX_" prepended to "CYGDBG_DIAG_BUF".  Enabling them gives information
	about how/when data are delivered from the serial driver.

	* include/pkgconf/io_serial.h: Adjust limits and defaults on number and
	size of buffers with values that seem to work.

1999-06-21  Jesper Skov  <[e-mail]>

	* src/sh/sh_sci_serial.c: Rearranged inclusion of .inl file a bit
	to avoid compiler warnings.

1999-06-21  Gary Thomas  <[e-mail]>

	* include/pkgconf/io_serial.h: Fix CDL for number of buffers.

	* src/powerpc/quicc_smc_serial.c: Force number of buffers = 1.

1999-06-20  Gary Thomas  <[e-mail]>

	* include/pkgconf/io_serial.h: Some clean up (removed commented
	obsolete CDL parenting structure).
	Add support for Motorola PowerPC QUICC/SMC.

	* src/arm/cma230_serial.c: 
	* src/arm/cl7211_serial.c: 
	* src/arm/aeb_serial.c: 
	* src/arm/pid_serial_with_ints.c: Use #include to get 'diag_printf()'