3c501.c

GNU Mach 微内核源代码, 基于美国卡内基美隆大学的 Mach 研究项目

/* 3c501.c: A 3Com 3c501 ethernet driver for linux. */
/*
    Written 1992,1993,1994  Donald Becker

    Copyright 1993 United States Government as represented by the
    Director, National Security Agency.  This software may be used and
    distributed according to the terms of the GNU Public License,
    incorporated herein by reference.

    This is a device driver for the 3Com Etherlink 3c501.
    Do not purchase this card, even as a joke.  It's performance is horrible,
    and it breaks in many ways.  

    The author may be reached as [e-mail], or C/O
    Center of Excellence in Space Data and Information Sciences
       Code 930.5, Goddard Space Flight Center, Greenbelt MD 20771
       
    Fixed (again!) the missing interrupt locking on TX/RX shifting.
    		Alan Cox <[e-mail]>
    		
    Removed calls to init_etherdev since they are no longer needed, and
    cleaned up modularization just a bit. The driver still allows only
    the default address for cards when loaded as a module, but that's
    really less braindead than anyone using a 3c501 board. :)
		    19950208 ([e-mail])

    Added traps for interrupts hitting the window as we clear and TX load
    the board. Now getting 150K/second FTP with a 3c501 card. Still playing
    with a TX-TX optimisation to see if we can touch 180-200K/second as seems
    theoretically maximum.
    		19950402 Alan Cox <[e-mail]>
    		
    Some notes on this thing if you have to hack it.  [Alan]
    
    1]	Some documentation is available from 3Com. Due to the boards age
    	standard responses when you ask for this will range from 'be serious'
    	to 'give it to a museum'. The documentation is incomplete and mostly
    	of historical interest anyway.
    	
    2]  The basic system is a single buffer which can be used to receive or
    	transmit a packet. A third command mode exists when you are setting
    	things up.
    	
    3]	If it's transmitting it's not receiving and vice versa. In fact the 
    	time to get the board back into useful state after an operation is
    	quite large.
    	
    4]	The driver works by keeping the board in receive mode waiting for a
    	packet to arrive. When one arrives it is copied out of the buffer
    	and delivered to the kernel. The card is reloaded and off we go.
    	
    5]	When transmitting dev->tbusy is set and the card is reset (from
    	receive mode) [possibly losing a packet just received] to command
    	mode. A packet is loaded and transmit mode triggered. The interrupt
    	handler runs different code for transmit interrupts and can handle
    	returning to receive mode or retransmissions (yes you have to help
    	out with those too).
    	
    Problems:
    	There are a wide variety of undocumented error returns from the card
    and you basically have to kick the board and pray if they turn up. Most 
    only occur under extreme load or if you do something the board doesn't
    like (eg touching a register at the wrong time).
    
    	The driver is less efficient than it could be. It switches through
    receive mode even if more transmits are queued. If this worries you buy
    a real ethernet card.
    
    	The combination of slow receive restart and no real multicast
    filter makes the board unusable with a kernel compiled for IP
    multicasting in a real multicast environment. That's down to the board, 
    but even with no multicast programs running a multicast IP kernel is
    in group 224.0.0.1 and you will therefore be listening to all multicasts.
    One nv conference running over that ethernet and you can give up.
    
*/

static const char *version =
    "3c501.c: 9/23/94 Donald Becker ([e-mail]).\n";

/*
 *	Braindamage remaining:
 *	The 3c501 board.
 */

#include <linux/module.h>

#include <linux/kernel.h>
#include <linux/sched.h>
#include <linux/ptrace.h>
#include <linux/fcntl.h>
#include <linux/ioport.h>
#include <linux/interrupt.h>
#include <linux/malloc.h>
#include <linux/string.h>
#include <linux/errno.h>
#include <linux/config.h>	/* for CONFIG_IP_MULTICAST */

#include <asm/bitops.h>
#include <asm/io.h>

#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/skbuff.h>

#define BLOCKOUT_2

/* A zero-terminated list of I/O addresses to be probed.
   The 3c501 can be at many locations, but here are the popular ones. */
static unsigned int netcard_portlist[] =
   { 0x280, 0x300, 0};


/*
 *	Index to functions. 
 */
 
int el1_probe(struct device *dev);
static int  el1_probe1(struct device *dev, int ioaddr);
static int  el_open(struct device *dev);
static int  el_start_xmit(struct sk_buff *skb, struct device *dev);
static void el_interrupt(int irq, void *dev_id, struct pt_regs *regs);
static void el_receive(struct device *dev);
static void el_reset(struct device *dev);
static int  el1_close(struct device *dev);
static struct enet_statistics *el1_get_stats(struct device *dev);
static void set_multicast_list(struct device *dev);

#define EL1_IO_EXTENT	16

#ifndef EL_DEBUG
#define EL_DEBUG  0	/* use 0 for production, 1 for devel., >2 for debug */
#endif			/* Anything above 5 is wordy death! */
static int el_debug = EL_DEBUG;
 
/* 
 *	Board-specific info in dev->priv. 
 */
 
struct net_local 
{
    struct enet_statistics stats;
    int tx_pkt_start;		/* The length of the current Tx packet. */
    int collisions;		/* Tx collisions this packet */
    int loading;		/* Spot buffer load collisions */
};


#define RX_STATUS (ioaddr + 0x06)
#define RX_CMD	  RX_STATUS
#define TX_STATUS (ioaddr + 0x07)
#define TX_CMD	  TX_STATUS
#define GP_LOW 	  (ioaddr + 0x08)
#define GP_HIGH   (ioaddr + 0x09)
#define RX_BUF_CLR (ioaddr + 0x0A)
#define RX_LOW	  (ioaddr + 0x0A)
#define RX_HIGH   (ioaddr + 0x0B)
#define SAPROM	  (ioaddr + 0x0C)
#define AX_STATUS (ioaddr + 0x0E)
#define AX_CMD	  AX_STATUS
#define DATAPORT  (ioaddr + 0x0F)
#define TX_RDY 0x08		/* In TX_STATUS */

#define EL1_DATAPTR	0x08
#define EL1_RXPTR	0x0A
#define EL1_SAPROM	0x0C
#define EL1_DATAPORT 	0x0f

/*
 *	Writes to the ax command register.
 */
 
#define AX_OFF	0x00			/* Irq off, buffer access on */
#define AX_SYS  0x40			/* Load the buffer */
#define AX_XMIT 0x44			/* Transmit a packet */
#define AX_RX	0x48			/* Receive a packet */
#define AX_LOOP	0x0C			/* Loopback mode */
#define AX_RESET 0x80

/*
 *	Normal receive mode written to RX_STATUS.  We must intr on short packets
 *	to avoid bogus rx lockups.
 */
 
#define RX_NORM 0xA8		/* 0x68 == all addrs, 0xA8 only to me. */
#define RX_PROM 0x68		/* Senior Prom, uhmm promiscuous mode. */
#define RX_MULT 0xE8		/* Accept multicast packets. */
#define TX_NORM 0x0A		/* Interrupt on everything that might hang the chip */

/*
 *	TX_STATUS register. 
 */
 
#define TX_COLLISION 0x02
#define TX_16COLLISIONS 0x04
#define TX_READY 0x08

#define RX_RUNT 0x08
#define RX_MISSED 0x01		/* Missed a packet due to 3c501 braindamage. */
#define RX_GOOD	0x30		/* Good packet 0x20, or simple overflow 0x10. */


/*
 *	The boilerplate probe code.
 */
 
#ifdef HAVE_DEVLIST
struct netdev_entry el1_drv = {"3c501", el1_probe1, EL1_IO_EXTENT, netcard_portlist};
#else

int el1_probe(struct device *dev)
{
	int i;
	int base_addr = dev ? dev->base_addr : 0;

	if (base_addr > 0x1ff)	/* Check a single specified location. */
		return el1_probe1(dev, base_addr);
	else if (base_addr != 0)	/* Don't probe at all. */
		return ENXIO;

	for (i = 0; netcard_portlist[i]; i++) 
	{
		int ioaddr = netcard_portlist[i];
		if (check_region(ioaddr, EL1_IO_EXTENT))
			continue;
		if (el1_probe1(dev, ioaddr) == 0)
			return 0;
	}

	return ENODEV;
}
#endif

/*
 *	The actual probe. 
 */ 

static int el1_probe1(struct device *dev, int ioaddr)
{
	const char *mname;		/* Vendor name */
	unsigned char station_addr[6];
	int autoirq = 0;
	int i;

	/*
	 *	Read the station address PROM data from the special port.  
	 */
	 
	for (i = 0; i < 6; i++) 
	{
		outw(i, ioaddr + EL1_DATAPTR);
		station_addr[i] = inb(ioaddr + EL1_SAPROM);
	}
	/*
	 *	Check the first three octets of the S.A. for 3Com's prefix, or
	 *	for the Sager NP943 prefix. 
	 */ 
	 
	if (station_addr[0] == 0x02  &&  station_addr[1] == 0x60
		&& station_addr[2] == 0x8c) 
	{
		mname = "3c501";
	} else if (station_addr[0] == 0x00  &&  station_addr[1] == 0x80
	&& station_addr[2] == 0xC8) 
	{
		mname = "NP943";
    	}
    	else
		return ENODEV;

	/*
	 *	Grab the region so we can find the another board if autoIRQ fails. 
	 */

	request_region(ioaddr, EL1_IO_EXTENT,"3c501");

	/*	
	 *	We auto-IRQ by shutting off the interrupt line and letting it float
	 *	high.
	 */

	if (dev->irq < 2) 
	{
		autoirq_setup(2);
		inb(RX_STATUS);		/* Clear pending interrupts. */
		inb(TX_STATUS);
		outb(AX_LOOP + 1, AX_CMD);

		outb(0x00, AX_CMD);
	
		autoirq = autoirq_report(1);

		if (autoirq == 0) 
		{
			printk("%s probe at %#x failed to detect IRQ line.\n",
				mname, ioaddr);
			return EAGAIN;
		}
	}

	outb(AX_RESET+AX_LOOP, AX_CMD);			/* Loopback mode. */
	dev->base_addr = ioaddr;
	memcpy(dev->dev_addr, station_addr, ETH_ALEN);

	if (dev->mem_start & 0xf)
		el_debug = dev->mem_start & 0x7;
	if (autoirq)
		dev->irq = autoirq;

	printk("%s: %s EtherLink at %#lx, using %sIRQ %d.\n", dev->name, mname, dev->base_addr,
			autoirq ? "auto":"assigned ", dev->irq);
	   
#ifdef CONFIG_IP_MULTICAST
	printk("WARNING: Use of the 3c501 in a multicast kernel is NOT recommended.\n");
#endif    

	if (el_debug)
		printk("%s", version);

	/*
	 *	Initialize the device structure. 
	 */
	 
	dev->priv = kmalloc(sizeof(struct net_local), GFP_KERNEL);
	if (dev->priv == NULL)
		return -ENOMEM;
	memset(dev->priv, 0, sizeof(struct net_local));

	/*
	 *	The EL1-specific entries in the device structure. 
	 */
	 
	dev->open = &el_open;
	dev->hard_start_xmit = &el_start_xmit;
	dev->stop = &el1_close;
	dev->get_stats = &el1_get_stats;
	dev->set_multicast_list = &set_multicast_list;

	/*
	 *	Setup the generic properties 
	 */

	ether_setup(dev);

	return 0;
}

/*
 *	Open/initialize the board. 
 */
 
static int el_open(struct device *dev)
{
	int ioaddr = dev->base_addr;

	if (el_debug > 2)
		printk("%s: Doing el_open()...", dev->name);

	if (request_irq(dev->irq, &el_interrupt, 0, "3c501", NULL)) 
		return -EAGAIN;

	irq2dev_map[dev->irq] = dev;
	el_reset(dev);

	dev->start = 1;

	outb(AX_RX, AX_CMD);	/* Aux control, irq and receive enabled */
	MOD_INC_USE_COUNT;
	return 0;
}

static int el_start_xmit(struct sk_buff *skb, struct device *dev)
{
	struct net_local *lp = (struct net_local *)dev->priv;
	int ioaddr = dev->base_addr;
	unsigned long flags;
	
	if(dev->interrupt)		/* May be unloading, don't stamp on */
		return 1;		/* the packet buffer this time      */

	if (dev->tbusy) 
	{
		if (jiffies - dev->trans_start < 20) 
		{
			if (el_debug > 2)
				printk(" transmitter busy, deferred.\n");
			return 1;
		}
		if (el_debug)
			printk ("%s: transmit timed out, txsr %#2x axsr=%02x rxsr=%02x.\n",
				dev->name, inb(TX_STATUS), inb(AX_STATUS), inb(RX_STATUS));
		lp->stats.tx_errors++;
		outb(TX_NORM, TX_CMD);
		outb(RX_NORM, RX_CMD);
		outb(AX_OFF, AX_CMD);	/* Just trigger a false interrupt. */
		outb(AX_RX, AX_CMD);	/* Aux control, irq and receive enabled */
		dev->tbusy = 0;
		dev->trans_start = jiffies;
	}

	if (skb == NULL) 
	{
		dev_tint(dev);
		return 0;
	}

	save_flags(flags);

	/*
	 *	Avoid incoming interrupts between us flipping tbusy and flipping
	 *	mode as the driver assumes tbusy is a faithful indicator of card
	 *	state
	 */
	 
	cli();
	
	/*
	 *	Avoid timer-based retransmission conflicts. 
	 */
	 
	if (set_bit(0, (void*)&dev->tbusy) != 0)
	{
		restore_flags(flags);
		printk("%s: Transmitter access conflict.\n", dev->name);
	}
	else
	{
		int gp_start = 0x800 - (ETH_ZLEN < skb->len ? skb->len : ETH_ZLEN);
		unsigned char *buf = skb->data;