fet110_ta_uart9600_04.c

各种波特路的串口通信程序（还是MSP430 ）

//******************************************************************************
//  MSP-FET430x110 Demo - Timer_A UART Ultra-low Power 9600 Echo, No XTAL ROSC
//
//  Description: This program demonstrates a half-duplex 9600-baud UART using 
//  Timer_A3 using no XTAL and an external resistor for DCO ROSC. DCO used for
//  TACLK UART baud generation. The program will wait in LPM4, echoing back
//  a received character using 8N1 protocol. On valid RX character, the 
//  character is echoed back. 
//  Using a 100k resistor on ROSC, with default DCO setting, set DCOCLK ~ 2MHz.
//  ACLK = n/a, MCLK = SMCLK ~ 2MHz DCOCLK
//  //*Use of external resistor reduces temperature sensitivity of DCOCLK*//
//
//               MSP430F1121
//            -----------------
//  /|\   /|\|              XIN|-  
//   |     | |                 | 
//  100k   --|RST          XOUT|-
//   |       |                 |
//   +-------|P2.5/ROSC        | 
//           |   CCI0A/TXD/P1.1|-------->  
//           |                 | 9600 8N1 
//           |   CCI0B/RXD/P2.2|<--------
//
#define RXD   0x04                      // RXD on P2.2
#define TXD   0x02                      // TXD on P1.1

//   Conditions for 9600 Baud SW UART, DCO ~ 2MHz

#define Bitime_5  104                  // ~ 0.5 bit length 
#define Bitime    208                  // ~ 9615 baud

unsigned int RXTXData;
unsigned char BitCnt;

void TX_Byte (void);
void RX_Ready (void);

//  M.Buccini
//  Texas Instruments, Inc
//  January 2004
//  Updated for IAR Embedded Workbench Version: 2.21B
//******************************************************************************

#include <msp430x11x1.h>


void main (void)
{
  WDTCTL = WDTPW + WDTHOLD;             // Stop watchdog timer
  BCSCTL2 |= DCOR;                      // Rosc
  _BIS_SR(OSCOFF);                      // XTAL not used
  CCTL0 = OUT;                          // TXD Idle as Mark 
  TACTL = TASSEL_2 + MC_2;              // SMCLK, continuous mode
  P1SEL = TXD;                          // P1.1/TA0 for TXD function
  P1DIR = TXD;                          // TXD output on P1
  P2SEL = RXD;                          // P2.2/TA0 as RXD input

// Mainloop
  for (;;)                              
  {
  RX_Ready();                           // UART ready to RX one Byte
  _BIS_SR(LPM4_bits + GIE);             // Enter LPM0 w/ interr until char RXed
  TX_Byte();                            // TX Back RXed Byte Received
  }
}


// Function Transmits Character from RXTXData Buffer
void TX_Byte (void)
{
  BitCnt = 0xA;                         // Load Bit counter, 8data + ST/SP
  CCR0 = TAR;                           // Current state of TA counter
  CCR0 += Bitime;                       // Some time till first bit
  RXTXData |= 0x100;                    // Add mark stop bit to RXTXData 
  RXTXData = RXTXData << 1;             // Add space start bit
  CCTL0 = OUTMOD0 + CCIE;               // TXD = mark = idle 
  while ( CCTL0 & CCIE );               // Wait for TX completion
}


// Function Readies UART to Receive Character into RXTXData Buffer
// Sync capture not possible as DCO=TACLK=SMCLK can be off !!
void RX_Ready (void)
{
  BitCnt = 0x8;                         // Load Bit counter
  CCTL0 = CM1 + CCIS0 + OUTMOD0 + CAP + CCIE;   // Neg Edge, Cap          
}


// Timer A0 interrupt service routine
#pragma vector=TIMERA0_VECTOR
__interrupt void Timer_A0 (void)
{
  CCR0 += Bitime;                       // Add Offset to CCR0

// RX
  if (CCTL0 & CCIS0)                    // RX on CCI0B?
  {
    if( CCTL0 & CAP )                   // Capture mode = start bit edge
    {
    CCTL0 &= ~ CAP;                     // Switch from capture to compare mode 
    CCR0 += Bitime_5;
    _BIC_SR_IRQ(SCG1 + SCG0);           // DCO reamins on after reti
    }
    else
    {
    RXTXData = RXTXData >> 1;           
      if (CCTL0 & SCCI)                 // Get bit waiting in receive latch
      RXTXData |= 0x80;                 
      BitCnt --;                        // All bits RXed?
      if ( BitCnt == 0)
//>>>>>>>>>> Decode of Received Byte Here <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
      {
      CCTL0 &= ~ CCIE;                  // All bits RXed, disable interrupt
      _BIC_SR_IRQ(CPUOFF);              // Active mode on reti 0(SR)
      }
//>>>>>>>>>> Decode of Received Byte Here <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
    }
  }
// TX
  else
  {
    if ( BitCnt == 0)
    CCTL0 &= ~ CCIE;                    // All bits TXed, disable interrupt
    else
    {
      CCTL0 |=  OUTMOD2;                  // TX Space
      if (RXTXData & 0x01)                 
      CCTL0 &= ~ OUTMOD2;                 // TX Mark
      RXTXData = RXTXData >> 1;
      BitCnt --;
    }
  }
}