fet140_uart01_09600.s43

用MSP430单片机的汇编语言写的串口接发程序

#include  "msp430x13x.h"
;******************************************************************************
;   MSP-FET430P140 Demo - USART0 UART 9600 Echo ISR, HF XTAL ACLK
;
;   Description; Echo a received character, RX ISR used. Normal mode is LPM0, 
;   USART0 RX interrupt triggers TX Echo. Though not required, MCLK = LFXT1  
;   ACLK = MCLK = UCLK0 = LFXT1 = 3.58MHz 
;   Baud rate divider with 3.58Mhz XTAL @9600 = 3.58MHz/9600 = 372 (0174h)
;   //*An external 3.58MHz XTAL on XIN XOUT is required for ACLK*//	  
;              
;                MSP430F149
;             -----------------
;         /|\|              XIN|-  
;          | |                 | 3.58MHz  
;          --|RST          XOUT|-
;            |                 |
;            |             P3.4|------------> 
;            |                 | 9600 - 8N1
;            |             P3.5|<------------
;
;    M.Buccini
;    Texas Instruments, Inc
;    January 2002
;******************************************************************************
;------------------------------------------------------------------------------ 
            ORG     0E000h                  ; Program Start
;------------------------------------------------------------------------------ 
RESET       mov.w   #0300h,SP               ; Initialize 'F149 stackpointer
            call    #Init_Sys               ;
                                            ;   
Mainloop    bis.b   #CPUOFF,SR              ; Enter LPM0
            nop                             ; Needed only for C-spy
                                            ;
;------------------------------------------------------------------------------
Init_Sys;   Initalize MSP430 system
;------------------------------------------------------------------------------
StopWDT     mov.w   #WDTPW+WDTHOLD,&WDTCTL  ; Stop WDT
            MOV.B   #83H,&BCSCTL1
SetupUART0  mov.b   #CHAR,&UCTL0            ; 8-bit characters
            mov.b   #SSEL1,&UTCTL0          ; UCLK = ACLK
            mov.b   #030h,&UBR00            ; 32k/2400 - 13.65
            mov.b   #000h,&UBR10            ; 32k 2400
            mov.b   #0DBh,&UMCTL0           ; 32k 2400 modulation 
            bis.b   #UTXE0+URXE0,&ME1       ; Enable USART0 TXD/RXD
            bis.b   #URXIE0,&IE1            ; Enable USART0 RX interrupt
SetupP3     bis.b   #030h,&P3SEL            ; P3.4,5 = USART0 TXD/RXD
            bis.b   #010h,&P3DIR            ; P3.4 = output direction 
            eint                            ; General enable interrupts
            ret                             ; Return from subroutine
                                            ;             
;------------------------------------------------------------------------------
USART0RX_ISR;  Echo back RXed character, confirm TX buffer is ready first
;------------------------------------------------------------------------------
TX1         bit.b   #UTXIFG0,&IFG1          ; USART0 TX buffer ready?
            jz      TX1                     ; Jump is TX buffer not ready
            mov.b   &RXBUF0,&TXBUF0         ; TX -> RXed character
            reti                            ; 
                                            ;
;------------------------------------------------------------------------------
;           Interrupt Vectors Used MSP430x13x/14x        
;------------------------------------------------------------------------------
            ORG     0FFFEh                  ; 
            DW      RESET                   ; POR, ext. Reset, Watchdog
            ORG     0FFF2h                  ; 
            DW      USART0RX_ISR            ; USART0 receive
            end