📄 lwipopts.small.h
字号:
//
// lwipopts.h
//
// Contains preprocessor definitions to guide a build of the lwIP code.
//
#ifndef _LWIPOPTS_H_
#define _LWIPOPTS_H_
#define NO_SYS 0
/*#define LWIP_EVENT_API 0*/
/* ---------- Memory options ---------- */
/* MEM_ALIGNMENT: should be set to the alignment of the CPU for which
lwIP is compiled. 4 byte alignment -> define MEM_ALIGNMENT to 4, 2
byte alignment -> define MEM_ALIGNMENT to 2. */
#define MEM_ALIGNMENT 4
/* MEM_SIZE: the size of the heap memory. If the application will send
a lot of data that needs to be copied, this should be set high. */
#define MEM_SIZE 16384
/* MEMP_NUM_PBUF: the number of memp struct pbufs. If the application
sends a lot of data out of ROM (or other static memory), this
should be set high. */
#define MEMP_NUM_PBUF 16
/* MEMP_NUM_UDP_PCB: the number of UDP protocol control blocks. One
per active UDP "connection". */
#define MEMP_NUM_UDP_PCB 4
/* MEMP_NUM_TCP_PCB: the number of simulatenously active TCP
connections. */
#define MEMP_NUM_TCP_PCB 5
/* MEMP_NUM_TCP_PCB_LISTEN: the number of listening TCP
connections. */
#define MEMP_NUM_TCP_PCB_LISTEN 8
/* MEMP_NUM_TCP_SEG: the number of simultaneously queued TCP
segments. */
#define MEMP_NUM_TCP_SEG 16
/* MEMP_NUM_SYS_TIMEOUT: the number of simulateously active
timeouts. */
#define MEMP_NUM_SYS_TIMEOUT 3
/* The following four are used only with the sequential API and can be
set to 0 if the application only will use the raw API. */
/* MEMP_NUM_NETBUF: the number of struct netbufs. */
#define MEMP_NUM_NETBUF 6
/* MEMP_NUM_NETCONN: the number of struct netconns. */
#define MEMP_NUM_NETCONN 10
/* MEMP_NUM_APIMSG: the number of struct api_msg, used for
communication between the TCP/IP stack and the sequential
programs. */
#define MEMP_NUM_API_MSG 16
/* MEMP_NUM_TCPIPMSG: the number of struct tcpip_msg, which is used
for sequential API communication and incoming packets. Used in
src/api/tcpip.c. */
#define MEMP_NUM_TCPIP_MSG 16
/* These two control whether reclaimer functions should be compiled
in. Should always be turned on (1). */
#define MEM_RECLAIM 1
#define MEMP_RECLAIM 1
/* ---------- Pbuf options ---------- */
/* PBUF_POOL_SIZE: the number of buffers in the pbuf pool. */
#define PBUF_POOL_SIZE 64
/* PBUF_POOL_BUFSIZE: the size of each pbuf in the pbuf pool. */
#define PBUF_POOL_BUFSIZE 512
/* PBUF_LINK_HLEN: the number of bytes that should be allocated for a
link level header. */
#define PBUF_LINK_HLEN 16
/* ---------- TCP options ---------- */
#define LWIP_TCP 1
#define TCP_TTL 255
/* Controls if TCP should queue segments that arrive out of
order. Define to 0 if your device is low on memory. */
#define TCP_QUEUE_OOSEQ 1
/* TCP Maximum segment size. */
#define TCP_MSS 128
/* TCP sender buffer space (bytes). */
#define TCP_SND_BUF 256
/* TCP sender buffer space (pbufs). This must be at least = 2 *
TCP_SND_BUF/TCP_MSS for things to work. */
#define TCP_SND_QUEUELEN 4 * TCP_SND_BUF/TCP_MSS
/* TCP receive window. */
#define TCP_WND 1024
/* Maximum number of retransmissions of data segments. */
#define TCP_MAXRTX 12
/* Maximum number of retransmissions of SYN segments. */
#define TCP_SYNMAXRTX 4
/* TCP writable space (bytes). This must be less than or equal
to TCP_SND_BUF. It is the amount of space which must be
available in the tcp snd_buf for select to return writable */
#define TCP_SNDLOWAT TCP_SND_BUF/2
/* ---------- ARP options ---------- */
#define ARP_TABLE_SIZE 10
#define ARP_QUEUEING 1
/**
* - If enabled, cache entries are generated for every kind of ARP traffic or
* broadcast IP traffic. This enhances behaviour for sending to a dynamic set
* of hosts, for example if acting as a gateway.
* - If disabled, cache entries are generated only for IP destination addresses
* in use by lwIP or applications. This enhances performance if sending to a
* small, reasonably static number of hosts. Typically for embedded devices.
*/
#define ETHARP_ALWAYS_INSERT 1
/* ---------- IP options ---------- */
/* Define IP_FORWARD to 1 if you wish to have the ability to forward
IP packets across network interfaces. If you are going to run lwIP
on a device with only one network interface, define this to 0. */
#define IP_FORWARD 1
/* If defined to 1, IP options are allowed (but not parsed). If
defined to 0, all packets with IP options are dropped. */
#define IP_OPTIONS 1
/* IP reassembly and segmentation.These are orthogonal even
* if they both deal with IP fragments */
#define IP_REASSEMBLY 1
#define IP_FRAG 1
/* ---------- ICMP options ---------- */
#define ICMP_TTL 255
/* ---------- DHCP options ---------- */
/* Define LWIP_DHCP to 1 if you want DHCP configuration of
interfaces. */
#define LWIP_DHCP 1
/* 1 if you want to do an ARP check on the offered address
(recommended). */
#define DHCP_DOES_ARP_CHECK 1
/* ---------- UDP options ---------- */
#define LWIP_UDP 1
#define UDP_TTL 255
/* ---------- Statistics options ---------- */
#define LWIP_STATS 1
#ifdef LWIP_STATS
#define LINK_STATS
#define IP_STATS
#define ICMP_STATS
#define UDP_STATS
#define TCP_STATS
#define MEM_STATS
#define MEMP_STATS
#define PBUF_STATS
#define SYS_STATS
#endif /* STATS */
/** SYS_LIGHTWEIGHT_PROT
* define SYS_LIGHTWEIGHT_PROT in lwipopts.h if you want inter-task
* protection for certain critical regions during buffer allocation
* and deallocation and memory allocation and deallocation.
*/
#define SYS_LIGHTWEIGHT_PROT 1
#define LWIP_COMPAT_SOCKETS 1
#define LWIP_PROVIDE_ERRNO 1
// thread priorities are in VDK terms - 1 is highest, 30 is lowest
#define TCPIP_THREAD_PRIO 5
#define DEFAULT_THREAD_PRIO 10
#define LOW_THREAD_PRIO 29
#endif // _LWIPOPTS_H_
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -