config.in

linux-2.4.29操作系统的源码

    if [ "$CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_ON_PA" = "y" -o \
         "$CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED" = "y" ]; then
      int '    Ser3 DTR on PA bit (-1 = not used)' CONFIG_ETRAX_SER3_DTR_ON_PA_BIT -1
      int '    Ser3 RI  on PA bit (-1 = not used)' CONFIG_ETRAX_SER3_RI_ON_PA_BIT -1
      int '    Ser3 DSR on PA bit (-1 = not used)' CONFIG_ETRAX_SER3_DSR_ON_PA_BIT -1
      int '    Ser3 CD  on PA bit (-1 = not used)' CONFIG_ETRAX_SER3_CD_ON_PA_BIT -1
    else
      define_int CONFIG_ETRAX_SER3_DTR_ON_PA_BIT -1
      define_int CONFIG_ETRAX_SER3_RI_ON_PA_BIT -1
      define_int CONFIG_ETRAX_SER3_DSR_ON_PA_BIT -1
      define_int CONFIG_ETRAX_SER3_CD_ON_PA_BIT -1
    fi
    if [ "$CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_ON_PB" = "y" -o \
         "$CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED" = "y" ]; then
      int '    Ser3 DTR on PB bit (-1 = not used)' CONFIG_ETRAX_SER3_DTR_ON_PB_BIT -1
      int '    Ser3 RI  on PB bit (-1 = not used)' CONFIG_ETRAX_SER3_RI_ON_PB_BIT -1
      int '    Ser3 DSR on PB bit (-1 = not used)' CONFIG_ETRAX_SER3_DSR_ON_PB_BIT -1
      int '    Ser3 CD  on PB bit (-1 = not used)' CONFIG_ETRAX_SER3_CD_ON_PB_BIT -1
    else
      define_int CONFIG_ETRAX_SER3_DTR_ON_PB_BIT -1
      define_int CONFIG_ETRAX_SER3_RI_ON_PB_BIT -1
      define_int CONFIG_ETRAX_SER3_DSR_ON_PB_BIT -1
      define_int CONFIG_ETRAX_SER3_CD_ON_PB_BIT -1
    fi
  fi
  bool '  RS-485 support' CONFIG_ETRAX_RS485
  if [ "$CONFIG_ETRAX_RS485" = "y" ]; then
    bool '    RS-485 mode on PA' CONFIG_ETRAX_RS485_ON_PA
    if [ "$CONFIG_ETRAX_RS485_ON_PA" = "y" ]; then
      int '      RS-485 mode on PA bit' CONFIG_ETRAX_RS485_ON_PA_BIT 3
    fi
    bool '    Disable serial receiver' CONFIG_ETRAX_RS485_DISABLE_RECEIVER
  fi
fi

bool 'Synchronous serial port support' CONFIG_ETRAX_SYNCHRONOUS_SERIAL
if [ "$CONFIG_ETRAX_SYNCHRONOUS_SERIAL" = "y" ]; then 
  bool '  Synchronous serial port 0 enabled (sser1)' CONFIG_ETRAX_SYNCHRONOUS_SERIAL_PORT0
  if [ "$CONFIG_ETRAX_SYNCHRONOUS_SERIAL_PORT0" = "y" ]; then
    bool '    Synchronous serial port 0 uses DMA 8,9' CONFIG_ETRAX_SYNCHRONOUS_SERIAL0_DMA
  fi
  bool '  Synchronous serial port 1 enabled (sser3)' CONFIG_ETRAX_SYNCHRONOUS_SERIAL_PORT1
  if [ "$CONFIG_ETRAX_SYNCHRONOUS_SERIAL_PORT1" = "y" ]; then
    bool '    Synchronous serial port 1 uses DMA 4,5' CONFIG_ETRAX_SYNCHRONOUS_SERIAL1_DMA
  fi 
fi

bool 'Parallel port support' CONFIG_ETRAX_PARPORT
if [ "$CONFIG_ETRAX_PARPORT" = "y" ]; then
	bool '  Parallel port 0 enabled' CONFIG_ETRAX_PARALLEL_PORT0
	bool '  Parallel port 1 enabled' CONFIG_ETRAX_PARALLEL_PORT1
# here we define the CONFIG_'s necessary to enable parallel port support
	define_tristate CONFIG_PARPORT y
        define_bool CONFIG_PARPORT_1284 y
        define_tristate CONFIG_PRINTER y
else
	define_tristate CONFIG_PARPORT n
        define_bool CONFIG_PARPORT_1284 n
        define_tristate CONFIG_PRINTER n
fi


bool 'ATA/IDE support' CONFIG_ETRAX_IDE

if [ "$CONFIG_ETRAX_IDE" = "y" ]; then
# here we should add the CONFIG_'s necessary to enable the basic
# general ide drivers so the common case does not need to go
# into that config submenu. enable disk and CD support. others
# need to go fiddle in the submenu..
	define_bool CONFIG_IDE y

	define_bool CONFIG_BLK_DEV_IDE y
	define_bool CONFIG_BLK_DEV_IDEDISK y
	define_bool CONFIG_BLK_DEV_IDECD y

	define_bool CONFIG_BLK_DEV_IDEDMA y
	define_bool CONFIG_DMA_NONPCI y
	
	int 'Delay for drives to regain consciousness' CONFIG_ETRAX_IDE_DELAY 15
	
	choice 'IDE reset pin' \
  	"Port_PB_Bit_7  CONFIG_ETRAX_IDE_PB7_RESET\
   	 Port_G_Bit_27  CONFIG_ETRAX_IDE_G27_RESET\
	 Port_CSE1_Bit_16  CONFIG_ETRAX_IDE_CSE1_16_RESET\
	 Port_CSP0_Bit_08   CONFIG_ETRAX_IDE_CSP0_8_RESET"  Port_PB_Bit_7
else
	define_bool CONFIG_IDE n
fi

bool 'Axis flash-map support' CONFIG_ETRAX_AXISFLASHMAP

if [ "$CONFIG_ETRAX_AXISFLASHMAP" = "y" ]; then
        int  '  Byte-offset of partition table sector' CONFIG_ETRAX_PTABLE_SECTOR 65536
# here we define the CONFIG_'s necessary to enable MTD support
# for the flash
	define_bool CONFIG_MTD y
	define_bool CONFIG_MTD_PARTITIONS y
	define_bool CONFIG_MTD_CHAR y
	define_bool CONFIG_MTD_BLOCK y

	if [ "$CONFIG_MTD_CFI" = "n" ] && [ "$CONFIG_MTD_AMDSTD" = "n" ] && \
	   [ "$CONFIG_MTD_MTDRAM" = "n" ]; then
		# Bad initial configuration, make axisflashmap work by enabling
		# all drivers it may need.

		define_bool CONFIG_MTD_CFI y
		define_bool CONFIG_MTD_CFI_AMDSTD y

		define_bool CONFIG_MTD_OBSOLETE_CHIPS y
		define_bool CONFIG_MTD_AMDSTD y

		define_bool CONFIG_MTD_CONCAT y

		define_bool CONFIG_MTD_MTDRAM y
		define_int CONFIG_MTDRAM_TOTAL_SIZE 0
		define_int CONFIG_MTDRAM_ERASE_SIZE 64
		define_int CONFIG_MTDRAM_ABS_POS 0
	fi
fi

bool 'I2C support' CONFIG_ETRAX_I2C
if [ "$CONFIG_ETRAX_I2C" = "y" ]; then
# this is true for most products since PB-I2C seems to be somewhat
# flawed.. 
	bool 'I2C uses PB not PB-I2C' CONFIG_ETRAX_I2C_USES_PB_NOT_PB_I2C

	if [ "$CONFIG_ETRAX_I2C_USES_PB_NOT_PB_I2C" = "y" ]; then
          int '  I2C SDA bit number' CONFIG_ETRAX_I2C_DATA_PORT 0
          int '  I2C SCL bit number' CONFIG_ETRAX_I2C_CLK_PORT 1
	fi
fi

bool 'I2C EEPROM (non-volatile RAM) support' CONFIG_ETRAX_I2C_EEPROM
if [ "$CONFIG_ETRAX_I2C_EEPROM" = "y" ]; then
  choice '  EEPROM size' \
    "Probed CONFIG_ETRAX_I2C_EEPROM_PROBE \
     2kB    CONFIG_ETRAX_I2C_EEPROM_2KB   \
     8kB    CONFIG_ETRAX_I2C_EEPROM_8KB   \
     16kB   CONFIG_ETRAX_I2C_EEPROM_16KB" Probed
fi

bool 'GPIO support' CONFIG_ETRAX_GPIO
if [ "$CONFIG_ETRAX_GPIO" = "y" ]; then
  hex  '  PA-buttons bitmask' CONFIG_ETRAX_PA_BUTTON_BITMASK 02
  hex  '  PA user changeable dir mask' CONFIG_ETRAX_PA_CHANGEABLE_DIR 00
  hex  '  PA user changeable bits mask' CONFIG_ETRAX_PA_CHANGEABLE_BITS FF
  hex  '  PB user changeable dir mask' CONFIG_ETRAX_PB_CHANGEABLE_DIR 00
  hex  '  PB user changeable bits mask' CONFIG_ETRAX_PB_CHANGEABLE_BITS FF
fi

bool 'ARTPEC-1 support' CONFIG_JULIETTE

if [ "$CONFIG_JULIETTE" = "y" ]; then

fi

bool 'VIRTEX FPGA support' CONFIG_ETRAX_VIRTEX_FPGA

bool 'USB host' CONFIG_ETRAX_USB_HOST
if [ "$CONFIG_ETRAX_USB_HOST" = "y" ]; then
	define_bool CONFIG_USB y
	bool '  USB port 1 enabled' CONFIG_ETRAX_USB_HOST_PORT1
	bool '  USB port 2 enabled' CONFIG_ETRAX_USB_HOST_PORT2
else
	define_bool CONFIG_USB n
fi

bool 'Real Time Clock support' CONFIG_ETRAX_RTC
if [ "$CONFIG_ETRAX_RTC" = "y" ]; then
  bool '  Enable RTC read only mode' CONFIG_ETRAX_RTC_READONLY	 
  choice '  RTC chip' \
    "DS1302 CONFIG_ETRAX_DS1302 \
     PCF8563  CONFIG_ETRAX_PCF8563" DS1302
fi

if [ "$CONFIG_ETRAX_DS1302" = "y" ]; then
  bool '  DS1302 RST on Generic Port' CONFIG_ETRAX_DS1302_RST_ON_GENERIC_PORT
  int '  DS1302 RST bit number' CONFIG_ETRAX_DS1302_RSTBIT 2
  int '  DS1302 SCL bit number' CONFIG_ETRAX_DS1302_SCLBIT 1
  int '  DS1302 SDA bit number' CONFIG_ETRAX_DS1302_SDABIT 0
  int '  DS1302 Trickle charger value' CONFIG_ETRAX_DS1302_TRICKLE_CHARGE 0
fi

endmenu