hal_cache.h

ecos为实时嵌入式操作系统

#ifndef CYGONCE_HAL_CACHE_H
#define CYGONCE_HAL_CACHE_H

//=============================================================================
//
//      hal_cache.h
//
//      HAL cache control API
//
//=============================================================================
//####COPYRIGHTBEGIN####
//
// -------------------------------------------
// The contents of this file are subject to the Cygnus eCos Public License
// Version 1.0 (the "License"); you may not use this file except in
// compliance with the License.  You may obtain a copy of the License at
// http://sourceware.cygnus.com/ecos
// 
// Software distributed under the License is distributed on an "AS IS"
// basis, WITHOUT WARRANTY OF ANY KIND, either express or implied.  See the
// License for the specific language governing rights and limitations under
// the License.
// 
// The Original Code is eCos - Embedded Cygnus Operating System, released
// September 30, 1998.
// 
// The Initial Developer of the Original Code is Cygnus.  Portions created
// by Cygnus are Copyright (C) 1998,1999 Cygnus Solutions.  All Rights Reserved.
// -------------------------------------------
//
//####COPYRIGHTEND####
//=============================================================================
//#####DESCRIPTIONBEGIN####
//
// Author(s):   nickg
// Contributors:        nickg
// Date:        1998-02-17
// Purpose:     Cache control API
// Description: The macros defined here provide the HAL APIs for handling
//              cache control operations.
// Usage:
//              #include <cyg/hal/hal_cache.h>
//              ...
//              
//
//####DESCRIPTIONEND####
//
//=============================================================================

#include <pkgconf/hal.h>
#include <cyg/infra/cyg_type.h>

#include <cyg/hal/ppc_regs.h>

//=============================================================================
// Memory mapping
typedef struct {
    CYG_ADDRESS  virtual_addr;
    CYG_ADDRESS  physical_addr;
    cyg_int32    size;
    cyg_uint8    flags;
} cyg_memdesc_t;

#define CYGARC_MEMDESC_CI       1       // cache inhibit
#define CYGARC_MEMDESC_GUARDED  2       // guarded

//=============================================================================
// PowerPC simulator

#ifdef CYG_HAL_POWERPC_SIM

//-----------------------------------------------------------------------------
// Cache dimensions

// Data cache
#define HAL_DCACHE_SIZE                 4096    // Size of data cache in bytes
#define HAL_DCACHE_LINE_SIZE            16      // Size of a data cache line
#define HAL_DCACHE_WAYS                 2       // Associativity of the cache

// Instruction cache
#define HAL_ICACHE_SIZE                 4096    // Size of cache in bytes
#define HAL_ICACHE_LINE_SIZE            16      // Size of a cache line
#define HAL_ICACHE_WAYS                 2       // Associativity of the cache

#define HAL_DCACHE_SETS (HAL_DCACHE_SIZE/(HAL_DCACHE_LINE_SIZE*HAL_DCACHE_WAYS))
#define HAL_ICACHE_SETS (HAL_ICACHE_SIZE/(HAL_ICACHE_LINE_SIZE*HAL_ICACHE_WAYS))

//-----------------------------------------------------------------------------
// Global control of data cache

// Enable the data cache
#define HAL_DCACHE_ENABLE()

// Disable the data cache
#define HAL_DCACHE_DISABLE()

// Invalidate the entire cache
#define HAL_DCACHE_INVALIDATE_ALL()

// Synchronize the contents of the cache with memory.
#define HAL_DCACHE_SYNC()

// Query the state of the data cache
#define HAL_DCACHE_IS_ENABLED(_state_)          \
    CYG_MACRO_START                             \
    (_state_) = 0;                              \
    CYG_MACRO_END

// Set the data cache refill burst size
//#define HAL_DCACHE_BURST_SIZE(_size_)

// Set the data cache write mode
//#define HAL_DCACHE_WRITE_MODE( _mode_ )

//#define HAL_DCACHE_WRITETHRU_MODE       0
//#define HAL_DCACHE_WRITEBACK_MODE       1

// Load the contents of the given address range into the data cache
// and then lock the cache so that it stays there.
//#define HAL_DCACHE_LOCK(_base_, _size_)

// Undo a previous lock operation
//#define HAL_DCACHE_UNLOCK(_base_, _size_)

// Unlock entire cache
//#define HAL_DCACHE_UNLOCK_ALL()

//-----------------------------------------------------------------------------
// Data cache line control

// Allocate cache lines for the given address range without reading its
// contents from memory.
//#define HAL_DCACHE_ALLOCATE( _base_ , _size_ )

// Write dirty cache lines to memory and invalidate the cache entries
// for the given address range.
//#define HAL_DCACHE_FLUSH( _base_ , _size_ )

// Invalidate cache lines in the given range without writing to memory.
//#define HAL_DCACHE_INVALIDATE( _base_ , _size_ )

// Write dirty cache lines to memory for the given address range.
//#define HAL_DCACHE_STORE( _base_ , _size_ )

// Preread the given range into the cache with the intention of reading
// from it later.
//#define HAL_DCACHE_READ_HINT( _base_ , _size_ )

// Preread the given range into the cache with the intention of writing
// to it later.
//#define HAL_DCACHE_WRITE_HINT( _base_ , _size_ )

// Allocate and zero the cache lines associated with the given range.
//#define HAL_DCACHE_ZERO( _base_ , _size_ )

//-----------------------------------------------------------------------------
// Global control of Instruction cache

// Enable the instruction cache
#define HAL_ICACHE_ENABLE()

// Disable the instruction cache
#define HAL_ICACHE_DISABLE()

// Invalidate the entire cache
#define HAL_ICACHE_INVALIDATE_ALL()

// Synchronize the contents of the cache with memory.
#define HAL_ICACHE_SYNC()

// Query the state of the instruction cache
#define HAL_ICACHE_IS_ENABLED(_state_)          \
    CYG_MACRO_START                             \
    (_state_) = 0;                              \
    CYG_MACRO_END

// Set the instruction cache refill burst size
//#define HAL_ICACHE_BURST_SIZE(_size_)

// Load the contents of the given address range into the instruction cache
// and then lock the cache so that it stays there.
//#define HAL_ICACHE_LOCK(_base_, _size_)

// Undo a previous lock operation
//#define HAL_ICACHE_UNLOCK(_base_, _size_)

// Unlock entire cache
//#define HAL_ICACHE_UNLOCK_ALL()

//-----------------------------------------------------------------------------
// Instruction cache line control

// Invalidate cache lines in the given range without writing to memory.
//#define HAL_ICACHE_INVALIDATE( _base_ , _size_ )


//=============================================================================
// Motorola MPC8xx

#elif defined(CYG_HAL_POWERPC_MPC8xx)

//-----------------------------------------------------------------------------
// Cache dimensions

#if defined(CYG_HAL_POWERPC_MPC860)
// Data cache
#define HAL_DCACHE_SIZE                 4096    // Size of data cache in bytes
#define HAL_DCACHE_LINE_SIZE            16      // Size of a data cache line
#define HAL_DCACHE_WAYS                 2       // Associativity of the cache

// Instruction cache
#define HAL_ICACHE_SIZE                 4096    // Size of cache in bytes
#define HAL_ICACHE_LINE_SIZE            16      // Size of a cache line
#define HAL_ICACHE_WAYS                 2       // Associativity of the cache
#endif // defined(CYG_HAL_POWERPC_MPC860)

#if defined(CYG_HAL_POWERPC_MPC823) || defined(CYG_HAL_POWERPC_MPC850)
// Data cache
#define HAL_DCACHE_SIZE                 1024    // Size of data cache in bytes
#define HAL_DCACHE_LINE_SIZE            16      // Size of a data cache line
#define HAL_DCACHE_WAYS                 2       // Associativity of the cache

// Instruction cache
#define HAL_ICACHE_SIZE                 2048    // Size of cache in bytes
#define HAL_ICACHE_LINE_SIZE            16      // Size of a cache line
#define HAL_ICACHE_WAYS                 2       // Associativity of the cache
#endif // defined(CYG_HAL_POWERPC_MPC823) || defined(CYG_HAL_POWERPC_MPC850)

#define HAL_DCACHE_SETS (HAL_DCACHE_SIZE/(HAL_DCACHE_LINE_SIZE*HAL_DCACHE_WAYS))
#define HAL_ICACHE_SETS (HAL_ICACHE_SIZE/(HAL_ICACHE_LINE_SIZE*HAL_ICACHE_WAYS))

//-----------------------------------------------------------------------------
// Global control of data cache

// Enable the data cache
#define HAL_DCACHE_ENABLE()                     \
    asm volatile ("sync;"                       \
                  "mtspr %0, %1;"               \
                  : : "I" (CYGARC_REG_DC_CST), "r" (CYGARC_REG_DC_CMD_CE))

// Disable the data cache
#define HAL_DCACHE_DISABLE()                    \
    asm volatile ("sync;"                       \
                  "mtspr %0, %1;"               \
                  : : "I" (CYGARC_REG_DC_CST), "r" (CYGARC_REG_DC_CMD_CD))

// Invalidate the entire cache
// Note: Any locked lines will not be invalidated.
#define HAL_DCACHE_INVALIDATE_ALL()                     \
    asm volatile ("sync;"                               \
                  "mtspr %0, %1;"                       \
                  : : "I" (CYGARC_REG_DC_CST),          \
                      "r" (CYGARC_REG_DC_CMD_IA))

// Synchronize the contents of the cache with memory.
#define HAL_DCACHE_SYNC()                                                     \
    CYG_MACRO_START                                                           \
    cyg_int32 i;                                                              \
    for (i = 0; i < HAL_DCACHE_SETS; i++){                                    \
        asm volatile ("sync;"                                                 \
                      "mtspr %0, %2;"                                         \