serial5.c

ecos为实时嵌入式操作系统

//==========================================================================
//
//        serial5.c
//
//        Test data duplex receive and send.
//
//==========================================================================
//####COPYRIGHTBEGIN####
//
// -------------------------------------------
// The contents of this file are subject to the Cygnus eCos Public License
// Version 1.0 (the "License"); you may not use this file except in
// compliance with the License.  You may obtain a copy of the License at
// http://sourceware.cygnus.com/ecos
// 
// Software distributed under the License is distributed on an "AS IS"
// basis, WITHOUT WARRANTY OF ANY KIND, either express or implied.  See the
// License for the specific language governing rights and limitations under
// the License.
// 
// The Original Code is eCos - Embedded Cygnus Operating System, released
// September 30, 1998.
// 
// The Initial Developer of the Original Code is Cygnus.  Portions created
// by Cygnus are Copyright (C) 1998, 1999 Cygnus Solutions.  
// All Rights Reserved.
// -------------------------------------------
//
//####COPYRIGHTEND####
//==========================================================================
//#####DESCRIPTIONBEGIN####
//
// Author(s):     jskov
// Contributors:  jskov
// Date:          1999-03-19
// Description:   Test the duplex receive and send capabilities of 
//                the serial driver.
// Requirements:  This test requires the ser_filter on the host side.
//####DESCRIPTIONEND####

#include <pkgconf/system.h>

#include <cyg/infra/testcase.h>         // test macros
#include <cyg/infra/cyg_ass.h>          // assertion macros

#if defined(CYGPKG_IO_SERIAL) && defined(CYGPKG_KERNEL)

#ifdef CYGPKG_KERNEL
#include <pkgconf/kernel.h>
#ifdef CYGFUN_KERNEL_API_C
#include <cyg/hal/hal_arch.h>           // CYGNUM_HAL_STACK_SIZE_TYPICAL
#include <cyg/kernel/kapi.h>
unsigned char stack[CYGNUM_HAL_STACK_SIZE_TYPICAL];
cyg_thread thread_data;
cyg_handle_t thread_handle;
#endif
#endif

#include "ser_test_protocol.inl"

//---------------------------------------------------------------------------
// Serial test main function.
void
serial_test( void )
{
    cyg_io_handle_t ser_handle;

    test_open_ser(&ser_handle);

    // We need the filter for this test.
    test_ping(ser_handle);

#if defined(CYGPKG_HAL_ARM_AEB)
    {
        // The AEB board is too slow to run the driver in interrupt mode
        // at the default 38400 baud when doing this test.
        cyg_ser_cfg_t arm_aeb_cfg = { 
            CYGNUM_SERIAL_BAUD_9600, CYGNUM_SERIAL_WORD_LENGTH_8, 
            CYGNUM_SERIAL_STOP_1, CYGNUM_SERIAL_PARITY_NONE };

        change_config(ser_handle, &arm_aeb_cfg);
    }
#endif

    // Start out slow, then go for many tests. Each cycle causes
    // 512 bytes to be sent over the wire.
    test_binary(ser_handle,    1, MODE_DUPLEX_ECHO);
    test_binary(ser_handle,    2, MODE_DUPLEX_ECHO);
    test_binary(ser_handle,    5, MODE_DUPLEX_ECHO);

#if 0 // Disable these until the ser_filter produces status output.
    test_binary(ser_handle,  128, MODE_DUPLEX_ECHO);
    test_binary(ser_handle,  512, MODE_DUPLEX_ECHO);
    test_binary(ser_handle, 1024, MODE_DUPLEX_ECHO);
#endif

    CYG_TEST_PASS_FINISH("serial5 test OK");
}

void
cyg_start(void)
{
    CYG_TEST_INIT();
#ifdef CYGFUN_KERNEL_API_C
    cyg_thread_create(10,                   // Priority - just a number
                      (cyg_thread_entry_t*)serial_test,         // entry
                      0,                    // 
                      "serial_thread",     // Name
                      &stack[0],            // Stack
                      CYGNUM_HAL_STACK_SIZE_TYPICAL,           // Size
                      &thread_handle,       // Handle
                      &thread_data          // Thread data structure
        );
    cyg_thread_resume(thread_handle);
    cyg_scheduler_start();
#else
    serial_test();
#endif
}

#else // ifdef CYGPKG_IO_SERIAL

void
cyg_start(void)
{
    CYG_TEST_INIT();
    CYG_TEST_NA("Requires serial device driver and kernel");
}

#endif
// EOF serial5.c