config.h

kedin bsp for vxWorks

/* config.h - KS8695P demo board configuration header */



/*
modification history
--------------------
9/15/2003  Ritter Yeh  created 
*/

/*
This module contains the configuration parameters for the KS8695P demo board BSP.
*/

#ifndef	INCconfigh
#define	INCconfigh

#ifdef __cplusplus
extern "C" {
#endif



/* BSP version/revision identification, before configAll.h */

#define BSP_VERSION	"1.0"
#define BSP_REV		"/0"	/* 0 for first revision */

#include "configAll.h"

/*
 * STANDALONE_NET must be defined for network debug with
 * standalone vxWorks
 */
#undef STANDALONE_NET

/*
 * Define SERIAL_DEBUG to enable debugging
 * via the serial ports
 */
#undef SERIAL_DEBUG


#define DEFAULT_BOOT_LINE \
    "ks(0,0) host:vxWorks " \
    "h=10.0.0.3 e=10.0.0.50:ffffff00 u=target tn=ks8695p"





/* Memory configuration */

#undef	LOCAL_MEM_AUTOSIZE			/* run-time memory sizing */
#define USER_RESERVED_MEM	0		/* see sysMemTop() */

/*
 * Local-to-Bus memory address constants:
 * the local memory address always appears at 0 locally;
 * it is not dual ported.
 */


#define LOCAL_MEM_LOCAL_ADRS	0x00000000	/* fixed at zero */
#define LOCAL_MEM_BUS_ADRS	0x00000000	/* fixed at zero */
#define LOCAL_MEM_SIZE		0x02000000	/* 32 Mbytes */

#define LOCAL_MEM_END_ADRS	(LOCAL_MEM_LOCAL_ADRS + LOCAL_MEM_SIZE)


/*
 * Boot ROM is an image written into Flash. Part of the Flash can be
 * reserved for boot parameters etc. (see the Flash section below).
 *
 * The following parameters are defined here and in the Makefile.
 * They must be kept synchronized; effectively config.h depends on Makefile.
 * Any changes made here must be made in the Makefile and vice versa.
 *
 * ROM_BASE_ADRS is the base of the Flash ROM/EPROM.
 * ROM_TEXT_ADRS is the entry point of the VxWorks image
 * ROM_SIZE is the size of the part of the Flash ROM/EPROM allocated to
 *		the VxWorks image (block size - size of headers)
 *
 * Two other constants are used:
 * ROM_COPY_SIZE is the size of the part of the ROM to be copied into RAM
 * 		 (e.g. in uncompressed boot ROM)
 * ROM_SIZE_TOTAL is the size of the entire Flash ROM (used in sysPhysMemDesc)
 *
 * The values are given as literals here to make it easier to ensure
 * that they are the same as those in the Makefile.
 */

#define ROM_BASE_ADRS       0x02800000     /* base of Flash/EPROM */
#define ROM_TEXT_ADRS       ROM_BASE_ADRS  /* code start addr in ROM */
#define ROM_SIZE            0x00100000     /* size of ROM holding VxWorks*/

#define ROM_COPY_SIZE       ROM_SIZE
#define ROM_SIZE_TOTAL      0x00400000	/* total size of ROM */


#define RAM_LOW_ADRS	    0x00001000	/* VxWorks image entry point */
#define RAM_HIGH_ADRS	    0x00600000	/* RAM address for ROM boot */




/*
 * Flash/NVRAM memory configuration
 *
 * A block of the Flash memory (FLASH_SIZE bytes at FLASH_ADRS) is
 * reserved for non-volatile storage of data.
 *
 * See also integrator.h
 */

#define INCLUDE_FLASH

#ifdef INCLUDE_FLASH
#define FLASH_SIZE		0x00010000	/* one 64kbyte block of Flash*/
#define NV_RAM_SIZE		0x100		/* how much we use as NVRAM */
#undef	NV_BOOT_OFFSET
#define NV_BOOT_OFFSET		0		/* bootline at start of NVRAM */
#define FLASH_NO_OVERLAY			/* do not read-modify-write all
						 * of Flash */
#define INCLUDE_FLASH_SIB_FOOTER		/* add a SIB footer to block */
#else	/* INCLUDE_FLASH */
#define NV_RAM_SIZE		NONE

#endif	/* INCLUDE_FLASH */


/* Serial port configuration */

#define INCLUDE_SERIAL
#undef	NUM_TTY
#define NUM_TTY			N_SIO_CHANNELS
/*
 * Define SERIAL_DEBUG to enable debugging
 * via the serial ports
 */
 #undef SERIAL_DEBUG
 #ifdef SERIAL_DEBUG
  #define WDB_NO_BAUD_AUTO_CONFIG

  #undef WDB_COMM_TYPE
  #undef WDB_TTY_BAUD
  #undef WDB_TTY_CHANNEL
  #undef WDB_TTY_DEV_NAME

  #define WDB_COMM_TYPE       WDB_COMM_SERIAL /* WDB in Serial mode */
  #define WDB_TTY_BAUD        38400          /* Baud rate for WDB Connection */
  #define WDB_TTY_CHANNEL     1               /* COM PORT #2 */
  #define WDB_TTY_DEV_NAME    "/tyCo/1"       /* default TYCODRV_5_2 device name */
 #endif /* SERIAL_DEBUG */



/*
 * We use the generic architecture libraries, with caches/MMUs present. A
 * call to sysHwInit0() is needed from within usrInit before
 * cacheLibInit() is called.
 */

#ifndef _ASMLANGUAGE
IMPORT void sysHwInit0 (void);
#endif
#define INCLUDE_SYS_HW_INIT_0
#define SYS_HW_INIT_0()         sysHwInit0 ()


/*
 * Cache/MMU configuration
 *
 * Note that when MMU is enabled, cache modes are controlled by
 * the MMU table entries in sysPhysMemDesc[], not the cache mode
 * macros defined here.
 */

#undef  USER_I_CACHE_MODE
#define USER_I_CACHE_MODE       CACHE_WRITETHROUGH

#undef  USER_D_CACHE_MODE
#define USER_D_CACHE_MODE       CACHE_DISABLED


/*
 * Include MMU BASIC and CACHE support for command line and project builds
 */
#define	 INCLUDE_MMU_BASIC
#define  INCLUDE_CACHE_SUPPORT



/*
 * Network driver configuration.
 *
 * De-select unused (default) network drivers selected in configAll.h.
 */

#undef	INCLUDE_ENP		/* include CMC Ethernet interface*/
#undef	INCLUDE_EX		/* include Excelan Ethernet interface */
#undef	INCLUDE_SM_NET		/* include backplane net interface */
#undef	INCLUDE_SM_SEQ_ADDR	/* shared memory network auto address setup */

/* Enhanced Network Driver (END) Support */

#define INCLUDE_END

#ifdef	INCLUDE_END
#undef INCLUDE_DEC21X40END	/* include PCI-based DEC 21X4X END Ethernet */
#undef INCLUDE_FEI82557END	/* include PCI-based Intel END Ethernet */

#ifndef SERIAL_DEBUG
#undef  WDB_COMM_TYPE		/* WDB agent communication path is END */
#define WDB_COMM_TYPE	WDB_COMM_END
#define WBD_AGENT_END
#else
#undef WBD_AGENT_END
#endif /* SERIAL_DEBUG */

#ifdef INCLUDE_DEC21X40END
#define INCLUDE_MIILIB
#endif

#endif  /* INCLUDE_END */


/* PCI configuration */

#define INCLUDE_PCI
#define INCLUDE_SHOW_ROUTINES

/*
 * Interrupt mode - interrupts can be in either preemptive or non-preemptive
 * mode.  For non-preemptive mode, change INT_MODE to INT_NON_PREEMPT_MODEL
 */

#define INT_MODE	INT_PREEMPT_MODEL



/*
 * miscellaneous definitions
 * Note: ISR_STACK_SIZE is defined here rather than in ../all/configAll.h
 * (as is more usual) because the stack size depends on the interrupt
 * structure of the BSP.
 */

#define ISR_STACK_SIZE	0x800	/* size of ISR stack, in bytes */


/* Optional timestamp support */

#undef	INCLUDE_TIMESTAMP	/* define to include timestamp driver */
#define INCLUDE_TIMESTAMP


/* Optional TrueFFS support */

#undef	INCLUDE_TFFS		/* define to include TrueFFS driver */

#ifdef INCLUDE_TFFS
#define INCLUDE_SHOW_ROUTINES
#define INCLUDE_DOSFS
#endif /* INCLUDE_TFFS */

#include "ks8695p.h"

#undef BSP_VTS
#ifdef BSP_VTS
/***************************************************
 * Add these defines for the Validation Test Suite *
 ***************************************************/
#define INCLUDE_SHELL
#define INCLUDE_RLOGIN
#define INCLUDE_SHOW_ROUTINES
#define INCLUDE_NET_SYM_TBL
#define INCLUDE_LOADER

#define INCLUDE_PING
#define INCLUDE_NET_SHOW
#endif /*BSP_VTS*/

#undef INCLUDE_WINDML          /* define to include windML support */

#ifdef __cplusplus
}
#endif
#endif  /* INCconfigh */

#if defined(PRJ_BUILD)
#include "prjParams.h"
#endif