📄 8390.c
字号:
ei_block_output(dev, length, skb->data, ei_local->tx_start_page); ei_local->txing = 1; NS8390_trigger_send(dev, send_length, ei_local->tx_start_page); dev->trans_start = jiffies; dev->tbusy = 1;#endif /* EI_PINGPONG */ /* Turn 8390 interrupts back on. */ ei_local->irqlock = 0; outb_p(ENISR_ALL, e8390_base + EN0_IMR); spin_unlock(&ei_local->page_lock); enable_irq(dev->irq); dev_kfree_skb (skb); ei_local->stat.tx_bytes += send_length; return 0;}/* The typical workload of the driver: Handle the ether interface interrupts. */void ei_interrupt(int irq, void *dev_id, struct pt_regs * regs){ struct device *dev = dev_id; int e8390_base; int interrupts, nr_serviced = 0; struct ei_device *ei_local; if (dev == NULL) { printk ("net_interrupt(): irq %d for unknown device.\n", irq); return; } e8390_base = dev->base_addr; ei_local = (struct ei_device *) dev->priv; /* * Protect the irq test too. */ spin_lock(&ei_local->page_lock); if (dev->interrupt || ei_local->irqlock) {#if 1 /* This might just be an interrupt for a PCI device sharing this line */ /* The "irqlock" check is only for testing. */ printk(ei_local->irqlock ? "%s: Interrupted while interrupts are masked! isr=%#2x imr=%#2x.\n" : "%s: Reentering the interrupt handler! isr=%#2x imr=%#2x.\n", dev->name, inb_p(e8390_base + EN0_ISR), inb_p(e8390_base + EN0_IMR));#endif spin_unlock(&ei_local->page_lock); return; } dev->interrupt = 1; /* Change to page 0 and read the intr status reg. */ outb_p(E8390_NODMA+E8390_PAGE0, e8390_base + E8390_CMD); if (ei_debug > 3) printk(KERN_DEBUG "%s: interrupt(isr=%#2.2x).\n", dev->name, inb_p(e8390_base + EN0_ISR)); /* !!Assumption!! -- we stay in page 0. Don't break this. */ while ((interrupts = inb_p(e8390_base + EN0_ISR)) != 0 && ++nr_serviced < MAX_SERVICE) { if (dev->start == 0) { printk(KERN_WARNING "%s: interrupt from stopped card\n", dev->name); interrupts = 0; break; } if (interrupts & ENISR_OVER) ei_rx_overrun(dev); else if (interrupts & (ENISR_RX+ENISR_RX_ERR)) { /* Got a good (?) packet. */ ei_receive(dev); } /* Push the next to-transmit packet through. */ if (interrupts & ENISR_TX) ei_tx_intr(dev); else if (interrupts & ENISR_TX_ERR) ei_tx_err(dev); if (interrupts & ENISR_COUNTERS) { ei_local->stat.rx_frame_errors += inb_p(e8390_base + EN0_COUNTER0); ei_local->stat.rx_crc_errors += inb_p(e8390_base + EN0_COUNTER1); ei_local->stat.rx_missed_errors+= inb_p(e8390_base + EN0_COUNTER2); outb_p(ENISR_COUNTERS, e8390_base + EN0_ISR); /* Ack intr. */ } /* Ignore any RDC interrupts that make it back to here. */ if (interrupts & ENISR_RDC) { outb_p(ENISR_RDC, e8390_base + EN0_ISR); } outb_p(E8390_NODMA+E8390_PAGE0+E8390_START, e8390_base + E8390_CMD); } if (interrupts && ei_debug) { outb_p(E8390_NODMA+E8390_PAGE0+E8390_START, e8390_base + E8390_CMD); if (nr_serviced >= MAX_SERVICE) { printk(KERN_WARNING "%s: Too much work at interrupt, status %#2.2x\n", dev->name, interrupts); outb_p(ENISR_ALL, e8390_base + EN0_ISR); /* Ack. most intrs. */ } else { printk(KERN_WARNING "%s: unknown interrupt %#2x\n", dev->name, interrupts); outb_p(0xff, e8390_base + EN0_ISR); /* Ack. all intrs. */ } } dev->interrupt = 0; spin_unlock(&ei_local->page_lock); return;}/* * A transmitter error has happened. Most likely excess collisions (which * is a fairly normal condition). If the error is one where the Tx will * have been aborted, we try and send another one right away, instead of * letting the failed packet sit and collect dust in the Tx buffer. This * is a much better solution as it avoids kernel based Tx timeouts, and * an unnecessary card reset. * * Called with lock held */static void ei_tx_err(struct device *dev){ int e8390_base = dev->base_addr; struct ei_device *ei_local = (struct ei_device *) dev->priv; unsigned char txsr = inb_p(e8390_base+EN0_TSR); unsigned char tx_was_aborted = txsr & (ENTSR_ABT+ENTSR_FU);#ifdef VERBOSE_ERROR_DUMP printk(KERN_DEBUG "%s: transmitter error (%#2x): ", dev->name, txsr); if (txsr & ENTSR_ABT) printk("excess-collisions "); if (txsr & ENTSR_ND) printk("non-deferral "); if (txsr & ENTSR_CRS) printk("lost-carrier "); if (txsr & ENTSR_FU) printk("FIFO-underrun "); if (txsr & ENTSR_CDH) printk("lost-heartbeat "); printk("\n");#endif outb_p(ENISR_TX_ERR, e8390_base + EN0_ISR); /* Ack intr. */ if (tx_was_aborted) ei_tx_intr(dev); else { ei_local->stat.tx_errors++; if (txsr & ENTSR_CRS) ei_local->stat.tx_carrier_errors++; if (txsr & ENTSR_CDH) ei_local->stat.tx_heartbeat_errors++; if (txsr & ENTSR_OWC) ei_local->stat.tx_window_errors++; }}/* We have finished a transmit: check for errors and then trigger the next packet to be sent. Called with lock held */static void ei_tx_intr(struct device *dev){ int e8390_base = dev->base_addr; struct ei_device *ei_local = (struct ei_device *) dev->priv; int status = inb(e8390_base + EN0_TSR); outb_p(ENISR_TX, e8390_base + EN0_ISR); /* Ack intr. */#ifdef EI_PINGPONG /* * There are two Tx buffers, see which one finished, and trigger * the send of another one if it exists. */ ei_local->txqueue--; if (ei_local->tx1 < 0) { if (ei_local->lasttx != 1 && ei_local->lasttx != -1) printk(KERN_ERR "%s: bogus last_tx_buffer %d, tx1=%d.\n", ei_local->name, ei_local->lasttx, ei_local->tx1); ei_local->tx1 = 0; dev->tbusy = 0; if (ei_local->tx2 > 0) { ei_local->txing = 1; NS8390_trigger_send(dev, ei_local->tx2, ei_local->tx_start_page + 6); dev->trans_start = jiffies; ei_local->tx2 = -1, ei_local->lasttx = 2; } else ei_local->lasttx = 20, ei_local->txing = 0; } else if (ei_local->tx2 < 0) { if (ei_local->lasttx != 2 && ei_local->lasttx != -2) printk("%s: bogus last_tx_buffer %d, tx2=%d.\n", ei_local->name, ei_local->lasttx, ei_local->tx2); ei_local->tx2 = 0; dev->tbusy = 0; if (ei_local->tx1 > 0) { ei_local->txing = 1; NS8390_trigger_send(dev, ei_local->tx1, ei_local->tx_start_page); dev->trans_start = jiffies; ei_local->tx1 = -1; ei_local->lasttx = 1; } else ei_local->lasttx = 10, ei_local->txing = 0; } else printk(KERN_WARNING "%s: unexpected TX-done interrupt, lasttx=%d.\n", dev->name, ei_local->lasttx);#else /* EI_PINGPONG */ /* * Single Tx buffer: mark it free so another packet can be loaded. */ ei_local->txing = 0; dev->tbusy = 0;#endif /* Minimize Tx latency: update the statistics after we restart TXing. */ if (status & ENTSR_COL) ei_local->stat.collisions++; if (status & ENTSR_PTX) ei_local->stat.tx_packets++; else { ei_local->stat.tx_errors++; if (status & ENTSR_ABT) { ei_local->stat.tx_aborted_errors++; ei_local->stat.collisions += 16; } if (status & ENTSR_CRS) ei_local->stat.tx_carrier_errors++; if (status & ENTSR_FU) ei_local->stat.tx_fifo_errors++; if (status & ENTSR_CDH) ei_local->stat.tx_heartbeat_errors++; if (status & ENTSR_OWC) ei_local->stat.tx_window_errors++; } mark_bh (NET_BH);}/* We have a good packet(s), get it/them out of the buffers. Called with lock held */static void ei_receive(struct device *dev){ int e8390_base = dev->base_addr; struct ei_device *ei_local = (struct ei_device *) dev->priv; unsigned char rxing_page, this_frame, next_frame; unsigned short current_offset; int rx_pkt_count = 0; struct e8390_pkt_hdr rx_frame; int num_rx_pages = ei_local->stop_page-ei_local->rx_start_page; while (++rx_pkt_count < 10) { int pkt_len, pkt_stat; /* Get the rx page (incoming packet pointer). */ outb_p(E8390_NODMA+E8390_PAGE1, e8390_base + E8390_CMD); rxing_page = inb_p(e8390_base + EN1_CURPAG); outb_p(E8390_NODMA+E8390_PAGE0, e8390_base + E8390_CMD); /* Remove one frame from the ring. Boundary is always a page behind. */ this_frame = inb_p(e8390_base + EN0_BOUNDARY) + 1; if (this_frame >= ei_local->stop_page) this_frame = ei_local->rx_start_page; /* Someday we'll omit the previous, iff we never get this message. (There is at least one clone claimed to have a problem.) */ if (ei_debug > 0 && this_frame != ei_local->current_page) printk(KERN_ERR "%s: mismatched read page pointers %2x vs %2x.\n", dev->name, this_frame, ei_local->current_page); if (this_frame == rxing_page) /* Read all the frames? */ break; /* Done for now */ current_offset = this_frame << 8; ei_get_8390_hdr(dev, &rx_frame, this_frame); pkt_len = rx_frame.count - sizeof(struct e8390_pkt_hdr); pkt_stat = rx_frame.status; next_frame = this_frame + 1 + ((pkt_len+4)>>8); /* Check for bogosity warned by 3c503 book: the status byte is never written. This happened a lot during testing! This code should be cleaned up someday. */ if (rx_frame.next != next_frame && rx_frame.next != next_frame + 1 && rx_frame.next != next_frame - num_rx_pages && rx_frame.next != next_frame + 1 - num_rx_pages) { ei_local->current_page = rxing_page; outb(ei_local->current_page-1, e8390_base+EN0_BOUNDARY); ei_local->stat.rx_errors++; continue; } if (pkt_len < 60 || pkt_len > 1518) { if (ei_debug) printk(KERN_DEBUG "%s: bogus packet size: %d, status=%#2x nxpg=%#2x.\n", dev->name, rx_frame.count, rx_frame.status, rx_frame.next); ei_local->stat.rx_errors++; ei_local->stat.rx_length_errors++; } else if ((pkt_stat & 0x0F) == ENRSR_RXOK) { struct sk_buff *skb; skb = dev_alloc_skb(pkt_len+2); if (skb == NULL) { if (ei_debug > 1) printk(KERN_DEBUG "%s: Couldn't allocate a sk_buff of size %d.\n", dev->name, pkt_len); ei_local->stat.rx_dropped++; break; } else { skb_reserve(skb,2); /* IP headers on 16 byte boundaries */ skb->dev = dev; skb_put(skb, pkt_len); /* Make room */ ei_block_input(dev, pkt_len, skb, current_offset + sizeof(rx_frame)); skb->protocol=eth_type_trans(skb,dev); netif_rx(skb); ei_local->stat.rx_packets++; ei_local->stat.rx_bytes += pkt_len; if (pkt_stat & ENRSR_PHY) ei_local->stat.multicast++; } } else { if (ei_debug) printk(KERN_DEBUG "%s: bogus packet: status=%#2x nxpg=%#2x size=%d\n", dev->name, rx_frame.status, rx_frame.next, rx_frame.count); ei_local->stat.rx_errors++; /* NB: The NIC counts CRC, frame and missed errors. */ if (pkt_stat & ENRSR_FO) ei_local->stat.rx_fifo_errors++; } next_frame = rx_frame.next; /* This _should_ never happen: it's here for avoiding bad clones. */ if (next_frame >= ei_local->stop_page) { printk("%s: next frame inconsistency, %#2x\n", dev->name, next_frame); next_frame = ei_local->rx_start_page; } ei_local->current_page = next_frame; outb_p(next_frame-1, e8390_base+EN0_BOUNDARY); } /* We used to also ack ENISR_OVER here, but that would sometimes mask
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -