e1000_hw.h

linux下从网卡远程启动

/* Receive Descriptor Control */
#define E1000_RXDCTL_PTHRESH 0x0000003F /* RXDCTL Prefetch Threshold */
#define E1000_RXDCTL_HTHRESH 0x00003F00 /* RXDCTL Host Threshold */
#define E1000_RXDCTL_WTHRESH 0x003F0000 /* RXDCTL Writeback Threshold */
#define E1000_RXDCTL_GRAN    0x01000000 /* RXDCTL Granularity */

/* Transmit Descriptor Control */
#define E1000_TXDCTL_PTHRESH 0x000000FF /* TXDCTL Prefetch Threshold */
#define E1000_TXDCTL_HTHRESH 0x0000FF00 /* TXDCTL Host Threshold */
#define E1000_TXDCTL_WTHRESH 0x00FF0000 /* TXDCTL Writeback Threshold */
#define E1000_TXDCTL_GRAN    0x01000000 /* TXDCTL Granularity */
#define E1000_TXDCTL_LWTHRESH 0xFE000000 /* TXDCTL Low Threshold */
#define E1000_TXDCTL_FULL_TX_DESC_WB 0x01010000 /* GRAN=1, WTHRESH=1 */

/* Transmit Configuration Word */
#define E1000_TXCW_FD         0x00000020        /* TXCW full duplex */
#define E1000_TXCW_HD         0x00000040        /* TXCW half duplex */
#define E1000_TXCW_PAUSE      0x00000080        /* TXCW sym pause request */
#define E1000_TXCW_ASM_DIR    0x00000100        /* TXCW astm pause direction */
#define E1000_TXCW_PAUSE_MASK 0x00000180        /* TXCW pause request mask */
#define E1000_TXCW_RF         0x00003000        /* TXCW remote fault */
#define E1000_TXCW_NP         0x00008000        /* TXCW next page */
#define E1000_TXCW_CW         0x0000ffff        /* TxConfigWord mask */
#define E1000_TXCW_TXC        0x40000000        /* Transmit Config control */
#define E1000_TXCW_ANE        0x80000000        /* Auto-neg enable */

/* Receive Configuration Word */
#define E1000_RXCW_CW    0x0000ffff     /* RxConfigWord mask */
#define E1000_RXCW_NC    0x04000000     /* Receive config no carrier */
#define E1000_RXCW_IV    0x08000000     /* Receive config invalid */
#define E1000_RXCW_CC    0x10000000     /* Receive config change */
#define E1000_RXCW_C     0x20000000     /* Receive config */
#define E1000_RXCW_SYNCH 0x40000000     /* Receive config synch */
#define E1000_RXCW_ANC   0x80000000     /* Auto-neg complete */

/* Transmit Control */
#define E1000_TCTL_RST    0x00000001    /* software reset */
#define E1000_TCTL_EN     0x00000002    /* enable tx */
#define E1000_TCTL_BCE    0x00000004    /* busy check enable */
#define E1000_TCTL_PSP    0x00000008    /* pad short packets */
#define E1000_TCTL_CT     0x00000ff0    /* collision threshold */
#define E1000_TCTL_COLD   0x003ff000    /* collision distance */
#define E1000_TCTL_SWXOFF 0x00400000    /* SW Xoff transmission */
#define E1000_TCTL_PBE    0x00800000    /* Packet Burst Enable */
#define E1000_TCTL_RTLC   0x01000000    /* Re-transmit on late collision */
#define E1000_TCTL_NRTU   0x02000000    /* No Re-transmit on underrun */

/* Receive Checksum Control */
#define E1000_RXCSUM_PCSS_MASK 0x000000FF   /* Packet Checksum Start */
#define E1000_RXCSUM_IPOFL     0x00000100   /* IPv4 checksum offload */
#define E1000_RXCSUM_TUOFL     0x00000200   /* TCP / UDP checksum offload */
#define E1000_RXCSUM_IPV6OFL   0x00000400   /* IPv6 checksum offload */

/* Definitions for power management and wakeup registers */
/* Wake Up Control */
#define E1000_WUC_APME       0x00000001 /* APM Enable */
#define E1000_WUC_PME_EN     0x00000002 /* PME Enable */
#define E1000_WUC_PME_STATUS 0x00000004 /* PME Status */
#define E1000_WUC_APMPME     0x00000008 /* Assert PME on APM Wakeup */
#define E1000_WUC_SPM        0x80000000 /* Enable SPM */

/* Wake Up Filter Control */
#define E1000_WUFC_LNKC 0x00000001 /* Link Status Change Wakeup Enable */
#define E1000_WUFC_MAG  0x00000002 /* Magic Packet Wakeup Enable */
#define E1000_WUFC_EX   0x00000004 /* Directed Exact Wakeup Enable */
#define E1000_WUFC_MC   0x00000008 /* Directed Multicast Wakeup Enable */
#define E1000_WUFC_BC   0x00000010 /* Broadcast Wakeup Enable */
#define E1000_WUFC_ARP  0x00000020 /* ARP Request Packet Wakeup Enable */
#define E1000_WUFC_IPV4 0x00000040 /* Directed IPv4 Packet Wakeup Enable */
#define E1000_WUFC_IPV6 0x00000080 /* Directed IPv6 Packet Wakeup Enable */
#define E1000_WUFC_FLX0 0x00010000 /* Flexible Filter 0 Enable */
#define E1000_WUFC_FLX1 0x00020000 /* Flexible Filter 1 Enable */
#define E1000_WUFC_FLX2 0x00040000 /* Flexible Filter 2 Enable */
#define E1000_WUFC_FLX3 0x00080000 /* Flexible Filter 3 Enable */
#define E1000_WUFC_ALL_FILTERS 0x000F00FF /* Mask for all wakeup filters */
#define E1000_WUFC_FLX_OFFSET 16       /* Offset to the Flexible Filters bits */
#define E1000_WUFC_FLX_FILTERS 0x000F0000 /* Mask for the 4 flexible filters */

/* Wake Up Status */
#define E1000_WUS_LNKC 0x00000001 /* Link Status Changed */
#define E1000_WUS_MAG  0x00000002 /* Magic Packet Received */
#define E1000_WUS_EX   0x00000004 /* Directed Exact Received */
#define E1000_WUS_MC   0x00000008 /* Directed Multicast Received */
#define E1000_WUS_BC   0x00000010 /* Broadcast Received */
#define E1000_WUS_ARP  0x00000020 /* ARP Request Packet Received */
#define E1000_WUS_IPV4 0x00000040 /* Directed IPv4 Packet Wakeup Received */
#define E1000_WUS_IPV6 0x00000080 /* Directed IPv6 Packet Wakeup Received */
#define E1000_WUS_FLX0 0x00010000 /* Flexible Filter 0 Match */
#define E1000_WUS_FLX1 0x00020000 /* Flexible Filter 1 Match */
#define E1000_WUS_FLX2 0x00040000 /* Flexible Filter 2 Match */
#define E1000_WUS_FLX3 0x00080000 /* Flexible Filter 3 Match */
#define E1000_WUS_FLX_FILTERS 0x000F0000 /* Mask for the 4 flexible filters */

/* Management Control */
#define E1000_MANC_SMBUS_EN      0x00000001 /* SMBus Enabled - RO */
#define E1000_MANC_ASF_EN        0x00000002 /* ASF Enabled - RO */
#define E1000_MANC_R_ON_FORCE    0x00000004 /* Reset on Force TCO - RO */
#define E1000_MANC_RMCP_EN       0x00000100 /* Enable RCMP 026Fh Filtering */
#define E1000_MANC_0298_EN       0x00000200 /* Enable RCMP 0298h Filtering */
#define E1000_MANC_IPV4_EN       0x00000400 /* Enable IPv4 */
#define E1000_MANC_IPV6_EN       0x00000800 /* Enable IPv6 */
#define E1000_MANC_SNAP_EN       0x00001000 /* Accept LLC/SNAP */
#define E1000_MANC_ARP_EN        0x00002000 /* Enable ARP Request Filtering */
#define E1000_MANC_NEIGHBOR_EN   0x00004000 /* Enable Neighbor Discovery 
                                             * Filtering */
#define E1000_MANC_TCO_RESET     0x00010000 /* TCO Reset Occurred */
#define E1000_MANC_RCV_TCO_EN    0x00020000 /* Receive TCO Packets Enabled */
#define E1000_MANC_REPORT_STATUS 0x00040000 /* Status Reporting Enabled */
#define E1000_MANC_SMB_REQ       0x01000000 /* SMBus Request */
#define E1000_MANC_SMB_GNT       0x02000000 /* SMBus Grant */
#define E1000_MANC_SMB_CLK_IN    0x04000000 /* SMBus Clock In */
#define E1000_MANC_SMB_DATA_IN   0x08000000 /* SMBus Data In */
#define E1000_MANC_SMB_DATA_OUT  0x10000000 /* SMBus Data Out */
#define E1000_MANC_SMB_CLK_OUT   0x20000000 /* SMBus Clock Out */

#define E1000_MANC_SMB_DATA_OUT_SHIFT  28 /* SMBus Data Out Shift */
#define E1000_MANC_SMB_CLK_OUT_SHIFT   29 /* SMBus Clock Out Shift */

/* Wake Up Packet Length */
#define E1000_WUPL_LENGTH_MASK 0x0FFF   /* Only the lower 12 bits are valid */

#define E1000_MDALIGN          4096

/* EEPROM Commands - Microwire */
#define EEPROM_READ_OPCODE_MICROWIRE  0x6  /* EEPROM read opcode */
#define EEPROM_WRITE_OPCODE_MICROWIRE 0x5  /* EEPROM write opcode */
#define EEPROM_ERASE_OPCODE_MICROWIRE 0x7  /* EEPROM erase opcode */
#define EEPROM_EWEN_OPCODE_MICROWIRE  0x13 /* EEPROM erase/write enable */
#define EEPROM_EWDS_OPCODE_MICROWIRE  0x10 /* EEPROM erast/write disable */

/* EEPROM Commands - SPI */
#define EEPROM_MAX_RETRY_SPI    5000 /* Max wait of 5ms, for RDY signal */
#define EEPROM_READ_OPCODE_SPI  0x3  /* EEPROM read opcode */
#define EEPROM_WRITE_OPCODE_SPI 0x2  /* EEPROM write opcode */
#define EEPROM_A8_OPCODE_SPI    0x8  /* opcode bit-3 = address bit-8 */
#define EEPROM_WREN_OPCODE_SPI  0x6  /* EEPROM set Write Enable latch */
#define EEPROM_WRDI_OPCODE_SPI  0x4  /* EEPROM reset Write Enable latch */
#define EEPROM_RDSR_OPCODE_SPI  0x5  /* EEPROM read Status register */
#define EEPROM_WRSR_OPCODE_SPI  0x1  /* EEPROM write Status register */

/* EEPROM Size definitions */
#define EEPROM_SIZE_16KB        0x1800
#define EEPROM_SIZE_8KB         0x1400
#define EEPROM_SIZE_4KB         0x1000
#define EEPROM_SIZE_2KB         0x0C00
#define EEPROM_SIZE_1KB         0x0800
#define EEPROM_SIZE_512B        0x0400
#define EEPROM_SIZE_128B        0x0000
#define EEPROM_SIZE_MASK        0x1C00

/* EEPROM Word Offsets */
#define EEPROM_COMPAT              0x0003
#define EEPROM_ID_LED_SETTINGS     0x0004
#define EEPROM_SERDES_AMPLITUDE       0x0006 /* For SERDES output amplitude adjustment. */
#define EEPROM_INIT_CONTROL1_REG   0x000A
#define EEPROM_INIT_CONTROL2_REG   0x000F
#define EEPROM_INIT_CONTROL3_PORT_B   0x0014
#define EEPROM_INIT_CONTROL3_PORT_A   0x0024
#define EEPROM_CFG                 0x0012
#define EEPROM_FLASH_VERSION       0x0032
#define EEPROM_CHECKSUM_REG        0x003F

/* Word definitions for ID LED Settings */
#define ID_LED_RESERVED_0000 0x0000
#define ID_LED_RESERVED_FFFF 0xFFFF
#define ID_LED_DEFAULT       ((ID_LED_OFF1_ON2 << 12) | \
                              (ID_LED_OFF1_OFF2 << 8) | \
                              (ID_LED_DEF1_DEF2 << 4) | \
                              (ID_LED_DEF1_DEF2))
#define ID_LED_DEF1_DEF2     0x1
#define ID_LED_DEF1_ON2      0x2
#define ID_LED_DEF1_OFF2     0x3
#define ID_LED_ON1_DEF2      0x4
#define ID_LED_ON1_ON2       0x5
#define ID_LED_ON1_OFF2      0x6
#define ID_LED_OFF1_DEF2     0x7
#define ID_LED_OFF1_ON2      0x8
#define ID_LED_OFF1_OFF2     0x9

#define IGP_ACTIVITY_LED_MASK   0xFFFFF0FF
#define IGP_ACTIVITY_LED_ENABLE 0x0300
#define IGP_LED3_MODE           0x07000000


/* Mask bits for SERDES amplitude adjustment in Word 6 of the EEPROM */
#define EEPROM_SERDES_AMPLITUDE_MASK  0x000F

/* Mask bits for fields in Word 0x0a of the EEPROM */
#define EEPROM_WORD0A_ILOS   0x0010
#define EEPROM_WORD0A_SWDPIO 0x01E0
#define EEPROM_WORD0A_LRST   0x0200
#define EEPROM_WORD0A_FD     0x0400
#define EEPROM_WORD0A_66MHZ  0x0800

/* Mask bits for fields in Word 0x0f of the EEPROM */
#define EEPROM_WORD0F_PAUSE_MASK 0x3000
#define EEPROM_WORD0F_PAUSE      0x1000
#define EEPROM_WORD0F_ASM_DIR    0x2000
#define EEPROM_WORD0F_ANE        0x0800
#define EEPROM_WORD0F_SWPDIO_EXT 0x00F0

/* For checksumming, the sum of all words in the EEPROM should equal 0xBABA. */
#define EEPROM_SUM 0xBABA

/* EEPROM Map defines (WORD OFFSETS)*/
#define EEPROM_NODE_ADDRESS_BYTE_0 0
#define EEPROM_PBA_BYTE_1          8

#define EEPROM_RESERVED_WORD          0xFFFF

/* EEPROM Map Sizes (Byte Counts) */
#define PBA_SIZE 4

/* Collision related configuration parameters */
#define E1000_COLLISION_THRESHOLD       16
#define E1000_CT_SHIFT                  4
#define E1000_COLLISION_DISTANCE        64
#define E1000_FDX_COLLISION_DISTANCE    E1000_COLLISION_DISTANCE
#define E1000_HDX_COLLISION_DISTANCE    E1000_COLLISION_DISTANCE
#define E1000_COLD_SHIFT                12

/* Number of Transmit and Receive Descriptors must be a multiple of 8 */
#define REQ_TX_DESCRIPTOR_MULTIPLE  8
#define REQ_RX_DESCRIPTOR_MULTIPLE  8

/* Default values for the transmit IPG register */
#define DEFAULT_82542_TIPG_IPGT        10
#define DEFAULT_82543_TIPG_IPGT_FIBER  9
#define DEFAULT_82543_TIPG_IPGT_COPPER 8

#define E1000_TIPG_IPGT_MASK  0x000003FF
#define E1000_TIPG_IPGR1_MASK 0x000FFC00
#define E1000_TIPG_IPGR2_MASK 0x3FF00000

#define DEFAULT_82542_TIPG_IPGR1 2
#define DEFAULT_82543_TIPG_IPGR1 8
#define E1000_TIPG_IPGR1_SHIFT  10

#define DEFAULT_82542_TIPG_IPGR2 10
#define DEFAULT_82543_TIPG_IPGR2 6
#define E1000_TIPG_IPGR2_SHIFT  20

#define E1000_TXDMAC_DPP 0x00000001

/* Adaptive IFS defines */
#define TX_THRESHOLD_START     8
#define TX_THRESHOLD_INCREMENT 10
#define TX_THRESHOLD_DECREMENT 1
#define TX_THRESHOLD_STOP      190
#define TX_THRESHOLD_DISABLE   0
#define TX_THRESHOLD_TIMER_MS  10000
#define MIN_NUM_XMITS          1000
#define IFS_MAX                80
#define IFS_STEP               10
#define IFS_MIN                40
#define IFS_RATIO              4

/* PBA constants */
#define E1000_PBA_16K 0x0010    /* 16KB, default TX allocation */
#define E1000_PBA_22K 0x0016
#define E1000_PBA_24K 0x0018
#define E1000_PBA_30K 0x001E
#define E1000_PBA_40K 0x0028
#define E1000_PBA_48K 0x0030    /* 48KB, default RX allocation */

/* Flow Control Constants */
#define FLOW_CONTROL_ADDRESS_LOW  0x00C28001
#define FLOW_CONTROL_ADDRESS_HIGH 0x00000100
#define FLOW_CONTROL_TYPE         0x8808

/* The historical defaults for the flow control values are given below. */
#define FC_DEFAULT_HI_THRESH        (0x8000)    /* 32KB */
#define FC_DEFAULT_LO_THRESH        (0x4000)    /* 16KB */
#define FC_DEFAULT_TX_TIMER         (0x100)     /* ~130 us */

/* PCIX Config space */
#define PCIX_COMMAND_REGISTER    0xE6
#define PCIX_STATUS_REGISTER_LO  0xE8
#define PCIX_STATUS_REGISTER_HI  0xEA

#define PCIX_COMMAND_MMRBC_MASK      0x000C
#define PCIX_COMMAND_MMRBC_SHIFT     0x2
#define PCIX_STATUS_HI_MMRBC_MASK    0x0060
#define PCIX_STATUS_HI_MMRBC_SHIFT   0x5
#define PCIX_STATUS_HI_MMRBC_4K      0x3
#define PCIX_STATUS_HI_MMRBC_2K      0x2


/* Number of bits required to shift right the "pause" bits from the
 * EEPROM (bits 13:12) to the "pause" (bits 8:7) field in the TXCW register.
 */
#define PAUSE_SHIFT 5

/* Number of bits required to shift left the "SWDPIO" bits from the
 * EEPROM (bits 8:5) to the "SWDPIO" (bits 25:22) field in the CTRL register.
 */
#define SWDPIO_SHIFT 17

/* Number of bits required to shift left the "SWDPIO_EXT" bits from the
 * EEPROM word F (bits 7:4) to the bits 11:8 of The Extended CTRL register.
 */
#define SWDPIO__EXT_SHIFT 4

/* Number of bits required to shift left the "ILOS" bit from the EEPROM
 * (bit 4) to the "ILOS" (bit 7) field in the CTRL register.
 */
#define ILOS_SHIFT  3


#define RECEIVE_BUFFER_ALIGN_SIZE  (256)

/* Number of milliseconds we wait for auto-negotiation to complete */
#define LINK_UP_TIMEOUT             500

#define E1000_TX_BUFFER_SIZE ((uint32_t)1514)

/* The carrier extension symbol, as rece