fet140_uart11_0115k_2.s43

TI低功耗MCU用例子

#include  "msp430x14x.h"
;******************************************************************************
;   MSP-FET430P140 Demo - USART1 UART 115200 Echo ISR, XT2 HF XTAL SMCLK 
;
;   Description; This program will echo a received character, RX interrupt 
;   service used. XT2 oscillator used in this example.
;   ACLK = MCLK = SMCLK = UCLK1 = XT2 = 8MHz
;   Baud rate divider with 8Mhz XTAL @115200 = 8MHz/115200 = 69.44(0045 2Ch)
;   //*An external 8MHz XTAL on X2IN X2OUT is required for ACLK*//	  
;
;                MSP430F149
;             -----------------
;         /|\|             X2IN|-  
;          | |                 | 8Mhz  
;          --|RST         X2OUT|-
;            |                 |
;            |             P3.6|------------>
;            |                 | 115200 - 8N1 
;            |             P3.7|<------------
;
;   M.Buccini
;   Texas Instruments, Inc
;   January 2002
;******************************************************************************
;------------------------------------------------------------------------------ 
            ORG     01100h                  ; Progam Start 
;------------------------------------------------------------------------------ 
RESET       mov.w   #0A00h,SP               ; Initialize 'F149 stackpointer
            call    #Init_Sys               ;
                                            ;   
Mainloop    jmp     Mainloop                ; Do nothing
                                            ;
;------------------------------------------------------------------------------ 
Init_Sys;   Initalize MSP430 system
;------------------------------------------------------------------------------ 
StopWDT     mov.w   #WDTPW+WDTHOLD,&WDTCTL  ; Stop WDT
SetupBC     bic.b   #XT2OFF,&BCSCTL1        ; XT2on
SetupOsc    bic.b   #OFIFG,&IFG1            ; Clear OSC fault flag 
            mov.w   #0FFh,R15               ; R15 = Delay 
SetupOsc1   dec.w   R15                     ; Additional delay to ensure start 
            jnz     SetupOsc1               ;
            bit.b   #OFIFG,&IFG1            ; OSC fault flag set? 
            jnz     SetupOsc                ; OSC Fault, clear flag again 
            bis.b   #SELM1+SELS,BCSCTL2     ; MCLK = SMCLK = XT2
                                            ;
SetupUART1  mov.b   #CHAR,&UCTL1            ; 8-bit characters
            mov.b   #SSEL1,&UTCTL1          ; UCLK = SMCLK
            mov.b   #045h,&UBR01            ; 8Mhz/115200 - 69.44
            mov.b   #000h,&UBR11            ; 
            mov.b   #02ch,&UMCTL1           ; Modulation
            bis.b   #UTXE1+URXE1,&ME2       ; Enable USART1 TXD/RXD
            bis.b   #URXIE1,&IE2            ; Enable USART1 RX interrupt
SetupP3     bis.b   #0C0h,&P3SEL            ; P3.6,7 = USART1 option select
            bis.b   #040h,&P3DIR            ; P3.6 = output direction 
            eint                            ; General enable interrupts
            ret                             ;
                                            ;
;------------------------------------------------------------------------------ 
USART1_ISR;  Echo back RXed character, confirm TX buffer is ready first
;------------------------------------------------------------------------------ 
TX2         bit.b   #UTXIFG1,&IFG2          ; USART1 TX buffer ready?
            jz      TX2                     ; Jump is TX buffer not ready
            mov.b   &RXBUF1,&TXBUF1         ; TX -> RXed character
            reti                            ; 
                                            ;
;------------------------------------------------------------------------------ 
;           Interrupt Vectors Used MSP430x13x/14x        
;------------------------------------------------------------------------------ 
            ORG     0FFFEh                  ; 
            DW      RESET                   ; POR, ext. Reset, Watchdog
            ORG     0FFE6h                  ; 
            DW      USART1_ISR              ; USART1 Receive
            end