cdu31a.h

LINUX 1.0 内核c源代码

/*
 * Definitions for a Sony interface CDROM drive.
 *
 * Corey Minyard ([e-mail])
 *
 *  Copyright (C) 1993  Corey Minyard
 *
 *  This program is free software; you can redistribute it and/or modify
 *  it under the terms of the GNU General Public License as published by
 *  the Free Software Foundation; either version 2 of the License, or
 *  (at your option) any later version.
 *
 *  This program is distributed in the hope that it will be useful,
 *  but WITHOUT ANY WARRANTY; without even the implied warranty of
 *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 *  GNU General Public License for more details.
 *
 *  You should have received a copy of the GNU General Public License
 *  along with this program; if not, write to the Free Software
 *  Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
 *
 */

/*
 * Offsets (from the base address) and bits for the various write registers
 * of the drive.
 */
#define SONY_CMD_REG_OFFSET	0
#define SONY_PARAM_REG_OFFSET	1
#define SONY_WRITE_REG_OFFSET	2
#define SONY_CONTROL_REG_OFFSET	3
#	define SONY_ATTN_CLR_BIT	0x01
#	define SONY_RES_RDY_CLR_BIT	0x02
#	define SONY_DATA_RDY_CLR_BIT	0x04
#	define SONY_ATTN_INT_EN_BIT	0x08
#	define SONY_RES_RDY_INT_EN_BIT	0x10
#	define SONY_DATA_RDY_INT_EN_BIT	0x20
#	define SONY_PARAM_CLR_BIT	0x40
#	define SONY_DRIVE_RESET_BIT	0x80

/*
 * Offsets (from the base address) and bits for the various read registers
 * of the drive.
 */
#define SONY_STATUS_REG_OFFSET	0
#	define SONY_ATTN_BIT		0x01
#	define SONY_RES_RDY_BIT		0x02
#	define SONY_DATA_RDY_BIT	0x04
#	define SONY_ATTN_INT_ST_BIT	0x08
#	define SONY_RES_RDY_INT_ST_BIT	0x10
#	define SONY_DATA_RDY_INT_ST_BIT	0x20
#	define SONY_DATA_REQUEST_BIT	0x40
#	define SONY_BUSY_BIT		0x80
#define SONY_RESULT_REG_OFFSET	1
#define SONY_READ_REG_OFFSET	2
#define SONY_FIFOST_REG_OFFSET	3
#	define SONY_PARAM_WRITE_RDY_BIT	0x01
#	define SONY_PARAM_REG_EMPTY_BIT	0x02
#	define SONY_RES_REG_NOT_EMP_BIT	0x04
#	define SONY_RES_REG_FULL_BIT	0x08

#define LOG_START_OFFSET	150	/* Offset of first logical sector */

#define SONY_DETECT_TIMEOUT	80	/* Maximum amount of time
					   that drive detection code
					   will wait for response
					   from drive (in 1/100th's
					   of seconds). */
 
#define SONY_JIFFIES_TIMEOUT	500	/* Maximum number of times the
					   drive will wait/try for an
					   operation */
#define SONY_RESET_TIMEOUT	100	/* Maximum number of times the
					   drive will wait/try a reset
					   operation */
#define SONY_READY_RETRIES	20000	/* How many times to retry a
					   spin waiting for a register
					   to come ready */

#define MAX_CDU31A_RETRIES	3	/* How many times to retry an
					   operation */

/* Commands to request or set drive control parameters and disc information */
#define SONY_REQ_DRIVE_CONFIG_CMD	0x00    /* Returns s_sony_drive_config */
#define SONY_REQ_DRIVE_MODE_CMD		0x01
#define SONY_REQ_DRIVE_PARAM_CMD	0x02
#define SONY_REQ_MECH_STATUS_CMD	0x03
#define SONY_REQ_AUDIO_STATUS_CMD	0x04
#define SONY_SET_DRIVE_PARAM_CMD	0x10
#define SONY_REQ_TOC_DATA_CMD		0x20    /* Returns s_sony_toc */
#define SONY_REQ_SUBCODE_ADDRESS_CMD	0x21    /* Returns s_sony_subcode */
#define SONY_REQ_UPC_EAN_CMD		0x22
#define SONY_REQ_ISRC_CMD		0x23
#define SONY_REQ_TOC_DATA_SPEC_CMD	0x24

/* Commands to request information from the drive */
#define SONY_READ_TOC_CMD		0x30
#define SONY_SEEK_CMD			0x31
#define SONY_READ_CMD			0x32
#define SONY_READ_BLKERR_STAT_CMD	0x34
#define SONY_ABORT_CMD			0x35
#define SONY_READ_TOC_SPEC_CMD		0x36

/* Commands to control audio */
#define SONY_AUDIO_PLAYBACK_CMD		0x40
#define SONY_AUDIO_STOP_CMD		0x41
#define SONY_AUDIO_SCAN_CMD		0x42

/* Miscellaneous control commands */
#define SONY_EJECT_CMD			0x50
#define SONY_SPIN_UP_CMD		0x51
#define SONY_SPIN_DOWN_CMD		0x52

/* Diagnostic commands */
#define SONY_WRITE_BUFFER_CMD		0x60
#define SONY_READ_BUFFER_CMD		0x61
#define SONY_DIAGNOSTICS_CMD		0x62


/*
 * The following are command paramters for the set drive parameter command
 */
#define SONY_SD_DECODE_PARAM		0x00
#define SONY_SD_INTERFACE_PARAM		0x01
#define SONY_SD_BUFFERING_PARAM		0x02
#define SONY_SD_AUDIO_PARAM		0x03
#define SONY_SD_AUDIO_VOLUME		0x04
#define SONY_SD_MECH_CONTROL		0x05
#define SONY_SD_AUTO_SPIN_DOWN_TIME	0x06

/*
 * The following extract information from the drive configuration about
 * the drive itself.
 */
#define SONY_HWC_GET_LOAD_MECH(c)	(c.hw_config[0] & 0x03)
#define SONY_HWC_EJECT(c)		(c.hw_config[0] & 0x04)
#define SONY_HWC_LED_SUPPORT(c)		(c.hw_config[0] & 0x08)
#define SONY_HWC_GET_BUF_MEM_SIZE(c)	((c.hw_config[0] & 0xc0) >> 6)
#define SONY_HWC_AUDIO_PLAYBACK(c)	(c.hw_config[1] & 0x01)
#define SONY_HWC_ELECTRIC_VOLUME(c)	(c.hw_config[1] & 0x02)
#define SONY_HWC_ELECTRIC_VOLUME_CTL(c)	(c.hw_config[1] & 0x04)

#define SONY_HWC_CADDY_LOAD_MECH	0x00
#define SONY_HWC_TRAY_LOAD_MECH		0x01
#define SONY_HWC_POPUP_LOAD_MECH	0x02
#define SONY_HWC_UNKWN_LOAD_MECH	0x03

#define SONY_HWC_8KB_BUFFER		0x00
#define SONY_HWC_32KB_BUFFER		0x01
#define SONY_HWC_64KB_BUFFER		0x02
#define SONY_HWC_UNKWN_BUFFER		0x03

/*
 * This is the complete status returned from the drive configuration request
 * command.
 */
struct s_sony_drive_config
{
   unsigned char exec_status[2];
   char vendor_id[8];
   char product_id[16];
   char product_rev_level[8];
   unsigned char hw_config[2];
};

/* The following is returned from the request subcode address command */
struct s_sony_subcode
{
   unsigned char exec_status[2];
   unsigned char address	:4;
   unsigned char control	:4;
   unsigned char track_num;
   unsigned char index_num;
   unsigned char rel_msf[3];
   unsigned char reserved1;
   unsigned char abs_msf[3];
};

/*
 * The following is returned from the request TOC (Table Of Contents) command.
 * (last_track_num-first_track_num+1) values are valid in tracks.
 */
struct s_sony_toc
{
   unsigned char exec_status[2];
   unsigned char address0	:4;
   unsigned char control0	:4;
   unsigned char point0;
   unsigned char first_track_num;
   unsigned char disk_type;
   unsigned char dummy0;
   unsigned char address1	:4;
   unsigned char control1	:4;
   unsigned char point1;
   unsigned char last_track_num;
   unsigned char dummy1;
   unsigned char dummy2;
   unsigned char address2	:4;
   unsigned char control2	:4;
   unsigned char point2;
   unsigned char lead_out_start_msf[3];
   struct
   {
      unsigned char address	:4;
      unsigned char control	:4;
      unsigned char track;
      unsigned char track_start_msf[3];
   } tracks[100];

   unsigned int lead_out_start_lba;
};


/*
 * The following are errors returned from the drive.
 */

/* Command error group */
#define SONY_ILL_CMD_ERR		0x10
#define SONY_ILL_PARAM_ERR		0x11

/* Mechanism group */
#define SONY_NOT_LOAD_ERR		0x20
#define SONY_NO_DISK_ERR		0x21
#define SONY_NOT_SPIN_ERR		0x22
#define SONY_SPIN_ERR			0x23
#define SONY_SPINDLE_SERVO_ERR		0x25
#define SONY_FOCUS_SERVO_ERR		0x26
#define SONY_EJECT_MECH_ERR		0x29
#define SONY_AUDIO_PLAYING_ERR		0x2a
#define SONY_EMERGENCY_EJECT_ERR	0x2c

/* Seek error group */
#define SONY_FOCUS_ERR			0x30
#define SONY_FRAME_SYNC_ERR		0x31
#define SONY_SUBCODE_ADDR_ERR		0x32
#define SONY_BLOCK_SYNC_ERR		0x33
#define SONY_HEADER_ADDR_ERR		0x34

/* Read error group */
#define SONY_ILL_TRACK_R_ERR		0x40
#define SONY_MODE_0_R_ERR		0x41
#define SONY_ILL_MODE_R_ERR		0x42
#define SONY_ILL_BLOCK_SIZE_R_ERR	0x43
#define SONY_MODE_R_ERR			0x44
#define SONY_FORM_R_ERR			0x45
#define SONY_LEAD_OUT_R_ERR		0x46
#define SONY_BUFFER_OVERRUN_R_ERR	0x47

/* Data error group */
#define SONY_UNREC_CIRC_ERR		0x53
#define SONY_UNREC_LECC_ERR		0x57

/* Subcode error group */
#define SONY_NO_TOC_ERR			0x60
#define SONY_SUBCODE_DATA_NVAL_ERR	0x61
#define SONY_FOCUS_ON_TOC_READ_ERR	0x63
#define SONY_FRAME_SYNC_ON_TOC_READ_ERR	0x64
#define SONY_TOC_DATA_ERR		0x65

/* Hardware failure group */
#define SONY_HW_FAILURE_ERR		0x70
#define SONY_LEAD_IN_A_ERR		0x91
#define SONY_LEAD_OUT_A_ERR		0x92
#define SONY_DATA_TRACK_A_ERR		0x93

/*
 * The following are returned from the Read With Block Error Status command.
 * They are not errors but information (Errors from the 0x5x group above may
 * also be returned
 */
#define SONY_NO_CIRC_ERR_BLK_STAT	0x50
#define SONY_NO_LECC_ERR_BLK_STAT	0x54
#define SONY_RECOV_LECC_ERR_BLK_STAT	0x55
#define SONY_NO_ERR_DETECTION_STAT	0x59

/* 
 * The following is not an error returned by the drive, but by the code
 * that talks to the drive.  It is returned because of a timeout.
 */
#define SONY_TIMEOUT_OP_ERR		0x01
#define SONY_SIGNAL_OP_ERR		0x02


/*
 * The following are attention code for asyncronous events from the drive.
 */

/* Standard attention group */
#define SONY_EMER_EJECT_ATTN		0x2c
#define SONY_HW_FAILURE_ATTN		0x70
#define SONY_MECH_LOADED_ATTN		0x80
#define SONY_EJECT_PUSHED_ATTN		0x81

/* Audio attention group */
#define SONY_AUDIO_PLAY_DONE_ATTN	0x90
#define SONY_LEAD_IN_ERR_ATTN	 	0x91
#define SONY_LEAD_OUT_ERR_ATTN	 	0x92
#define SONY_DATA_TRACK_ERR_ATTN	0x93
#define SONY_AUDIO_PLAYBACK_ERR_ATTN	0x94

/* Auto spin up group */
#define SONY_SPIN_UP_COMPLETE_ATTN	0x24
#define SONY_SPINDLE_SERVO_ERR_ATTN	0x25
#define SONY_FOCUS_SERVO_ERR_ATTN	0x26
#define SONY_TOC_READ_DONE_ATTN		0x62
#define SONY_FOCUS_ON_TOC_READ_ERR_ATTN	0x63
#define SONY_SYNC_ON_TOC_READ_ERR_ATTN	0x65

/* Auto eject group */
#define SONY_SPIN_DOWN_COMPLETE_ATTN	0x27
#define SONY_EJECT_COMPLETE_ATTN	0x28
#define SONY_EJECT_MECH_ERR_ATTN	0x29