pc_serial.h

eCos1.31版

#ifndef CYGONCE_I386_PC_SERIAL_H
#define CYGONCE_I386_PC_SERIAL_H

// ====================================================================
//
//      pc_serial.h
//
//      Device I/O - Description of i386/PC 8250/16550 serial hardware
//
// ====================================================================
//####COPYRIGHTBEGIN####
//                                                                          
// -------------------------------------------                              
// The contents of this file are subject to the Red Hat eCos Public License 
// Version 1.0 (the "License"); you may not use this file except in         
// compliance with the License.  You may obtain a copy of the License at    
// http://sourceware.cygnus.com/ecos                                        
//                                                                          
// Software distributed under the License is distributed on an       
// basis, WITHOUT WARRANTY OF ANY KIND, either express or implied.  See the 
// License for the specific language governing rights and limitations under 
// the License.                                                             
//                                                                          
// The Original Code is eCos - Embedded Configurable Operating System,      
// released September 30, 1998.                                             
//                                                                          
// The Initial Developer of the Original Code is Red Hat.                   
// Portions created by Red Hat are                                          
// Copyright (C) 1998, 1999, 2000 Red Hat, Inc.                             
// All Rights Reserved.                                                     
// -------------------------------------------                              
//                                                                          
//####COPYRIGHTEND####
// ====================================================================
//#####DESCRIPTIONBEGIN####
//
// Author(s):           gthomas
// Contributors:        gthomas, pjo
// Date:        1999-02-04
// Purpose:     Internal interfaces for serial I/O drivers
// Description:
//
//####DESCRIPTIONEND####
//
// ====================================================================

// Description of serial ports on i386/PC 8250/16550


// Receive control registers
#define RHR			0    // Receive holding register
#define ISR			2    // Interrupt status register
#define LSR			5    // Line status register
#define MSR			6    // Modem status register
#define SCR			7    // Scratch register

// Transmit control registers
#define THR			0    // Transmit holding register
#define IER			1    // Interrupt enable register
#define FCR			2    // FIFO control register
#define LCR			3    // Line control register
#define MCR			4    // Modem control register
#define LDL			0    // LSB of baud rate
#define MDL			1    // MSB of baud rate

// Interrupt Enable Register
#define IER_RCV 0x01
#define IER_XMT 0x02
#define IER_LS  0x04
#define IER_MS  0x08

// Line Control Register
#define LCR_WL5 0x00    // Word length
#define LCR_WL6 0x01
#define LCR_WL7 0x02
#define LCR_WL8 0x03
#define LCR_SB1 0x00    // Number of stop bits
#define LCR_SB1_5 0x04  // 1.5 -> only valid with 5 bit words
#define LCR_SB2 0x04
#define LCR_PN  0x00    // Parity mode - none
#define LCR_PE  0x0C    // Parity mode - even
#define LCR_PO  0x08    // Parity mode - odd
#define LCR_PM  0x28    // Forced "mark" parity
#define LCR_PS  0x38    // Forced "space" parity
#define LCR_DL  0x80    // Enable baud rate latch

// Line Status Register
#define LSR_RSR 0x01
#define LSR_THE 0x20

// Modem Control Register
#define MCR_DTR 0x01
#define MCR_RTS 0x02
#define MCR_INT 0x0C   // Enable interrupts
#define MCR_LOOP 0x10  // Loopback mode.


// FIFO control register
#define FCR_FE	0x01	// Fifo enable
#define FCR_RFR	0x02	// Receiver fifo reset
#define FCR_TFR	0x04	// Transmitter fifo reset
#define FCR_RT14 0xC0
#define FCR_RT8	0x80
#define FCR_RT4	0x40
#define FCR_RT1	0x00

// FIFO lengths
#define PC16550_FIFO_TX_LENGTH	(16 /*only for s16550a*/)
#define PC16550_FIFO_RX_LENGTH	(16 /*only for s16550a*/)

// Interrupt status register
#define ISR_Tx  0x02
#define ISR_Rx  0x04

static unsigned char select_word_length[] = {
    LCR_WL5,    // 5 bits / word (char)
    LCR_WL6,
    LCR_WL7,
    LCR_WL8
};

static unsigned char select_stop_bits[] = {
    0,
    LCR_SB1,    // 1 stop bit
    LCR_SB1_5,  // 1.5 stop bit
    LCR_SB2     // 2 stop bits
};

static unsigned char select_parity[] = {
    LCR_PN,     // No parity
    LCR_PE,     // Even parity
    LCR_PO,     // Odd parity
    LCR_PM,     // Mark parity
    LCR_PS,     // Space parity
};

// Baud rate values, based on raw 24MHz clock

static unsigned short select_baud[] = {
           0,  // Unused
        2304,  // 50
        1536,  // 75
        1047,  // 110
         857,  // 134.5
         768,  // 150
         576,  // 200
         384,  // 300
         192,  // 600
          96,  // 1200
          64,  // 1800
          48,  // 2400
          32,  // 3600
          24,  // 4800
          16,  // 7200
          12,  // 9600
           8,  // 14400
           6,  // 19200
           3,  // 38400
           2,  // 57600
           1,  // 115200
           0,  // 230400
};

#endif // CYGONCE_I386_PC_SERIAL_H