cogent_serial.h

eCos1.31版

//==========================================================================
//
//      io/serial/powerpc/cogent_serial.h
//
//      PowerPC Cogent Serial I/O definitions.
//
//==========================================================================
//####COPYRIGHTBEGIN####
//                                                                          
// -------------------------------------------                              
// The contents of this file are subject to the Red Hat eCos Public License 
// Version 1.1 (the "License"); you may not use this file except in         
// compliance with the License.  You may obtain a copy of the License at    
// http://www.redhat.com/                                                   
//                                                                          
// Software distributed under the License is distributed on an "AS IS"      
// basis, WITHOUT WARRANTY OF ANY KIND, either express or implied.  See the 
// License for the specific language governing rights and limitations under 
// the License.                                                             
//                                                                          
// The Original Code is eCos - Embedded Configurable Operating System,      
// released September 30, 1998.                                             
//                                                                          
// The Initial Developer of the Original Code is Red Hat.                   
// Portions created by Red Hat are                                          
// Copyright (C) 1998, 1999, 2000 Red Hat, Inc.                             
// All Rights Reserved.                                                     
// -------------------------------------------                              
//                                                                          
//####COPYRIGHTEND####
//==========================================================================
//#####DESCRIPTIONBEGIN####
//
// Author(s):   jskov, based on ARM driver by gthomas
// Contributors:gthomas, jskov
// Date:        1999-03-02
// Purpose:     Cogent Serial definitions
//####DESCRIPTIONEND####
//==========================================================================

// Description of serial ports on Cogent board

// Interrupt Enable Register
#define IER_RCV 0x01
#define IER_XMT 0x02
#define IER_LS  0x04
#define IER_MS  0x08

// Line Control Register
#define LCR_WL5 0x00    // Word length
#define LCR_WL6 0x01
#define LCR_WL7 0x02
#define LCR_WL8 0x03
#define LCR_SB1 0x00    // Number of stop bits
#define LCR_SB1_5 0x04  // 1.5 -> only valid with 5 bit words
#define LCR_SB2 0x04
#define LCR_PN  0x00    // Parity mode - none
#define LCR_PE  0x0C    // Parity mode - even
#define LCR_PO  0x08    // Parity mode - odd
#define LCR_PM  0x28    // Forced "mark" parity
#define LCR_PS  0x38    // Forced "space" parity
#define LCR_DL  0x80    // Enable baud rate latch

// Line Status Register
#define LSR_RSR 0x01
#define LSR_THE 0x20

// Modem Control Register
#define MCR_DTR 0x01
#define MCR_RTS 0x02
#define MCR_INT 0x08   // Enable interrupts

// Interrupt status register
#define ISR_Tx  0x02
#define ISR_Rx  0x04

// FIFO control register
#define FCR_ENABLE     0x01
#define FCR_CLEAR_RCVR 0x02
#define FCR_CLEAR_XMIT 0x04


////////////////////////////////////////////////////////////
// Clean this up.

//-----------------------------------------------------------------------------
// There are two serial ports.
#define CMA_SER_16550_BASE_A    0xe900047 // port A
#define CMA_SER_16550_BASE_B    0xe900007 // port B
#define SER_16550_BASE CMA_SER_16550_BASE_B

//-----------------------------------------------------------------------------
// Define the serial registers. The Cogent board is equipped with a 16552
// serial chip.
#define SER_16550_RBR 0x00   // receiver buffer register, read, dlab = 0
#define SER_16550_THR 0x00   // transmitter holding register, write, dlab = 0
#define SER_16550_DLL 0x00   // divisor latch (LS), read/write, dlab = 1
#define SER_16550_IER 0x08   // interrupt enable register, read/write, dlab = 0
#define SER_16550_DLM 0x08   // divisor latch (MS), read/write, dlab = 1
#define SER_16550_IIR 0x10   // interrupt identification reg, read, dlab = 0
#define SER_16550_FCR 0x10   // fifo control register, write, dlab = 0
#define SER_16550_AFR 0x10   // alternate function reg, read/write, dlab = 1
#define SER_16550_LCR 0x18   // line control register, read/write
#define SER_16550_MCR 0x20   // modem control register, read/write
#define SER_16550_LSR 0x28   // line status register, read
#define SER_16550_MSR 0x30   // modem status register, read
#define SER_16550_SCR 0x38   // scratch pad register

// The interrupt enable register bits.
#define SIO_IER_ERDAI   0x01            // enable received data available irq
#define SIO_IER_ETHREI  0x02            // enable THR empty interrupt
#define SIO_IER_ELSI    0x04            // enable receiver line status irq
#define SIO_IER_EMSI    0x08            // enable modem status interrupt

// The interrupt identification register bits.
#define SIO_IIR_IP      0x01            // 0 if interrupt pending
#define SIO_IIR_ID_MASK 0x0e            // mask for interrupt ID bits

// The line status register bits.
#define SIO_LSR_DR      0x01            // data ready
#define SIO_LSR_OE      0x02            // overrun error
#define SIO_LSR_PE      0x04            // parity error
#define SIO_LSR_FE      0x08            // framing error
#define SIO_LSR_BI      0x10            // break interrupt
#define SIO_LSR_THRE    0x20            // transmitter holding register empty
#define SIO_LSR_TEMT    0x40            // transmitter register empty
#define SIO_LSR_ERR     0x80            // any error condition

// The modem status register bits.
#define SIO_MSR_DCTS  0x01              // delta clear to send
#define SIO_MSR_DDSR  0x02              // delta data set ready
#define SIO_MSR_TERI  0x04              // trailing edge ring indicator
#define SIO_MSR_DDCD  0x08              // delta data carrier detect
#define SIO_MSR_CTS   0x10              // clear to send
#define SIO_MSR_DSR   0x20              // data set ready
#define SIO_MSR_RI    0x40              // ring indicator
#define SIO_MSR_DCD   0x80              // data carrier detect

// The line control register bits.
#define SIO_LCR_WLS0   0x01             // word length select bit 0
#define SIO_LCR_WLS1   0x02             // word length select bit 1
#define SIO_LCR_STB    0x04             // number of stop bits
#define SIO_LCR_PEN    0x08             // parity enable
#define SIO_LCR_EPS    0x10             // even parity select
#define SIO_LCR_SP     0x20             // stick parity
#define SIO_LCR_SB     0x40             // set break
#define SIO_LCR_DLAB   0x80             // divisor latch access bit

// The FIFO control register
#define SIO_FCR_FCR0   0x01             // enable xmit and rcvr fifos
#define SIO_FCR_FCR1   0x02             // clear RCVR FIFO
#define SIO_FCR_FCR2   0x04             // clear XMIT FIFO
/////////////////////////////////////////


static unsigned char select_word_length[] = {
    LCR_WL5,    // 5 bits / word (char)
    LCR_WL6,
    LCR_WL7,
    LCR_WL8
};

static unsigned char select_stop_bits[] = {
    0,
    LCR_SB1,    // 1 stop bit
    LCR_SB1_5,  // 1.5 stop bit
    LCR_SB2     // 2 stop bits
};

static unsigned char select_parity[] = {
    LCR_PN,     // No parity
    LCR_PE,     // Even parity
    LCR_PO,     // Odd parity
    LCR_PM,     // Mark parity
    LCR_PS,     // Space parity
};

// FIXME: calc all properly
// The Cogent board has a 3.6864 MHz crystal
static unsigned short select_baud[] = {
    0,    // Unused
    4608, // 50
    0,    // 75
    2094, // 110
    0,    // 134.5
    1536, // 150
    0,    // 200
    768,  // 300
    384,  // 600
    182,  // 1200
    0,    // 1800
    96,   // 2400
    0,    // 3600
    48,   // 4800
    32,   // 7200
    24,   // 9600
    16,   // 14400
    12,   // 19200
    6,    // 38400
    4,    // 57600
    2,    // 115200
    0,    // 230400
};