📄 00000007.htm
字号:
<HTML><HEAD> <TITLE>BBS水木清华站∶精华区</TITLE></HEAD><BODY><CENTER><H1>BBS水木清华站∶精华区</H1></CENTER>发信人: scaner (好好), 信区: Linux <BR>标 题: LILO启动失败原因的判断方法 <BR>发信站: BBS 水木清华站 (Mon Aug 3 17:17:19 1998) <BR> <BR> <BR>浏览了一下lilo的Readme,看见如下一段: <BR> <BR>When LILO loads itself, it displays the word "LILO". Each letter is printed <BR>before or after performing some specific action. If LILO fails at some <BR>point, the letters printed so far can be used to identify the problem. This <BR>is described in more detail in the technical overview. <BR> <BR>想到常常有人问为什么Lilo启动时到了LI就 <BR>死机,是应为Linux 在启动时还要再装入一 <BR>个较大的启动模块,就是一般的/boot/boot.b <BR>如果无法正常装入,就只出LI两个字母了。 <BR> <BR>下面是原文: <BR>When LILO loads itself, it displays the word "LILO". Each letter is printed <BR>before or after performing some specific action. If LILO fails at some <BR>point, the letters printed so far can be used to identify the problem. This <BR>is described in more detail in the technical overview. <BR> <BR>Note that some hex digits may be inserted after the first "L" if a <BR>transient disk problem occurs. Unless LILO stops at that point, generating <BR>an endless stream of error codes, such hex digits do not indicate a severe <BR>problem. <BR> <BR> (<nothing>) No part of LILO has been loaded. LILO either isn't installed <BR> or the partition on which its boot sector is located isn't active. <BR> L <error> ... The first stage boot loader has been loaded and started, <BR> but it can't load the second stage boot loader. The two-digit error <BR> codes indicate the type of problem. (See also section "Disk error <BR> codes".) This condition usually indicates a media failure or a geometry <BR> mismatch (e.g. bad disk parameters, see section "Disk geometry"). <BR> LI The first stage boot loader was able to load the second stage boot <BR> loader, but has failed to execute it. This can either be caused by a <BR> geometry mismatch or by moving /boot/boot.b without running the map <BR> installer. <BR> LIL The second stage boot loader has been started, but it can't load <BR> the descriptor table from the map file. This is typically caused by a <BR> media failure or by a geometry mismatch. <BR> LIL? The second stage boot loader has been loaded at an incorrect <BR> address. This is typically caused by a subtle geometry mismatch or by <BR> moving /boot/boot.b without running the map installer. <BR> LIL- The descriptor table is corrupt. This can either be caused by a <BR> geometry mismatch or by moving /boot/map without running the map <BR> installer. <BR> LILO All parts of LILO have been successfully loaded. <BR> <BR> <BR> <BR> <BR>-- <BR>#telnet I.want.to.go <BR>telnet: Unable to connect to remote host: No Route to host <BR> <BR>※ 来源:·BBS 水木清华站 bbs.net.tsinghua.edu.cn·[FROM: 202.119.79.71] <BR><CENTER><H1>BBS水木清华站∶精华区</H1></CENTER></BODY></HTML>
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -