📄 fun.c
字号:
#include "f2407_c.h"
#define PI 3.1415926
unsigned int pwm_half_per=3000; /*PWM modulate frequency*/
void sys_ini(void)
{
/*** Configure the System Control and Status registers ***/
*SCSR1 = 0x00FD;
/*
bit 15 0: reserved
bit 14 0: CLKOUT = CPUCLK
bit 13-12 00: IDLE1 selected for low-power mode
bit 11-9 000: PLL x4 mode
bit 8 0: reserved
bit 7 1: 1 = enable ADC module clock
bit 6 1: 1 = enable SCI module clock
bit 5 1: 1 = enable SPI module clock
bit 4 1: 1 = enable CAN module clock
bit 3 1: 1 = enable EVB module clock
bit 2 1: 1 = enable EVA module clock
bit 1 0: reserved
bit 0 1: clear the ILLADR bit
*/
*SCSR2 = (*SCSR2 | 0x000B) & 0x000F;
/*
bit 15-6 0's: reserved
bit 5 0: do NOT clear the WD OVERRIDE bit
bit 4 0: XMIF_HI-Z, 0=normal mode, 1=Hi-Z'd
bit 3 1: disable the boot ROM, enable the FLASH
bit 2 no change MP/MC* bit reflects state of MP/MC* pin
bit 1-0 11: 11 = SARAM mapped to prog and data
*/
/*** Disable the watchdog timer ***/
*WDCR = 0x00E8;
/*
bits 15-8 0's: reserved
bit 7 1: clear WD flag
bit 6 1: disable the dog
bit 5-3 101: must be written as 101
bit 2-0 000: WDCLK divider = 1
*/
/*** Setup external memory interface for LF2407 EVM ***/
WSGR = 0x0040;
/*
bit 15-11 0's: reserved
bit 10-9 00: bus visibility off
bit 8-6 001: 1 wait-state for I/O space
bit 5-3 000: 0 wait-state for data space
bit 2-0 000: 0 wait state for program space
*/
/*** Setup shared I/O pins ***/
*MCRA = 0x0fc0; /* group A pins */
/*
bit 15 0: 0=IOPB7, 1=TCLKINA
bit 14 0: 0=IOPB6, 1=TDIRA
bit 13 0: 0=IOPB5, 1=T2PWM/T2CMP
bit 12 0: 0=IOPB4, 1=T1PWM/T1CMP
bit 11 1: 0=IOPB3, 1=PWM6
bit 10 1: 0=IOPB2, 1=PWM5
bit 9 1: 0=IOPB1, 1=PWM4
bit 8 1: 0=IOPB0, 1=PWM3
bit 7 1: 0=IOPA7, 1=PWM2
bit 6 1: 0=IOPA6, 1=PWM1
bit 5 0: 0=IOPA5, 1=CAP3
bit 4 0: 0=IOPA4, 1=CAP2/QEP2
bit 3 0: 0=IOPA3, 1=CAP1/QEP1
bit 2 0: 0=IOPA2, 1=XINT1
bit 1 0: 0=IOPA1, 1=SCIRXD
bit 0 0: 0=IOPA0, 1=SCITXD
*/
*MCRB = 0xFE00; /* group B pins */
/*
bit 15 1: 0=reserved, 1=TMS2 (always write as 1)
bit 14 1: 0=reserved, 1=TMS (always write as 1)
bit 13 1: 0=reserved, 1=TD0 (always write as 1)
bit 12 1: 0=reserved, 1=TDI (always write as 1)
bit 11 1: 0=reserved, 1=TCK (always write as 1)
bit 10 1: 0=reserved, 1=EMU1 (always write as 1)
bit 9 1: 0=reserved, 1=EMU0 (always write as 1)
bit 8 0: 0=IOPD0, 1=XINT2/ADCSOC
bit 7 0: 0=IOPC7, 1=CANRX
bit 6 0: 0=IOPC6, 1=CANTX
bit 5 0: 0=IOPC5, 1=SPISTE
bit 4 0: 0=IOPC4, 1=SPICLK
bit 3 0: 0=IOPC3, 1=SPISOMI
bit 2 0: 0=IOPC2, 1=SPISIMO
bit 1 0: 0=IOPC1, 1=BIO*
bit 0 0: 0=IOPC0, 1=W/R*
*/
*MCRC = 0x0000; /* group C pins */
/*
bit 15 0: reserved
bit 14 0: 0=IOPF6, 1=IOPF6
bit 13 0: 0=IOPF5, 1=TCLKINB
bit 12 0: 0=IOPF4, 1=TDIRB
bit 11 0: 0=IOPF3, 1=T4PWM/T4CMP
bit 10 0: 0=IOPF2, 1=T3PWM/T3CMP
bit 9 0: 0=IOPF1, 1=CAP6
bit 8 0: 0=IOPF0, 1=CAP5/QEP4
bit 7 0: 0=IOPE7, 1=CAP4/QEP3
bit 6 0: 0=IOPE6, 1=PWM12
bit 5 0: 0=IOPE5, 1=PWM11
bit 4 0: 0=IOPE4, 1=PWM10
bit 3 0: 0=IOPE3, 1=PWM9
bit 2 0: 0=IOPE2, 1=PWM8
bit 1 0: 0=IOPE1, 1=PWM7
bit 0 0: 0=IOPE0, 1=CLKOUT
*/
*IMR = 0x0000; /* clear the IMR register */
*IFR = 0x003F; /* clear any pending core interrupts */
*EVAIMRA = 0x0000; /* enable desired EVA group A interrupts */
*EVAIMRB = 0x0000; /* enable desired EVA group B interrupts */
*EVAIMRC = 0x0000; /* enable desired EVA group C interrupts */
*EVAIFRA = 0xFFFF; /* clear all EVA group A interrupts */
*EVAIFRB = 0xFFFF; /* clear all EVA group B interrupts */
*EVAIFRC = 0xFFFF; /* clear all EVA group C interrupts */
*EVBIFRA = 0xFFFF; /* clear all EVB group A interrupts */
*EVBIFRB = 0xFFFF; /* clear all EVB group B interrupts */
*EVBIFRC = 0xFFFF; /* clear all EVB group C interrupts */
*EVBIMRA = 0x0000; /* enable desired EVB group A interrupts */
*EVBIMRB = 0x0000; /* enable desired EVB group B interrupts */
*EVBIMRC = 0x0000; /* enable desired EVB group C interrupts */
}
void pwm_init(void)
{
/*** Setup timers 1 and 2, and the PWM configuration ***/
*T1CON = 0x0000; /* disable timer 1 */
*T2CON = 0x0000; /* disable timer 2 */
*GPTCONA = 0x0000; /* configure GPTCONA */
/*
bit 15 0: reserved
bit 14 0: T2STAT, read-only
bit 13 0: T1STAT, read-only
bit 12-11 00: reserved
bit 10-9 00: T2TOADC, 00 = no timer2 event starts ADC
bit 8-7 00: T1TOADC, 00 = no timer1 event starts ADC
bit 6 0: TCOMPOE, 0 = Hi-z all timer compare outputs
bit 5-4 00: reserved
bit 3-2 00: T2PIN, 00 = forced low
bit 1-0 00: T1PIN, 00 = forced low
*/
/* Timer 1: configure to clock the PWM on PWM1 pin */
/* Symmetric PWM, 20KHz carrier frequency, 25% duty cycle */
*T1CNT = 0x0000; /* clear timer counter */
*T1PR = pwm_half_per; /* set timer period */
*DBTCONA = 0x0000; /* deadband units off */
*CMPR1 = pwm_half_per*0.25; /* set PWM1 duty cycle */
*ACTRA = 0x0666; /* PWM1 pin set active high */
/*
bit 15 0: space vector dir is CCW (don't care)
bit 14-12 000: basic space vector is 000 (dont' care)
bit 11-10 01: PWM6/IOPB3 pin active low
bit 9-8 10: PWM5/IOPB2 pin active high
bit 7-6 01: PWM4/IOPB1 pin active low
bit 5-4 10: PWM3/IOPB0 pin active high
bit 3-2 01: PWM2/IOPA7 pin active low
bit 1-0 10: PWM1/IOPA6 pin active high
*/
*COMCONA = 0x8200; /* configure COMCON register */
/*
bit 15 1: 1 = enable compare operation
bit 14-13 00: 00 = reload CMPRx regs on timer 1 underflow
bit 12 0: 0 = space vector disabled
bit 11-10 00: 00 = reload ACTR on timer 1 underflow
bit 9 1: 1 = enable PWM pins
bit 8-0 0's: reserved
*/
*T1CON = 0x0840; /* configure T1CON register */
/*
bit 15-14 00: stop immediately on emulator suspend
bit 13 0: reserved
bit 12-11 01: 01 = continous-up/down count mode
bit 10-8 000: 000 = x/1 prescaler
bit 7 0: reserved in T1CON
bit 6 1: TENABLE, 1 = enable timer
bit 5-4 00: 00 = CPUCLK is clock source
bit 3-2 00: 00 = reload compare reg on underflow
bit 1 0: 0 = disable timer compare
bit 0 0: reserved in T1CON
*/
*IMR |= 0x0002; /* enable desired core interrupts (in2)*/
/*** Setup the event manager interrupts ***/
*EVAIMRA |= 0x0200; /* enable desired EVA group A interrupts */
*EVAIMRB = 0x0000; /* enable desired EVA group B interrupts */
*EVAIMRC = 0x0000; /* enable desired EVA group C interrupts */
}
/********************** interrupt 2 service routine************************/
interrupt void inter2_isr(void)
{
*EVAIFRA = *EVAIFRA & 0x0200;
if(*PIVR==0x0029) /*time1 overbelow interrupt*/
{
*CMPR1= pwm_half_per*0.25;
*CMPR2= pwm_half_per*0.5;
*CMPR3= pwm_half_per*0.75;
}
asm(" CLRC INTM");
}
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -