📄 cs8900.h
字号:
//------------------------------------------------------------------------------
// Name: cs8900.h
// Func: header-file for cs8900.c
// Ver.: 1.1
// Date: January 2004
// Auth: Andreas Dannenberg
// MSP430 Applications
// Texas Instruments Inc.
// Rem.: -
//------------------------------------------------------------------------------
#ifndef __CS8900_H
#define __CS8900_H
#define MYMAC_1 0 // our ethernet (MAC) address
#define MYMAC_2 1 // (MUST be unique in LAN!)
#define MYMAC_3 2
#define MYMAC_4 3
#define MYMAC_5 4
#define MYMAC_6 5
#define IOR (0x40) // CS8900's ISA-bus interface pins
#define IOW (0x80)
// definitions for Crystal CS8900 ethernet-controller
// based on linux-header by Russel Nelson
#define PP_ChipID (0x0000) // offset 0h -> Corp-ID
// offset 2h -> Model/Product Number
// offset 3h -> Chip Revision Number
#define PP_ISAIOB (0x0020) // IO base address
#define PP_CS8900_ISAINT (0x0022) // ISA interrupt select
#define PP_CS8900_ISADMA (0x0024) // ISA Rec DMA channel
#define PP_ISASOF (0x0026) // ISA DMA offset
#define PP_DmaFrameCnt (0x0028) // ISA DMA Frame count
#define PP_DmaByteCnt (0x002a) // ISA DMA Byte count
#define PP_CS8900_ISAMemB (0x002c) // Memory base
#define PP_ISABootBase (0x0030) // Boot Prom base
#define PP_ISABootMask (0x0034) // Boot Prom Mask
// EEPROM data and command registers
#define PP_EECMD (0x0040) // NVR Interface Command register
#define PP_EEData (0x0042) // NVR Interface Data Register
// Configuration and control registers
#define PP_RxCFG (0x0102) // Rx Bus config
#define PP_RxCTL (0x0104) // Receive Control Register
#define PP_TxCFG (0x0106) // Transmit Config Register
#define PP_TxCMD (0x0108) // Transmit Command Register
#define PP_BufCFG (0x010a) // Bus configuration Register
#define PP_LineCTL (0x0112) // Line Config Register
#define PP_SelfCTL (0x0114) // Self Command Register
#define PP_BusCTL (0x0116) // ISA bus control Register
#define PP_TestCTL (0x0118) // Test Register
// Status and Event Registers
#define PP_ISQ (0x0120) // Interrupt Status
#define PP_RxEvent (0x0124) // Rx Event Register
#define PP_TxEvent (0x0128) // Tx Event Register
#define PP_BufEvent (0x012c) // Bus Event Register
#define PP_RxMiss (0x0130) // Receive Miss Count
#define PP_TxCol (0x0132) // Transmit Collision Count
#define PP_LineST (0x0134) // Line State Register
#define PP_SelfST (0x0136) // Self State register
#define PP_BusST (0x0138) // Bus Status
#define PP_TDR (0x013c) // Time Domain Reflectometry
// Initiate Transmit Registers
#define PP_TxCommand (0x0144) // Tx Command
#define PP_TxLength (0x0146) // Tx Length
// Adress Filter Registers
#define PP_LAF (0x0150) // Hash Table
#define PP_IA (0x0158) // Physical Address Register
// Frame Location
#define PP_RxStatus (0x0400) // Receive start of frame
#define PP_RxLength (0x0402) // Receive Length of frame
#define PP_RxFrame (0x0404) // Receive frame pointer
#define PP_TxFrame (0x0a00) // Transmit frame pointer
// Primary I/O Base Address. If no I/O base is supplied by the user, then this
// can be used as the default I/O base to access the PacketPage Area.
#define DEFAULTIOBASE (0x0300
// PP_RxCFG - Receive Configuration and Interrupt Mask bit definition - Read/write
#define SKIP_1 (0x0040)
#define RX_STREAM_ENBL (0x0080)
#define RX_OK_ENBL (0x0100)
#define RX_DMA_ONLY (0x0200)
#define AUTO_RX_DMA (0x0400)
#define BUFFER_CRC (0x0800)
#define RX_CRC_ERROR_ENBL (0x1000)
#define RX_RUNT_ENBL (0x2000)
#define RX_EXTRA_DATA_ENBL (0x4000)
// PP_RxCTL - Receive Control bit definition - Read/write
#define RX_IA_HASH_ACCEPT (0x0040)
#define RX_PROM_ACCEPT (0x0080)
#define RX_OK_ACCEPT (0x0100)
#define RX_MULTCAST_ACCEPT (0x0200)
#define RX_IA_ACCEPT (0x0400)
#define RX_BROADCAST_ACCEPT (0x0800)
#define RX_BAD_CRC_ACCEPT (0x1000)
#define RX_RUNT_ACCEPT (0x2000)
#define RX_EXTRA_DATA_ACCEPT (0x4000)
// PP_TxCFG - Transmit Configuration Interrupt Mask bit definition - Read/write
#define TX_LOST_CRS_ENBL (0x0040)
#define TX_SQE_ERROR_ENBL (0x0080)
#define TX_OK_ENBL (0x0100)
#define TX_LATE_COL_ENBL (0x0200)
#define TX_JBR_ENBL (0x0400)
#define TX_ANY_COL_ENBL (0x0800)
#define TX_16_COL_ENBL (0x8000)
// PP_TxCMD - Transmit Command bit definition - Read-only and
// PP_TxCommand - Write-only
#define TX_START_5_BYTES (0x0000)
#define TX_START_381_BYTES (0x0040)
#define TX_START_1021_BYTES (0x0080)
#define TX_START_ALL_BYTES (0x00C0)
#define TX_FORCE (0x0100)
#define TX_ONE_COL (0x0200)
#define TX_NO_CRC (0x1000)
#define TX_RUNT (0x2000)
// PP_BufCFG - Buffer Configuration Interrupt Mask bit definition - Read/write
#define GENERATE_SW_INTERRUPT (0x0040)
#define RX_DMA_ENBL (0x0080)
#define READY_FOR_TX_ENBL (0x0100)
#define TX_UNDERRUN_ENBL (0x0200)
#define RX_MISS_ENBL (0x0400)
#define RX_128_BYTE_ENBL (0x0800)
#define TX_COL_COUNT_OVRFLOW_ENBL (0x1000)
#define RX_MISS_COUNT_OVRFLOW_ENBL (0x2000)
#define RX_DEST_MATCH_ENBL (0x8000)
// PP_LineCTL - Line Control bit definition - Read/write
#define SERIAL_RX_ON (0x0040)
#define SERIAL_TX_ON (0x0080)
#define AUI_ONLY (0x0100)
#define AUTO_AUI_10BASET (0x0200)
#define MODIFIED_BACKOFF (0x0800)
#define NO_AUTO_POLARITY (0x1000)
#define TWO_PART_DEFDIS (0x2000)
#define LOW_RX_SQUELCH (0x4000)
// PP_SelfCTL - Software Self Control bit definition - Read/write
#define POWER_ON_RESET (0x0040)
#define SW_STOP (0x0100)
#define SLEEP_ON (0x0200)
#define AUTO_WAKEUP (0x0400)
#define HCB0_ENBL (0x1000)
#define HCB1_ENBL (0x2000)
#define HCB0 (0x4000)
#define HCB1 (0x8000)
// PP_BusCTL - ISA Bus Control bit definition - Read/write
#define RESET_RX_DMA (0x0040)
#define MEMORY_ON (0x0400)
#define DMA_BURST_MODE (0x0800)
#define IO_CHANNEL_READY_ON (0x1000)
#define RX_DMA_SIZE_64K (0x2000)
#define ENABLE_IRQ (0x8000)
// PP_TestCTL - Test Control bit definition - Read/write
#define LINK_OFF (0x0080)
#define ENDEC_LOOPBACK (0x0200)
#define AUI_LOOPBACK (0x0400)
#define BACKOFF_OFF (0x0800)
#define FDX_8900 (0x4000)
// PP_RxEvent - Receive Event Bit definition - Read-only
#define RX_IA_HASHED (0x0040)
#define RX_DRIBBLE (0x0080)
#define RX_OK (0x0100)
#define RX_HASHED (0x0200)
#define RX_IA (0x0400)
#define RX_BROADCAST (0x0800)
#define RX_CRC_ERROR (0x1000)
#define RX_RUNT (0x2000)
#define RX_EXTRA_DATA (0x4000)
#define HASH_INDEX_MASK (0xFC00) // Hash-Table Index Mask (6 Bit)
// PP_TxEvent - Transmit Event Bit definition - Read-only
#define TX_LOST_CRS (0x0040)
#define TX_SQE_ERROR (0x0080)
#define TX_OK (0x0100)
#define TX_LATE_COL (0x0200)
#define TX_JBR (0x0400)
#define TX_16_COL (0x8000)
#define TX_COL_COUNT_MASK (0x7800)
// PP_BufEvent - Buffer Event Bit definition - Read-only
#define SW_INTERRUPT (0x0040)
#define RX_DMA (0x0080)
#define READY_FOR_TX (0x0100)
#define TX_UNDERRUN (0x0200)
#define RX_MISS (0x0400)
#define RX_128_BYTE (0x0800)
#define TX_COL_OVRFLW (0x1000)
#define RX_MISS_OVRFLW (0x2000)
#define RX_DEST_MATCH (0x8000)
// PP_LineST - Ethernet Line Status bit definition - Read-only
#define LINK_OK (0x0080)
#define AUI_ON (0x0100)
#define TENBASET_ON (0x0200)
#define POLARITY_OK (0x1000)
#define CRS_OK (0x4000)
// PP_SelfST - Chip Software Status bit definition
#define ACTIVE_33V (0x0040)
#define INIT_DONE (0x0080)
#define SI_BUSY (0x0100)
#define EEPROM_PRESENT (0x0200)
#define EEPROM_OK (0x0400)
#define EL_PRESENT (0x0800)
#define EE_SIZE_64 (0x1000)
// PP_BusST - ISA Bus Status bit definition
#define TX_BID_ERROR (0x0080)
#define READY_FOR_TX_NOW (0x0100)
// The following block defines the ISQ event types
#define ISQ_RX_EVENT (0x0004)
#define ISQ_TX_EVENT (0x0008)
#define ISQ_BUFFER_EVENT (0x000c)
#define ISQ_RX_MISS_EVENT (0x0010)
#define ISQ_TX_COL_EVENT (0x0012)
#define ISQ_EVENT_MASK (0x003f) // ISQ mask to find out type of event
// Ports for I/O-Mode
#define RX_FRAME_PORT (0x0000)
#define TX_FRAME_PORT (0x0000)
#define TX_CMD_PORT (0x0004)
#define TX_LEN_PORT (0x0006)
#define ISQ_PORT (0x0008)
#define ADD_PORT (0x000a)
#define DATA_PORT (0x000c)
#define AUTOINCREMENT (0x8000) // Bit mask to set Bit-15 for autoincrement
// EEProm Commands
#define EEPROM_WRITE_EN (0x00f0)
#define EEPROM_WRITE_DIS (0x0000)
#define EEPROM_WRITE_CMD (0x0100)
#define EEPROM_READ_CMD (0x0200)
// Receive Header of each packet in receive area of memory for DMA-Mode
#define RBUF_EVENT_LOW (0x0000) // Low byte of RxEvent
#define RBUF_EVENT_HIGH (0x0001) // High byte of RxEvent
#define RBUF_LEN_LOW (0x0002) // Length of received data - low byte
#define RBUF_LEN_HI (0x0003) // Length of received data - high byte
#define RBUF_HEAD_LEN (0x0004) // Length of this header
// typedefs
typedef struct // struct to store CS8900's
{
unsigned int Addr; // init-sequence
unsigned int Data;
} TInitSeq;
// exported constants
extern const unsigned int MyMAC[]; // "M1-M2-M3-M4-M5-M6"
// exported functions
void Init8900(void);
void Write8900(unsigned char Address, unsigned int Data);
void WriteFrame8900(unsigned int Data);
unsigned int Read8900(unsigned char Address);
unsigned int ReadFrame8900(void);
unsigned int ReadHB1ST8900(unsigned char Address);
unsigned int ReadFrameBE8900(void);
void CopyToFrame8900(void *Source, unsigned int Size);
void CopyFromFrame8900(void *Dest, unsigned int Size);
void DummyReadFrame8900(unsigned int Size);
void RequestSend(unsigned int FrameSize);
unsigned int Rdy4Tx(void);
#endif
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -