rfc2331.txt

来自「RFC 的详细文档！」· 文本 代码 · 共 1,460 行 · 第 1/5 页

Network Working Group                                           M. Maher
Request for Comments: 2331                                       USC/ISI
Category: Standards Track                                     April 1998


   ATM Signalling Support for IP over ATM - UNI Signalling 4.0 Update

Status of this Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

Copyright Notice

   Copyright (C) The Internet Society (1998).  All Rights Reserved.

Abstract

   This memo describes how to efficiently use the ATM call control
   signalling procedures defined in UNI Signalling 4.0 [SIG40] to
   support IP over ATM environments as described in RFC 2225 [LAUB98]
   and in RFC 2332 [LUC98].  Among the new features found in UNI
   Signalling 4.0 are Available Bit Rate signalling and traffic
   parameter negotiation.  This memo highlights the features of UNI
   Signalling 4.0 that provide IP entities capabilities for requesting
   ATM service in sites with SVC support, whether it is private ATM or
   publicly provisioned ATM, in which case the SVC support is probably
   configured inside PVPs.

   This document is only relevant to IP when used as the well known
   "best effort" connectionless service. In particular, this means that
   this document does not pertain to IP in the presence of implemented
   IP Integrated Services.  The topic of IP with Integrated Services
   over ATM will be handled by a different specification or set of
   specifications being worked on in the ISSLL WG.

   This specification is a follow-on to RFC 1755, "ATM Signaling Support
   for IP over ATM", which is based on UNI 3.1 signalling [UNI95].
   Readers are assumed to be familiar with RFC 1755.









Maher                       Standards Track                     [Page 1]

RFC 2331        IP over ATM Signalling - SIG 4.0 Update       April 1998


Table of Contents

   1.  Conventions ...............................................   2
   2.  Overview ..................................................   2
   3.  Use of Protocol Procedures ................................   3
       3.1  VC Teardown...........................................   3
   4.  Overview of Call Establishment Message Content ............   3
   5.  Description of Information Elements .......................   4
       5.1  ATM Adaptation Layer Parameters ......................   4
       5.2  Broadband Low Layer Information  .....................   5
       5.3  Traffic Management Issues and Related IEs.............   5
            5.3.1  ATM Traffic Descriptor ........................   6
                   5.3.1.1  Tagging vs. Dropping .................   7
            5.3.2  Traffic Parameter Negotiation ..................  7
            5.3.3  Broadband Bearer Capability ....................  8
            5.3.4  QoS Parameter ..................................  8
                   5.3.4.1  Signalling of Individual QoS Parameters  8
       5.4  ATM Addressing Information ...........................   9
   6.  ABR Signalling In More Detail  ............................   9
   7.  Frame Discard Capability ..................................  10
   8.  Security Considerations ...................................  10
   9.  Acknowledgements...........................................  10
   10. References ................................................  10
   11. Author's Address ..........................................  12
   Appendix A  Sample Signalling Messages ........................  13
   Appendix B  ABR and nrt-VBR Signalling Guidelines for IP Routers 15
   Appendix C  Combinations of Traffic Related Parameters ........  18
   Full Copyright Statement ......................................  26

1.  Conventions

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119 [BRA97].

2.  Overview

   UNI Signalling version 4.0 (SIG 4.0) is the ATM Forum follow-on
   specification to UNI 3.1 signalling (UNI 3.1). Among the new features
   in SIG 4.0, those of particular interest to IP over ATM environments
   are:

        o Available Bit Rate (ABR) Signalling for Point-to-Point Calls
        o Traffic Parameter Negotiation
        o Frame Discard Support
        o Leaf Initiated Join (LIJ) Capability
        o ATM Anycast Capability
        o Switched Virtual Path (VP) Service



Maher                       Standards Track                     [Page 2]

RFC 2331        IP over ATM Signalling - SIG 4.0 Update       April 1998


   This memo highlights the first three capabilities listed above. The
   last three capabilities are not discussed because models for their
   use in IP over ATM environments have not yet been defined.  The ION
   WG is considering the applicability of LIJ and Group Addressing to
   the RFC2022 problem space.  Furthermore, Anycast addressing is being
   explored as a technique for supporting server discovery in ATM
   networks.

3.  Use of Protocol Procedures

   Section 3 in RFC 1755 introduces requirements of virtual circuit (VC)
   management intended to prevent VC thrashing, excessive VC
   consumption, and other related problems. This section updates RFC
   1755's requirements related to VC teardown.

3.1.  VC Teardown

   In environments running layer 3 (L3) signalling protocols, such as
   RSVP [RSVP], over ATM, data VCs might correspond to L3 reserved flows
   (even if the VC is a 'best effort' VC). In such environments it is
   beneficial for VCs to be torn down only when the L3 reservation has
   expired. In other words, it is more efficient for the sender of a L3
   reserved flow to initiate VC tear-down when the receiver(s) has
   ceased refreshing the reservation.  To support such L3 behavior,
   systems implementing a Public ATM UNI interface and serving as the
   _called_ party of a VCC MUST NOT use an inactivity timer on such a
   VCC by default.  A system MAY use an inactivity timer on such a VCC
   if configured to do so.

4.  Overview of Call Establishment Message Content

   Signalling messages are structured to contain mandatory and optional
   variable length information elements (IEs).  A SETUP message which
   establishes an ATM connection to be used for IP and multiprotocol
   interconnection calls MUST contain the following IEs:

        AAL Parameters
        ATM Traffic Descriptor
        Broadband Bearer Capability
        Broadband Low Layer Information
        QoS Parameter
        Called Party Number
        Calling Party Number

   and MAY, under certain circumstance contain the following IEs:






Maher                       Standards Track                     [Page 3]

RFC 2331        IP over ATM Signalling - SIG 4.0 Update       April 1998


        Calling Party Subaddress
        Called Party Subaddress
        Transit Network Selection

        (New in SIG 4.0:)
        Minimum Acceptable ATM Traffic Descriptor
        Alternative ATM Traffic Descriptor
        ABR Setup Parameters
        ABR Additional Parameters
        Connection Scope Selection
        Extended QoS Parameters
        End-to-End Transit Delay

   In SIG 4.0, like UNI 3.1, the AAL Parameters and the Broadband Low
   Layer Information IEs are optional in a SETUP message.  However, in
   support of IP over ATM these two IEs MUST be included. Appendix A
   shows a sample setup message.

5.  Description of Information Elements

   This section describes the coding of, and procedures surrounding,
   information elements in SETUP and CONNECT messages. The first two IEs
   described, ATM Adaptation Layer Parameters and Broadband Low Layer
   Information, are categorized as having significance only to the end-
   points of an ATM call supporting IP. That is, the network does not
   process these IEs.

5.1.  ATM Adaptation Layer (AAL) Parameters

   The AAL Parameters IE carries information about the ATM adaptation
   layer to be used on the connection. The parameters specified in this
   IE are the same as specified in [PER95].


       Format and field values of AAL Parameters IE

       ----------------------------------------------------------
       | aal_parameters                                         |
       ----------------------------------------------------------
       |  aal_type                    5        (AAL 5)          |
       |  fwd_max_sdu_size_identifier 140                       |
       |  fwd_max_sdu_size            65,535   (desired IP MTU) |
       |  bkw_max_sdu_size_identifier 129                       |
       |  bkw_max_sdu_size            65,535   (desired IP MTU) |
       |  sscs_type identifier        132                       |
       |  sscs_type                   0        (null SSCS)      |
       ----------------------------------------------------------




Maher                       Standards Track                     [Page 4]

RFC 2331        IP over ATM Signalling - SIG 4.0 Update       April 1998


   This shows maximum size MTUs.  In practice, most sites have used 9180
   IP MTUs for ATM [RFC1626].

5.2.  Broadband Low Layer Information

   Selection of an encapsulation to support IP over an ATM VCC is done
   using the Broadband Low Layer Information (B-LLI) IE, along with the
   AAL Parameters IE, and the B-LLI negotiation procedure.  B-LLI
   negotiation is described in [PER95] in Appendix D. The procedures
   remain the same for this SIG 4.0 based specification.

       Format of B-LLI IE indicating LLC/SNAP encapsulation

       ----------------------------------------------------------
       | bb_low_layer_information                               |
       ----------------------------------------------------------
       |  layer_2_id                 2                          |
       |  user_information_layer     12  (lan_llc - ISO 8802/2) |
       ----------------------------------------------------------

5.3.  Traffic Management Issues and Related IEs

   The ATM Forum Traffic Management Sub-working group has completed
   version 4.0 of their specification [TMGT40]. This latest version
   focuses primarily on the definition of the ABR service category. As
   opposed to the Unspecified Bit Rate (UBR) traffic class, ABR uses a
   rate-based flow control mechanism to assure certain traffic
   guarantees (bandwidth and delay).  There has been much debate on
   whether IP benefits from ABR, and if so, how IP should use ABR. The
   IP Integrated Services (IIS) and RSVP models in IP add complexity to
   this issue because mapping IIS traffic classes to ATM traffic classes
   is not straightforward.

   This document attempts only to present the required IP to ATM
   signaling interface for IP over ATM systems that do not support IIS
   as yet.  It is an attempt to cause IP over ATM vendors to support
   enough options for signalling the traffic characteristics of VCs
   serving non-IIS IP datagrams. This specification also aims to give
   guidance to ATM system administrators so that they can configure
   their IP over ATM entities to conform to the varied services that
   their ATM provider may have sold to them.  By definition, IP without
   IIS cannot be expected to provide a signalling interface that is
   flexible and allows application specific traffic descriptors. The
   topic of IP over ATM signalling for IP _with_ IIS is to be presented
   in other specifications being produced by the ISSLL WG of the IETF.

   An IP over ATM interface may be configured to support all the defined
   ATM Service Categories (ASC). They are:



Maher                       Standards Track                     [Page 5]

RFC 2331        IP over ATM Signalling - SIG 4.0 Update       April 1998


    - CBR
    - CBR with CLR specified (loss-permitting CBR)
    - ABR
    - UBR
    - real time VBR
    - non-real time VBR