rfc2461.txt
来自「RFC 的详细文档！」· 文本 代码 · 共 1,451 行 · 第 1/5 页
TXT
1,451 行
variable MTU - Neighbor Discovery allows routers to specify a MTU
for the link, which all nodes then use. All nodes
on a link must use the same MTU (or Maximum
Receive Unit) in order for multicast to work
properly. Otherwise when multicasting a sender,
which can not know which nodes will receive the
packet, could not determine a minimum packet size
all receivers can process.
asymmetric reachability
- Neighbor Discovery detects the absence of
symmetric reachability; a node avoids paths to a
neighbor with which it does not have symmetric
connectivity.
The Neighbor Unreachability Detection will
typically identify such half-links and the node
will refrain from using them.
The protocol can presumably be extended in the
future to find viable paths in environments that
Narten, et. al. Standards Track [Page 16]
RFC 2461 Neighbor Discovery for IPv6 December 1998
lack reflexive and transitive connectivity.
4. MESSAGE FORMATS
4.1. Router Solicitation Message Format
Hosts send Router Solicitations in order to prompt routers to
generate Router Advertisements quickly.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Code | Checksum |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Options ...
+-+-+-+-+-+-+-+-+-+-+-+-
IP Fields:
Source Address
An IP address assigned to the sending interface, or
the unspecified address if no address is assigned
to the sending interface.
Destination Address
Typically the all-routers multicast address.
Hop Limit 255
Authentication Header
If a Security Association for the IP Authentication
Header exists between the sender and the
destination address, then the sender SHOULD include
this header.
ICMP Fields:
Type 133
Code 0
Checksum The ICMP checksum. See [ICMPv6].
Reserved This field is unused. It MUST be initialized to
zero by the sender and MUST be ignored by the
receiver.
Narten, et. al. Standards Track [Page 17]
RFC 2461 Neighbor Discovery for IPv6 December 1998
Valid Options:
Source link-layer address
The link-layer address of the sender, if known.
MUST NOT be included if the Source Address is the
unspecified address. Otherwise it SHOULD be
included on link layers that have addresses.
Future versions of this protocol may define new option types.
Receivers MUST silently ignore any options they do not recognize
and continue processing the message.
4.2. Router Advertisement Message Format
Routers send out Router Advertisement message periodically, or in
response to a Router Solicitation.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Code | Checksum |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Cur Hop Limit |M|O| Reserved | Router Lifetime |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reachable Time |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Retrans Timer |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Options ...
+-+-+-+-+-+-+-+-+-+-+-+-
IP Fields:
Source Address
MUST be the link-local address assigned to the
interface from which this message is sent.
Destination Address
Typically the Source Address of an invoking Router
Solicitation or the all-nodes multicast address.
Hop Limit 255
Authentication Header
If a Security Association for the IP Authentication
Header exists between the sender and the
destination address, then the sender SHOULD include
this header.
Narten, et. al. Standards Track [Page 18]
RFC 2461 Neighbor Discovery for IPv6 December 1998
ICMP Fields:
Type 134
Code 0
Checksum The ICMP checksum. See [ICMPv6].
Cur Hop Limit 8-bit unsigned integer. The default value that
should be placed in the Hop Count field of the IP
header for outgoing IP packets. A value of zero
means unspecified (by this router).
M 1-bit "Managed address configuration" flag. When
set, hosts use the administered (stateful) protocol
for address autoconfiguration in addition to any
addresses autoconfigured using stateless address
autoconfiguration. The use of this flag is
described in [ADDRCONF].
O 1-bit "Other stateful configuration" flag. When
set, hosts use the administered (stateful) protocol
for autoconfiguration of other (non-address)
information. The use of this flag is described in
[ADDRCONF].
Reserved A 6-bit unused field. It MUST be initialized to
zero by the sender and MUST be ignored by the
receiver.
Router Lifetime
16-bit unsigned integer. The lifetime associated
with the default router in units of seconds. The
maximum value corresponds to 18.2 hours. A
Lifetime of 0 indicates that the router is not a
default router and SHOULD NOT appear on the default
router list. The Router Lifetime applies only to
the router's usefulness as a default router; it
does not apply to information contained in other
message fields or options. Options that need time
limits for their information include their own
lifetime fields.
Reachable Time 32-bit unsigned integer. The time, in
milliseconds, that a node assumes a neighbor is
reachable after having received a reachability
confirmation. Used by the Neighbor Unreachability
Detection algorithm (see Section 7.3). A value of
Narten, et. al. Standards Track [Page 19]
RFC 2461 Neighbor Discovery for IPv6 December 1998
zero means unspecified (by this router).
Retrans Timer 32-bit unsigned integer. The time, in
milliseconds, between retransmitted Neighbor
Solicitation messages. Used by address resolution
and the Neighbor Unreachability Detection algorithm
(see Sections 7.2 and 7.3). A value of zero means
unspecified (by this router).
Possible options:
Source link-layer address
The link-layer address of the interface from which
the Router Advertisement is sent. Only used on
link layers that have addresses. A router MAY omit
this option in order to enable inbound load sharing
across multiple link-layer addresses.
MTU SHOULD be sent on links that have a variable MTU
(as specified in the document that describes how to
run IP over the particular link type). MAY be sent
on other links.
Prefix Information
These options specify the prefixes that are on-link
and/or are used for address autoconfiguration. A
router SHOULD include all its on-link prefixes
(except the link-local prefix) so that multihomed
hosts have complete prefix information about on-
link destinations for the links to which they
attach. If complete information is lacking, a
multihomed host may not be able to choose the
correct outgoing interface when sending traffic to
its neighbors.
Future versions of this protocol may define new option types.
Receivers MUST silently ignore any options they do not recognize
and continue processing the message.
Narten, et. al. Standards Track [Page 20]
RFC 2461 Neighbor Discovery for IPv6 December 1998
4.3. Neighbor Solicitation Message Format
Nodes send Neighbor Solicitations to request the link-layer address
of a target node while also providing their own link-layer address to
the target. Neighbor Solicitations are multicast when the node needs
to resolve an address and unicast when the node seeks to verify the
reachability of a neighbor.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Code | Checksum |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ +
| |
+ Target Address +
| |
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Options ...
+-+-+-+-+-+-+-+-+-+-+-+-
IP Fields:
Source Address
Either an address assigned to the interface from
which this message is sent or (if Duplicate Address
Detection is in progress [ADDRCONF]) the
unspecified address.
Destination Address
Either the solicited-node multicast address
corresponding to the target address, or the target
address.
⌨️ 快捷键说明
复制代码Ctrl + C
搜索代码Ctrl + F
全屏模式F11
增大字号Ctrl + =
减小字号Ctrl + -
显示快捷键?