📄 rfc1695.txt
字号:
VCC AAL5 CPCS |(1)PDUs discarded for CRC errors |ATM MIB| |
layer: |(2)PDUs discarded due to | gr.6 | |
performance | reassembly time out | |no |
|(3)PDUs discarded due to large | | |
| SDUs | | |
_____________________________________________________________
AAL5 entity: |(1)received/transmitted PDUs | | |
|(2)PDUs discarded due to | | |
| protocol errors |MIB II |no |
|(3)a set of configuration/state | | |
| parameters | | |
_____________________________________________________________
*The operational, administrative, and last change status of
the ATM interface and the physical transmission type shall be
supported by the interface table in MIB II (RFC 1213, RFC
1573). ILMI does not contain the administrative and last
change status of the ATM interface.
** The ILMI MIB does not contain information on the ATM
address type and the ATM administrative address assigned at
the ATM interface.
***The ILMI MIB contains local and end-to-end operational
status of the VPC/VCC segment. However, it does not contain
the VPC/VCC administrative and last change status and the VCC
AAL information.
Ahmed & Tesink [Page 17]
RFC 1695 ATM Management Objects August 1994
10. Definitions
ATM-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, OBJECT-IDENTITY,
Counter32, Integer32, IpAddress
FROM SNMPv2-SMI
TEXTUAL-CONVENTION, DisplayString,
TimeStamp, RowStatus
FROM SNMPv2-TC
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
ifIndex, mib-2
FROM RFC1213-MIB;
atmMIB MODULE-IDENTITY
LAST-UPDATED "9406072245Z"
ORGANIZATION "IETF AToM MIB Working Group"
CONTACT-INFO
" Masuma Ahmed
Postal: Bellcore
331 Newman Springs Road
Red Bank, NJ 07701
US
Tel: +1 908 758 2515
Fax: +1 908 758 4131
E-mail: mxa@mail.bellcore.com
Kaj Tesink
Postal: Bellcore
331 Newman Springs Road
Red Bank, NJ 07701
US
Tel: +1 908 758 5254
Fax: +1 908 758 4196
E-mail: kaj@cc.bellcore.com"
DESCRIPTION
"This is the MIB Module for ATM and AAL5-related
objects for managing ATM interfaces, ATM virtual
links, ATM cross-connects, AAL5 entities, and
and AAL5 connections."
::= { mib-2 37 }
atmMIBObjects OBJECT IDENTIFIER ::= {atmMIB 1}
-- This ATM MIB Module consists of the following groups:
Ahmed & Tesink [Page 18]
RFC 1695 ATM Management Objects August 1994
-- (1) ATM Interface configuration group
-- (2) ATM Interface DS3 PLCP group
-- (3) ATM Interface TC Sublayer group
-- (4) ATM Interface VPL configuration group
-- (5) ATM Interface VCL configuration group
-- (6) ATM VP Cross Connect group
-- (7) ATM VC Cross Connect group
-- (8) ATM Interface AAL5 VCC performance statistics
-- group
IfIndex ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The value of this object identifies the interface
for which the entry contains management
information. The value of this object for a
particular interface has the same value as the
ifIndex object, defined in RFC 1213, for the same
interface."
SYNTAX Integer32
AtmTrafficDescrParamIndex ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The value of this object identifies the row
in the atmTrafficDescrParamTable."
SYNTAX Integer32
atmTrafficDescriptorTypes OBJECT IDENTIFIER ::=
{atmMIBObjects 1}
-- The following values are defined for use as
-- possible values of the ATM traffic descriptor type.
-- ATM Forum specified seven types of ATM traffic
-- descriptors.
atmNoTrafficDescriptor OBJECT-IDENTITY
STATUS current
DESCRIPTION
"This identifies the no ATM traffic descriptor
type. Parameters 1, 2, 3, 4, and 5 are not used.
This traffic descriptor type can be used for
best effort traffic."
::= { atmTrafficDescriptorTypes 1}
atmNoClpNoScr OBJECT-IDENTITY
Ahmed & Tesink [Page 19]
RFC 1695 ATM Management Objects August 1994
STATUS current
DESCRIPTION
"This traffic descriptor is for no CLP and
no Sustained Cell Rate. The use of the
parameter vector for this type:
Parameter 1: CLP=0+1 peak cell rate in
cells per second
Parameter 2: not used
Parameter 3: not used
Parameter 4: not used
Parameter 5: not used.
This traffic descriptor type can be used
for best effort traffic."
::= { atmTrafficDescriptorTypes 2}
atmClpNoTaggingNoScr OBJECT-IDENTITY
STATUS current
DESCRIPTION
"This traffic descriptor is for no CLP without
tagging and no Sustained Cell Rate. The use
of the parameter vector for this type:
Parameter 1: CLP=0+1 peak cell rate in
cells per second
Parameter 2: CLP=0 peak cell rate in
cells per second
Parameter 3: not used
Parameter 4: not used
Parameter 5: not used."
::= { atmTrafficDescriptorTypes 3}
atmClpTaggingNoScr OBJECT-IDENTITY
STATUS current
DESCRIPTION
"This traffic descriptor is for CLP with
tagging and no Sustained Cell Rate. The
use of the parameter vector for this type:
Parameter 1: CLP=0+1 peak cell rate in
cells per second
Parameter 2: CLP=0 peak cell rate in
cells per second with excess
traffic tagged as CLP=1
Parameter 3: not used
Parameter 4: not used
Parameter 5: not used."
::= { atmTrafficDescriptorTypes 4}
atmNoClpScr OBJECT-IDENTITY
STATUS current
Ahmed & Tesink [Page 20]
RFC 1695 ATM Management Objects August 1994
DESCRIPTION
"This traffic descriptor is for no CLP
with Sustained Cell Rate. The
use of the parameter vector for this type:
Parameter 1: CLP=0+1 peak cell rate in
cells per second
Parameter 2: CLP=0+1 sustained cell rate in
cells per second
Parameter 3: CLP=0+1 maximum burst size
in cells
Parameter 4: not used
Parameter 5: not used."
::= { atmTrafficDescriptorTypes 5}
atmClpNoTaggingScr OBJECT-IDENTITY
STATUS current
DESCRIPTION
"This traffic descriptor is for CLP
with Sustained Cell Rate and no tagging.
The use of the parameter vector for this type:
Parameter 1: CLP=0+1 peak cell rate in
cells per second
Parameter 2: CLP=0 sustained cell rate in
cells per second
Parameter 3: CLP=0 maximum burst size in cells
Parameter 4: not used
Parameter 5: not used."
::= { atmTrafficDescriptorTypes 6}
atmClpTaggingScr OBJECT-IDENTITY
STATUS current
DESCRIPTION
"This traffic descriptor is for CLP
with tagging and Sustained Cell Rate.
The use of the parameter vector for this type:
Parameter 1: CLP=0+1 peak cell rate in
cells per second
Parameter 2: CLP=0 sustained cell rate in
cells per second with excess
traffic tagged as CLP=1
Parameter 3: CLP=0 maximum burst size in cells
Parameter 4: not used
Parameter 5: not used."
::= { atmTrafficDescriptorTypes 7}
-- ATM Interface Configuration Parameters Group
Ahmed & Tesink [Page 21]
RFC 1695 ATM Management Objects August 1994
-- This group contains ATM specific
-- configuration information associated with
-- an ATM interface beyond those
-- supported using the ifTable.
atmInterfaceConfTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmInterfaceConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains ATM local interface
configuration parameters, one entry per ATM
interface port."
::= { atmMIBObjects 2 }
atmInterfaceConfEntry OBJECT-TYPE
SYNTAX AtmInterfaceConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This list contains ATM interface configuration
parameters and state variables."
INDEX { ifIndex }
::= { atmInterfaceConfTable 1}
AtmInterfaceConfEntry ::= SEQUENCE {
atmInterfaceMaxVpcs INTEGER,
atmInterfaceMaxVccs INTEGER,
atmInterfaceConfVpcs INTEGER,
atmInterfaceConfVccs INTEGER,
atmInterfaceMaxActiveVpiBits INTEGER,
atmInterfaceMaxActiveVciBits INTEGER,
atmInterfaceIlmiVpi INTEGER,
atmInterfaceIlmiVci INTEGER,
atmInterfaceAddressType INTEGER,
atmInterfaceAdminAddress OCTET STRING,
atmInterfaceMyNeighborIpAddress IpAddress,
atmInterfaceMyNeighborIfName DisplayString
}
atmInterfaceMaxVpcs OBJECT-TYPE
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -