rfc1377.txt

来自「RFC 的详细文档！」· 文本 代码 · 共 563 行 · 第 1/2 页

Network Working Group                                            D. Katz
Request for Comments: 1377                                         cisco
                                                           November 1992


          The PPP OSI Network Layer Control Protocol (OSINLCP)

Status of this Memo

   This RFC specifies an IAB standards track protocol for the Internet
   community, and requests discussion and suggestions for improvements.
   Please refer to the current edition of the "IAB Official Protocol
   Standards" for the standardization state and status of this protocol.
   Distribution of this memo is unlimited.

Abstract

   The Point-to-Point Protocol (PPP) [1] provides a standard method of
   encapsulating Network Layer protocol information over point-to-point
   links.  PPP also defines an extensible Link Control Protocol, and
   proposes a family of Network Control Protocols (NCPs) for
   establishing and configuring different network-layer protocols.

   This document defines the NCP for establishing and configuring OSI
   Network Layer Protocols.

   This memo is the product of the Point-to-Point Protocol Working Group
   of the Internet Engineering Task Force (IETF).  Comments on this memo
   should be submitted to the [e-mail] mailing list.

Table of Contents

   1.     Introduction ..........................................    2
   1.1    OSI Network Layer Protocols over PPP ..................    2
   2.     A PPP Network Control Protocol (NCP) for OSI ..........    5
   2.1    Sending OSI NPDUs .....................................    6
   2.2    NPDU Alignment ........................................    6
   2.3    Network Layer Addressing Information ..................    6
   3.     OSINLCP Configuration Options .........................    7
   3.1    Align-NPDU ............................................    7
   REFERENCES ...................................................    9
   ACKNOWLEDGEMENTS .............................................    9
   SECURITY CONSIDERATIONS ......................................   10
   CHAIR'S ADDRESS ..............................................   10
   AUTHOR'S ADDRESS .............................................   10






Katz                                                            [Page 1]

RFC 1377                      PPP OSINLCP                  November 1992


1.  Introduction

   PPP has three main components:

      1. A method for encapsulating datagrams over serial links.

      2. A Link Control Protocol (LCP) for establishing, configuring,
         and testing the data-link connection.

      3. A family of Network Control Protocols (NCPs) for establishing
         and configuring different network-layer protocols.

   In order to establish communications over a point-to-point link, each
   end of the PPP link must first send LCP packets to configure and test
   the data link.  After the link has been established and optional
   facilities have been negotiated as needed by the LCP, PPP must send
   NCP packets to choose and configure one or more network-layer
   protocols.  Once each of the chosen network-layer protocols has been
   configured, datagrams from each network-layer protocol can be sent
   over the link.

   The link will remain configured for communications until explicit LCP
   or NCP packets close the link down, or until some external event
   occurs (an inactivity timer expires or network administrator
   intervention).

1.1.  OSI Network Layer Protocols over PPP

   A number of protocols have been defined for the Network Layer of OSI,
   including the Connectionless Network Layer Protocol (CLNP, ISO 8473)
   [3], the End System to Intermediate System routing protocol (ES-IS,
   ISO 9542) [4], the Intermediate System to Intermediate System routing
   protocol (IS-IS, ISO 10589) [5], and the Inter-Domain Routeing
   Protocol (IDRP, CD 10747) [6].  Generally, these protocols were
   designed to run over non-reliable data link protocols such as PPP.

   Network Layer Protocol Identifier (NLPID)

      OSI Network Layer protocols can be discriminated according to the
      first octet in each Network Protocol Data Unit (NPDU, that is,
      packet), known as the Network Layer Protocol Identifier (NLPID),
      which is defined in ISO/TR 9577 [7].  This allows the various
      protocols to be run over a common data link without any
      discriminator below the network layer.







Katz                                                            [Page 2]

RFC 1377                      PPP OSINLCP                  November 1992


   Inactive Network Layer Protocol

      ISO/TR 9577 reserves a NLPID value of zero to represent the
      "Inactive Network Layer Protocol", as defined in ISO 8473.  The
      inactive network layer protocol MUST NOT be used over PPP.  This
      assures that whichever OSI network layer protocol is used will
      have a non-zero NLPID value.

   Connection-Oriented Network Protocol

      The OSI Connection-Oriented Network Protocol (ISO 8208) [8],
      effectively the Packet Layer of CCITT X.25, is intended to be run
      over a reliable data link, such as IEEE 802.2 type II or LAPB.
      Therefore, the unreliable data link service provided by PPP is not
      appropriate for use with ISO 8208.

   ConnectionLess Network Protocol (CLNP)

      The ConnectionLess Network Protocol offers a simple non-reliable
      datagram service very similar to IP, and is designed to run over a
      non-reliable data link service, such as provided by PPP.

   End-System to Intermediate-System Protocol (ES-IS)

      ES Hellos and IS Hellos are retransmitted on a periodic timer-
      driven basis (based on expiration of the "Configuration Timer").
      The resulting ES and IS configuration information is invalidated
      on a timer driven basis, based on expiration of the "Holding
      Timer" for each piece of information.  The value of a Holding
      Timer is set by the source of the information, and transmitted in
      the Holding Time field of the appropriate ES-IS packet.  ISO 9542
      recommends that the holding time field is set to approximately
      twice the Configuration Timer parameter, such that even if every
      other Hello packet is lost the configuration information will be
      retained (implying that the Holding Timer is actually set to
      slightly more than twice the Configuration Timer).

      Generally, the recommendation in ISO 9542 is sufficient for PPP
      links.  For very unreliable links, it may be necessary to set the
      Holding Timer to be slightly more than three times the
      Configuration Timer to ensure that loss of configuration
      information is an unusual event.

      Redirect information is not transmitted on point-to-point links,
      but may be transmitted on general topology subnetworks, which in
      turn may make use of PPP.  Redirect information is sent on a
      event-driven basis (based on a CLNP packet being forwarded by a
      router out the incoming interface), but redirect information is



Katz                                                            [Page 3]

RFC 1377                      PPP OSINLCP                  November 1992


      invalidated on a timer-driven basis.  Loss of a single redirect
      may result in a subsequent data packet being sent to the same
      incorrect router, which will re-issue the redirect.  This operates
      in the same manner as ICMP redirects for IP packets, and does not
      pose any problem for operation over PPP links.

   Intermediate-System to Intermediate-System Protocol (IS-IS)

      IS-IS allows for broadcast links (typically LANs), point-to-point
      links (such as PPP), and general topology links (such as X.25
      networks) which are modelled as a collection of point-to-point
      links.

      There are four types of IS-IS packets: IS-IS Hello Packets, Link
      State Packets (LSPs), Complete Sequence Number Packets (CSNPs),
      and Partial Sequence Number Packets (PSNPs).

      IS-IS Hello messages are transmitted periodically on point-to-
      point links (based on expiration of the "ISISHello" timer).
      Routers expect to receive IS-IS Hello packets periodically.
      Specifically, the IS-IS Hello packet specifies a "Holding Time".
      If no subsequent IS-IS Hello is received over the corresponding
      link for the specified time period, then the neighboring router is
      assumed to have been disconnected or to be down.  It is highly
      undesireable for links to "flap" up and down unnecessarily, which
      implies that the holding time needs to be large enough that a link
      is very unlikely to be declared down due to a failure to receive
      an IS-IS Hello.  This implies that running IS-IS over unreliable
      data links requires the Holding time to be greater than "k" times
      the ISISHello timer, where k is chosen such that the loss of k
      consecutive IS-IS Hello's is rare.  If the quality of the link is
      poor, then the Holding Time will need to be increased or the
      "ISISHello" time decreased.

      LSPs are acknowledged by the IS-IS protocol (via use of partial
      sequence number packets).  A lost LSP will be recovered from with
      no problem provided that PPP links are treated the same way as
      other point-to-point links.  On those rare occasions where a
      partial sequence number packet is lost, this might result in the
      retransmission of a link state packet over a single link, but will
      not impact the correct operation of the routing algorithm.

      CSNPs are sent upon link startup on a point-to-point link.  This
      does not need to be changed for PPP.  If a CSNP fragment is lost
      upon startup it is merely loss of an optimization -- LSPs that did
      not need to be transmitted over the link will be transmitted.  If
      a periodic CSNP fragment is lost it merely means that detection of
      low probability database corruption will take longer.



Katz                                                            [Page 4]

RFC 1377                      PPP OSINLCP                  November 1992


      PSNPs function as ACKs.  Loss of a PSNP may result in an
      unnecessary retransmission of an LSP, but does not prevent correct
      operation of the routing protocol.

   Inter-Domain Routeing Protocol (IDRP)

      IDRP expects to run over datagram links, but requires reliable
      exchange of IDRP information.  For this reason, IDRP contains
      built-in reliability mechanisms which ensure that packets will be
      received correctly.

2.  A PPP Network Control Protocol (NCP) for OSI

   The OSI Network Layer Control Protocol (OSINLCP) is responsible for
   configuring, enabling, and disabling the OSI protocol modules on both
   ends of the point-to-point link.  OSINLCP uses the same packet
   exchange machanism as the Link Control Protocol (LCP).  OSINLCP
   packets may not be exchanged until PPP has reached the Network-Layer
   Protocol phase.  OSINLCP packets received before this phase is
   reached should be silently discarded.

   The OSI Network Layer Control Protocol is exactly the same as the
   Link Control Protocol [1] with the following exceptions:

   Frame Modifications

      The packet may utilize any modifications to the basic frame format
      which have been negotiated during the Link Establishment phase.

   Data Link Layer Protocol Field

      Exactly one OSINLCP packet is encapsulated in the Information
      field of a PPP Data Link Layer frame where the Protocol field
      indicates type hex 8023 (OSI Network Layer Control Protocol).

   Code field

      Only Codes 1 through 7 (Configure-Request, Configure-Ack,
      Configure-Nak, Configure-Reject, Terminate-Request, Terminate-Ack
      and Code-Reject) are used.  Other Codes should be treated as
      unrecognized and should result in Code-Rejects.

   Timeouts

      OSINLCP packets may not be exchanged until PPP has reached the
      Network-Layer Protocol phase.  An implementation should be
      prepared to wait for Authentication and Link Quality Determination
      to finish before timing out waiting for a Configure-Ack or other



Katz                                                            [Page 5]