📄 rfc1069.txt
字号:
Network Working Group R. Callon
Request for Comments: 1069 DEC
Obsoletes: RFC 986 H.W. Braun
UMich
February 1989
Guidelines for the use of Internet-IP addresses in the
ISO Connectionless-Mode Network Protocol
Status of This Memo
This RFC suggests an addressing scheme for use with the ISO
Connectionless Network Protocol (CLNP) in the Internet. This is a
solution to one of the problems inherent in the use of "ISO-grams" in
the Internet. This RFC suggests a proposed protocol for the Internet
community, and requests discussion and suggestions for improvements.
Distribution of this memo is unlimited.
This memo is a revision of RFC 986. Changes were made in order to
allow the addressing used in the CLNP in the Internet to be
potentially useful for routing in the context of new inter- and
intra-domain routing protocols, and in the context of large numbers
of networks and routing domains. The addressing scheme proposed in
this RFC allows individual routing domains to make use of internal
routing algorithms utilizing a variety of addressing formats, while
still providing for a common addressing approach for use by inter-
domain routing. These features are important due to the rapid growth
currently being experienced in the Internet.
1. Objectives
The data communications protocols currently emerging out of the
international standardization efforts warrant an early integration
into the existing extensive Internet network infrastructure. The two
possible approaches are a top-down one, where ISO applications like
FTAM, X.400 and VTP are integrated on top of the transport function
of the IP protocol suite, or a bottom-up approach where the whole ISO
tower gets integrated without merging the two suites. The bottom-up
approach may make use of the fact that the ISO-CLNP and the IP are
very similar in function. This implies that it is reasonable to
implement a multiprotocol function in some or all of the Internet
gateways (potentially including part or all of the Internet
environment). The result would be that at least large portions of
the Internet, in particular the backbones, can become usable for full
implementations of the ISO protocol stack.
A major problem with this approach is that there are open issues with
Callon & Braun [Page 1]
RFC 1069 IP ISO Addressing February 1989
regard to the ISO addressing within the CLNP. In particular, the ISO
network layer addressing standard allows a great deal of flexibility
in the assignment of addresses, and a particular address format must
be chosen. A further problem is the need for implementation and
integration of routing facilities for the ISO-compatible subset of
the Internet environment.
This paper proposed to use addresses which are considerably more
flexible than the addresses used in the current IP Internet
environment. This flexibility is necessary in order to allow some
routing domains to base their internal routing protocol on addresses
derived from the current IP addresses, to allow other routing domains
to base routing on addresses in accordance to the intra-domain
routing protocol being developed by ANSI and ISO [6], and to allow
generality for a future inter-domain routing protocol.
The addressing scheme proposed here makes use of the concept of
"routing domains" as used in ANSI and ISO. This concept is similar
to, but not identical with, the concept of "Autonomous System" used
in the Internet. Routing domains include a combination of gateways,
networks, and end systems (not just gateways), and routing domain
boundaries may be used to define associated access control and policy
routing constraints. Like autonomous systems, routing domains may be
assumed to be topologically contiguous. There is no a priori reason
why routing domains assigned for use with the ISO IP need to have any
particular relation with existing autonomous systems which have been
assigned for use with the IP. The assignment of specific routing
domain identifiers is an "assigned numbers" function which is
necessary for use of the ISO IP in the Internet, but is beyond the
scope of this document.
It is expected that this addressing scheme will be appropriate for
long term use with the ISO IP in the Internet. However, it is also
expected that in the long term, the Internet will be interconnected
with other routing domains making use of other schemes, such as
addresses assigned to commercial internets through ANSI, and
addresses assigned by national standards organizations in other
countries. This implies that, in the long term, gateways in the
Internet will need to be able to route datagrams to destinations in
other routing domains not conforming to the addressing format
proposed here. This is discussed in greater detail in section 6.
2. Introduction
The CLNP is documented in [1], but for matters of completeness the
following illustration of the CLNP header is included here as Figure
1.
Callon & Braun [Page 2]
RFC 1069 IP ISO Addressing February 1989
The addressing part of the header is the subject of this RFC, i.e.,
the source and the destination address, respectively. These
addresses are generally discussed in [2] and [3], with this document
presenting a specific method for addressing in the Internet
environment, consistent with the international standardized NSAP
addresses.
Octet
+--------------------------------------+ +--------
| Network Layer Protocol Identifier | 1 :
|--------------------------------------| :
| Length Indicator | 2 :
|--------------------------------------| :
| Version/Protocol Id Extension | 3 : Fixed
|--------------------------------------| :
| Lifetime | 4 : Part
|--------------------------------------| :
|SP|MS|E/R| Type | 5 :
|--------------------------------------| :
| Segment Length | 6,7 :
|--------------------------------------| :
| Checksum | 8,9 :
|--------------------------------------| +--------
| Destination Address Length Indicator | 10 :
|--------------------------------------| :
| Destination Address | 11 through m-1 : Address
|--------------------------------------| :
| Source Address Length Indicator | m : Part
|--------------------------------------| :
| Source Address | m+1 through n-1 :
|--------------------------------------| +--------
| Data Unit Identifier | n,n+1 :
|--------------------------------------| : Segment
| Segment Offset | n+2,n+3 : ation
|--------------------------------------| :
| Total Length | n+4,n+5 : Part
|--------------------------------------| +--------
| Options | n+6 through p : Options
Part
|--------------------------------------| +--------
| Data | p+1 through z : Data
+--------------------------------------+ +--------
Figure 1: PDU Header Format
Callon & Braun [Page 3]
RFC 1069 IP ISO Addressing February 1989
3. Addresses for Use in the Internet
This section describes the addresses used to address NSAPs in the
Internet.
The appropriate Authority and Format Identifier (AFI) is one octet in
length. It specifies an ISO-6523-ICD assignment, and also that the
Domain Specific Part (DSP) of the address is based on binary. The
AFI octet uses the value "47". The ISO-6523-ICD format is used to
emphasize that this is an administrative assignment. The usage of an
ISO DCC (Data Country Code) would be possible, but could be
misleading due to the fairly far spread geographical extent of the
Internet.
As required by the ISO addressing standard, the next two octets of
the address, in this case, specify the Initial Domain Identifier.
This two octet value is the International Code Designator (ICD)
assigned to the Internet, "0006".
The remainder of the NSAP address is the Domain Specific Part (DSP).
This is assigned by the Internet administration, which is considered
to be an addressing domain. Note that there is no particular
relationship required between addressing domains and routing domains.
In this case, although the Internet is considered to be a single
addressing domain, it is expected that it will consist of multiple
routing domains.
The DSP of the address specifies a one octet version number, a two
octet global area number, a two octet routing domain number, a
variable length padding field, a variable length IGP specific part,
and a one octet selector field.
The version number is provided to allow for future extensions, and
must contain the value "02".
The global area number and routing domain number are provided to
allow for inter-domain routing. Initially, the global area number is
reserved and must be set to zero. The routing domain number may be
set to the routing domain number of any gateway by which the
associated host address is directly reachable.
The IGP specific part of the address may contain whatever addressing
format is used in the routing domain. Two particular formats are
expected to be used initially, and are presented in section 4.
Padding is used so that the entire address will always be 20 octets
in length.
The selector field performs the same function as the user protocol
Callon & Braun [Page 4]
RFC 1069 IP ISO Addressing February 1989
field in the IP header. This is necessary because the ISO protocol
considers identification of the user protocol to be an addressing
issue, and therefore does not allow for the user protocol to be
specified in the protocol header independently from the address.
The assignment of specific routing domain identifiers to defined
routing domains, and the assignment of values for use in the selector
field, are functions for the Assigned Numbers authority for the
Internet [4]. The specific values to be used are outside of the
scope of this document.
In summary, a source or destination address within the ISO
Connectionless Protocol, when used in the Internet, looks as follows:
Octet
+------------------------+
| AFI | 1
+------------------------+
| IDI / ICD | 2
+-- --+
|(specifies DoD Internet)| 3
+------------------------+
| Version Number | 4
+------------------------+
| Global Area | 5
+--- ---+
| Number | 6
+------------------------+
| Routing | 7
+--- ---+
| Domain | 8
+------------------------+
| | 9
: Padding : :
: : :
| | n
+------------------------+
| IGP | n+1
: : :
: : :
| Specific | 19
+------------------------+
| Selector | 20
+------------------------+
Figure 2: ISO IP address structure
Callon & Braun [Page 5]
⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -