8139.h

RTL8139驱动源码

/* Symbolic offsets to registers. */
enum RTL8139_registers {
	MAC0 = 0,		/* Ethernet hardware address. */
	MAR0 = 8,		/* Multicast filter. */
	TxStatus0 = 0x10,	/* Transmit status (Four 32bit registers). */
	TxAddr0 = 0x20,		/* Tx descriptors (also four 32bit). */
	RxBuf = 0x30,
	RxEarlyCnt = 0x34,
	RxEarlyStatus = 0x36,
	ChipCmd = 0x37,
	RxBufPtr = 0x38,
	RxBufAddr = 0x3A,
	IntrMask = 0x3C,
	IntrStatus = 0x3E,
	TxConfig = 0x40,
	ChipVersion = 0x43,
	RxConfig = 0x44,
	Timer = 0x48,		/* A general-purpose counter. */
	RxMissed = 0x4C,	/* 24 bits valid, write clears. */
	Cfg9346 = 0x50,
	Config0 = 0x51,
	Config1 = 0x52,
	FlashReg = 0x54,
	MediaStatus = 0x58,
	Config3 = 0x59,
	Config4 = 0x5A,		/* absent on RTL-8139A */
	HltClk = 0x5B,
	MultiIntr = 0x5C,
	TxSummary = 0x60,
	BasicModeCtrl = 0x62,
	BasicModeStatus = 0x64,
	NWayAdvert = 0x66,
	NWayLPAR = 0x68,
	NWayExpansion = 0x6A,
	/* Undocumented registers, but required for proper operation. */
	FIFOTMS = 0x70,		/* FIFO Control and test. */
	CSCR = 0x74,		/* Chip Status and Configuration Register. */
	PARA78 = 0x78,
	PARA7c = 0x7c,		/* Magic transceiver parameter register. */
	Config5 = 0xD8,		/* absent on RTL-8139A */
};

enum ClearBitMasks {
	MultiIntrClear = 0xF000,
	ChipCmdClear = 0xE2,
	Config1Clear = (1<<7)|(1<<6)|(1<<3)|(1<<2)|(1<<1),
};

enum ChipCmdBits {
	CmdReset = 0x10,
	CmdRxEnb = 0x08,
	CmdTxEnb = 0x04,
	RxBufEmpty = 0x01,
};

/* Interrupt register bits, using my own meaningful names. */
enum IntrStatusBits {
	PCIErr = 0x8000,
	PCSTimeout = 0x4000,
	RxFIFOOver = 0x40,
	RxUnderrun = 0x20,
	RxOverflow = 0x10,
	TxErr = 0x08,
	TxOK = 0x04,
	RxErr = 0x02,
	RxOK = 0x01,
};
enum TxStatusBits {
	TxHostOwns = 0x2000,
	TxUnderrun = 0x4000,
	TxStatOK = 0x8000,
	TxOutOfWindow = 0x20000000,
	TxAborted = 0x40000000,
	TxCarrierLost = 0x80000000,
};
enum RxStatusBits {
	RxMulticast = 0x8000,
	RxPhysical = 0x4000,
	RxBroadcast = 0x2000,
	RxBadSymbol = 0x0020,
	RxRunt = 0x0010,
	RxTooLong = 0x0008,
	RxCRCErr = 0x0004,
	RxBadAlign = 0x0002,
	RxStatusOK = 0x0001,
};

/* Bits in RxConfig. */
enum rx_mode_bits {
	AcceptErr = 0x20,
	AcceptRunt = 0x10,
	AcceptBroadcast = 0x08,
	AcceptMulticast = 0x04,
	AcceptMyPhys = 0x02,
	AcceptAllPhys = 0x01,
};

/* Bits in TxConfig. */
enum tx_config_bits {
	TxIFG1 = (1 << 25),	/* Interframe Gap Time */
	TxIFG0 = (1 << 24),	/* Enabling these bits violates IEEE 802.3 */
	TxLoopBack = (1 << 18) | (1 << 17), /* enable loopback test mode */
	TxCRC = (1 << 16),	/* DISABLE appending CRC to end of Tx packets */
	TxClearAbt = (1 << 0),	/* Clear abort (WO) */
	TxDMAShift = 8,		/* DMA burst value (0-7) is shift this many bits */

	TxVersionMask = 0x7C800000, /* mask out version bits 30-26, 23 */
};

/* Bits in Config1 */
enum Config1Bits {
	Cfg1_PM_Enable = 0x01,
	Cfg1_VPD_Enable = 0x02,
	Cfg1_PIO = 0x04,
	Cfg1_MMIO = 0x08,
	LWAKE = 0x10,		/* not on 8139, 8139A */
	Cfg1_Driver_Load = 0x20,
	Cfg1_LED0 = 0x40,
	Cfg1_LED1 = 0x80,
	SLEEP = (1 << 1),	/* only on 8139, 8139A */
	PWRDN = (1 << 0),	/* only on 8139, 8139A */
};

/* Bits in Config4 */
enum Config4Bits {
	LWPTN = (1 << 2),	/* not on 8139, 8139A */
};

enum RxConfigBits {
	/* Early Rx threshold, none or X/16 */
	RxCfgEarlyRxNone = 0,
	RxCfgEarlyRxShift = 24,

	/* rx fifo threshold */
	RxCfgFIFOShift = 13,
	//no rx threshold. The RTL8130 begins the transfer of data after
	//having received a whole packet in the FIFO.
	RxCfgFIFONone = (7 << RxCfgFIFOShift), 

	/* Max DMA burst */
	RxCfgDMAShift = 8,
	RxCfgDMAUnlimited = (7 << RxCfgDMAShift), //unlimited

	/* rx ring buffer length */
	RxCfgRcv8K = 0,
	RxCfgRcv16K = (1 << 11),
	RxCfgRcv32K = (1 << 12),
	RxCfgRcv64K = (1 << 11) | (1 << 12),

	/* Disable packet wrap at end of Rx buffer */
	RxNoWrap = (1 << 7),
};


/* Twister tuning parameters from RealTek.
   Completely undocumented, but required to tune bad links. */
enum CSCRBits {
	CSCR_LinkOKBit = 0x0400,
	CSCR_LinkChangeBit = 0x0800,
	CSCR_LinkStatusBits = 0x0f000,
	CSCR_LinkDownOffCmd = 0x003c0,
	CSCR_LinkDownCmd = 0x0f3c0,
};


enum Cfg9346Bits {
	Cfg9346_Lock = 0x00,
	Cfg9346_Unlock = 0xC0,
};


#define rtl8139_intr_mask \
	PCIErr | PCSTimeout | RxUnderrun | RxOverflow | RxFIFOOver | \
	TxErr | TxOK | RxErr | RxOK

#define RX_FIFO_THRESH	2	/* Rx buffer level before first PCI xfer.  */
#define RX_DMA_BURST	4	/* Maximum PCI burst, '6' is 1024 */
#define TX_DMA_BURST	4	/* Maximum PCI burst, '6' is 1024 */

#define rtl8139_rx_config \
	  RxCfgEarlyRxNone | RxCfgRcv16K | RxNoWrap |(AcceptMyPhys | AcceptBroadcast | AcceptMulticast) | \
	  (RX_FIFO_THRESH << RxCfgFIFOShift) | \
	  (RX_DMA_BURST << RxCfgDMAShift)	

#define RL_TXCFG_CONFIG	(TX_DMA_BURST << TxDMAShift)|TxIFG1|TxIFG0


/*
 * Under PCI, each device has 256 bytes of configuration address space,
 * of which the first 64 bytes are standardized as follows:
 */
#define PCI_VENDOR_ID		0x00	/* 16 bits */
#define PCI_DEVICE_ID		0x02	/* 16 bits */
#define PCI_COMMAND		0x04	/* 16 bits */
#define  PCI_COMMAND_IO		0x1	/* Enable response in I/O space */
#define  PCI_COMMAND_MEMORY	0x2	/* Enable response in Memory space */
#define  PCI_COMMAND_MASTER	0x4	/* Enable bus mastering */
#define  PCI_COMMAND_SPECIAL	0x8	/* Enable response to special cycles */
#define  PCI_COMMAND_INVALIDATE	0x10	/* Use memory write and invalidate */
#define  PCI_COMMAND_VGA_PALETTE 0x20	/* Enable palette snooping */
#define  PCI_COMMAND_PARITY	0x40	/* Enable parity checking */
#define  PCI_COMMAND_WAIT 	0x80	/* Enable address/data stepping */
#define  PCI_COMMAND_SERR	0x100	/* Enable SERR */
#define  PCI_COMMAND_FAST_BACK	0x200	/* Enable back-to-back writes */

#define PCI_STATUS		0x06	/* 16 bits */
#define  PCI_STATUS_CAP_LIST	0x10	/* Support Capability List */
#define  PCI_STATUS_66MHZ	0x20	/* Support 66 Mhz PCI 2.1 bus */
#define  PCI_STATUS_UDF		0x40	/* Support User Definable Features [obsolete] */
#define  PCI_STATUS_FAST_BACK	0x80	/* Accept fast-back to back */
#define  PCI_STATUS_PARITY	0x100	/* Detected parity error */
#define  PCI_STATUS_DEVSEL_MASK	0x600	/* DEVSEL timing */
#define  PCI_STATUS_DEVSEL_FAST	0x000	
#define  PCI_STATUS_DEVSEL_MEDIUM 0x200
#define  PCI_STATUS_DEVSEL_SLOW 0x400
#define  PCI_STATUS_SIG_TARGET_ABORT 0x800 /* Set on target abort */
#define  PCI_STATUS_REC_TARGET_ABORT 0x1000 /* Master ack of " */
#define  PCI_STATUS_REC_MASTER_ABORT 0x2000 /* Set on master abort */
#define  PCI_STATUS_SIG_SYSTEM_ERROR 0x4000 /* Set when we drive SERR */
#define  PCI_STATUS_DETECTED_PARITY 0x8000 /* Set on parity error */

#define PCI_CLASS_REVISION	0x08	/* High 24 bits are class, low 8
					   revision */
#define PCI_REVISION_ID         0x08    /* Revision ID */
#define PCI_CLASS_PROG          0x09    /* Reg. Level Programming Interface */
#define PCI_CLASS_DEVICE        0x0a    /* Device class */

#define PCI_CACHE_LINE_SIZE	0x0c	/* 8 bits */
#define PCI_LATENCY_TIMER	0x0d	/* 8 bits */
#define PCI_HEADER_TYPE		0x0e	/* 8 bits */
#define  PCI_HEADER_TYPE_NORMAL	0
#define  PCI_HEADER_TYPE_BRIDGE 1
#define  PCI_HEADER_TYPE_CARDBUS 2

#define PCI_BIST		0x0f	/* 8 bits */
#define PCI_BIST_CODE_MASK	0x0f	/* Return result */
#define PCI_BIST_START		0x40	/* 1 to start BIST, 2 secs or less */
#define PCI_BIST_CAPABLE	0x80	/* 1 if BIST capable */

/*
 * Base addresses specify locations in memory or I/O space.
 * Decoded size can be determined by writing a value of 
 * 0xffffffff to the register, and reading it back.  Only 
 * 1 bits are decoded.
 */
#define PCI_BASE_ADDRESS_0	0x10	/* 32 bits */
#define PCI_BASE_ADDRESS_1	0x14	/* 32 bits [htype 0,1 only] */
#define PCI_BASE_ADDRESS_2	0x18	/* 32 bits [htype 0 only] */
#define PCI_BASE_ADDRESS_3	0x1c	/* 32 bits */
#define PCI_BASE_ADDRESS_4	0x20	/* 32 bits */
#define PCI_BASE_ADDRESS_5	0x24	/* 32 bits */
#define  PCI_BASE_ADDRESS_SPACE	0x01	/* 0 = memory, 1 = I/O */
#define  PCI_BASE_ADDRESS_SPACE_IO 0x01
#define  PCI_BASE_ADDRESS_SPACE_MEMORY 0x00
#define  PCI_BASE_ADDRESS_MEM_TYPE_MASK 0x06
#define  PCI_BASE_ADDRESS_MEM_TYPE_32	0x00	/* 32 bit address */
#define  PCI_BASE_ADDRESS_MEM_TYPE_1M	0x02	/* Below 1M [obsolete] */
#define  PCI_BASE_ADDRESS_MEM_TYPE_64	0x04	/* 64 bit address */
#define  PCI_BASE_ADDRESS_MEM_PREFETCH	0x08	/* prefetchable? */
#define  PCI_BASE_ADDRESS_MEM_MASK	(~0x0fUL)
#define  PCI_BASE_ADDRESS_IO_MASK	(~0x03UL)
/* bit 1 is reserved if address_space = 1 */

/* Header type 0 (normal devices) */