config.help

是关于linux2.5.1的完全源码

CONFIG_MKISS
  KISS is a protocol used for the exchange of data between a computer
  and a Terminal Node Controller (a small embedded system commonly
  used for networking over AX.25 amateur radio connections; it
  connects the computer's serial port with the radio's microphone
  input and speaker output).

  Although KISS is less advanced than the 6pack protocol, it has
  the advantage that it is already supported by most modern TNCs
  without the need for a firmware upgrade.

  If you want to compile this driver as a module ( = code which can be
  inserted in and removed from the running kernel whenever you want),
  say M here and read <file:Documentation/modules.txt>.  The module
  will be called mkiss.o.

CONFIG_6PACK
  6pack is a transmission protocol for the data exchange between your
  PC and your TNC (the Terminal Node Controller acts as a kind of
  modem connecting your computer's serial port to your radio's
  microphone input and speaker output). This protocol can be used as
  an alternative to KISS for networking over AX.25 amateur radio
  connections, but it has some extended functionality.

  Note that this driver is still experimental and might cause
  problems. For details about the features and the usage of the
  driver, read <file:Documentation/networking/6pack.txt>.

  If you want to compile this driver as a module ( = code which can be
  inserted in and removed from the running kernel whenever you want),
  say M here and read <file:Documentation/modules.txt>.  The module
  will be called 6pack.o.

CONFIG_BPQETHER
  AX.25 is the protocol used for computer communication over amateur
  radio. If you say Y here, you will be able to send and receive AX.25
  traffic over Ethernet (also called "BPQ AX.25"), which could be
  useful if some other computer on your local network has a direct
  amateur radio connection.

CONFIG_DMASCC
  This is a driver for high-speed SCC boards, i.e. those supporting
  DMA on one port. You usually use those boards to connect your
  computer to an amateur radio modem (such as the WA4DSY 56kbps
  modem), in order to send and receive AX.25 packet radio network
  traffic.

  Currently, this driver supports Ottawa PI/PI2, Paccomm/Gracilis
  PackeTwin, and S5SCC/DMA boards. They are detected automatically.
  If you have one of these cards, say Y here and read the AX25-HOWTO,
  available from <http://www.linuxdoc.org/docs.html#howto>.

  This driver can operate multiple boards simultaneously. If you
  compile it as a module (by saying M instead of Y), it will be called
  dmascc.o. If you don't pass any parameter to the driver, all
  possible I/O addresses are probed. This could irritate other devices
  that are currently not in use. You may specify the list of addresses
  to be probed by "dmascc=addr1,addr2,..." (when compiled into the
  kernel image) or "io=addr1,addr2,..." (when loaded as a module). The
  network interfaces will be called dmascc0 and dmascc1 for the board
  detected first, dmascc2 and dmascc3 for the second one, and so on.

  Before you configure each interface with ifconfig, you MUST set
  certain parameters, such as channel access timing, clock mode, and
  DMA channel. This is accomplished with a small utility program,
  dmascc_cfg, available at
  <http://www.nt.tuwien.ac.at/~kkudielk/Linux/>. Please be sure to get
  at least version 1.27 of dmascc_cfg, as older versions will not
  work with the current driver.

CONFIG_SCC
  These cards are used to connect your Linux box to an amateur radio
  in order to communicate with other computers. If you want to use
  this, read <file:Documentation/networking/z8530drv.txt> and the
  AX25-HOWTO, available from
  <http://www.linuxdoc.org/docs.html#howto>. Also make sure to say Y
  to "Amateur Radio AX.25 Level 2" support.

  If you want to compile this as a module ( = code which can be
  inserted in and removed from the running kernel whenever you want),
  say M here and read <file:Documentation/modules.txt>.  The module
  will be called scc.o.

CONFIG_SCC_TRXECHO
  Some transmitters feed the transmitted signal back to the receive
  line.  Say Y here to foil this by explicitly disabling the receiver
  during data transmission.  If in doubt, say Y.

CONFIG_SCC_DELAY
  Say Y here if you experience problems with the SCC driver not
  working properly; please read
  <file:Documentation/networking/z8530drv.txt> for details. If unsure,
  say N.

CONFIG_YAM
  The YAM is a modem for packet radio which connects to the serial
  port and includes some of the functions of a Terminal Node
  Controller. If you have one of those, say Y here.

  If you want to compile this as a module ( = code which can be
  inserted in and removed from the running kernel whenever you want),
  say M here and read <file:Documentation/modules.txt>.

CONFIG_BAYCOM_PAR
  This is a driver for Baycom style simple amateur radio modems that
  connect to a parallel interface. The driver supports the picpar and
  par96 designs. To configure the driver, use the sethdlc utility
  available in the standard ax25 utilities package. For information on
  the modems, see <http://www.baycom.de/> and the file
  <file:Documentation/networking/baycom.txt>.

  If you want to compile this driver as a module ( = code which can be
  inserted in and removed from the running kernel whenever you want),
  say M here and read <file:Documentation/modules.txt>.  This is
  recommended.  The module will be called baycom_par.o.

CONFIG_BAYCOM_EPP
  This is a driver for Baycom style simple amateur radio modems that
  connect to a parallel interface. The driver supports the EPP
  designs. To configure the driver, use the sethdlc utility available
  in the standard ax25 utilities package. For information on the
  modems, see <http://www.baycom.de/> and the file
  <file:Documentation/networking/baycom.txt>.

  If you want to compile this driver as a module ( = code which can be
  inserted in and removed from the running kernel whenever you want),
  say M here and read <file:Documentation/modules.txt>.  This is
  recommended.  The module will be called baycom_par.o.

CONFIG_BAYCOM_SER_FDX
  This is one of two drivers for Baycom style simple amateur radio
  modems that connect to a serial interface. The driver supports the
  ser12 design in full-duplex mode. In addition, it allows the
  baudrate to be set between 300 and 4800 baud (however not all modems
  support all baudrates). This is the preferred driver. The next
  driver, "BAYCOM ser12 half-duplex driver for AX.25" is the old
  driver and still provided in case this driver does not work with
  your serial interface chip. To configure the driver, use the sethdlc
  utility available in the standard ax25 utilities package. For
  information on the modems, see <http://www.baycom.de/> and
  <file:Documentation/networking/baycom.txt>.

  If you want to compile this driver as a module ( = code which can be
  inserted in and removed from the running kernel whenever you want),
  say M here and read <file:Documentation/modules.txt>.  This is
  recommended.  The module will be called baycom_ser_fdx.o.

CONFIG_BAYCOM_SER_HDX
  This is one of two drivers for Baycom style simple amateur radio
  modems that connect to a serial interface. The driver supports the
  ser12 design in full-duplex mode. This is the old driver.  It is
  still provided in case your serial interface chip does not work with
  the full-duplex driver. This driver is depreciated.  To configure
  the driver, use the sethdlc utility available in the standard ax25
  utilities package. For information on the modems, see
  <http://www.baycom.de/> and
  <file:Documentation/networking/baycom.txt>.

  If you want to compile this driver as a module ( = code which can be
  inserted in and removed from the running kernel whenever you want),
  say M here and read <file:Documentation/modules.txt>.  This is
  recommended.  The module will be called baycom_ser_hdx.o.

CONFIG_SOUNDMODEM
  This experimental driver allows a standard Sound Blaster or
  WindowsSoundSystem compatible sound card to be used as a packet
  radio modem (NOT as a telephone modem!), to send digital traffic
  over amateur radio.

  To configure the driver, use the sethdlc, smdiag and smmixer
  utilities available in the standard ax25 utilities package. For
  information on how to key the transmitter, see
  <http://www.ife.ee.ethz.ch/~sailer/pcf/ptt_circ/ptt.html> and
  <file:Documentation/networking/soundmodem.txt>.

  If you want to compile this driver as a module ( = code which can be
  inserted in and removed from the running kernel whenever you want),
  say M here and read <file:Documentation/modules.txt>.  This is
  recommended.  The module will be called soundmodem.o.

CONFIG_SOUNDMODEM_SBC
  This option enables the soundmodem driver to use Sound Blaster and
  compatible cards. If you have a dual mode card (i.e. a WSS cards
  with a Sound Blaster emulation) you should say N here and Y to
  "Sound card modem support for WSS and Crystal cards", below, because
  this usually results in better performance. This option also
  supports SB16/32/64 in full-duplex mode.

CONFIG_SOUNDMODEM_WSS
  This option enables the soundmodem driver to use WindowsSoundSystem
  compatible cards. These cards feature a codec chip from either
  Analog Devices (such as AD1848, AD1845, AD1812) or Crystal
  Semiconductors (such as CS4248, CS423x). This option also supports
  the WSS full-duplex operation which currently works with Crystal
  CS423x chips. If you don't need full-duplex operation, do not enable
  it to save performance.

CONFIG_SOUNDMODEM_AFSK1200
  This option enables the soundmodem driver 1200 baud AFSK modem,
  compatible to popular modems using TCM3105 or AM7911. The
  demodulator requires about 12% of the CPU power of a Pentium 75 CPU
  per channel.

CONFIG_SOUNDMODEM_AFSK2400_7
  This option enables the soundmodem driver 2400 baud AFSK modem,
  compatible to TCM3105 modems (over-)clocked with a 7.3728MHz
  crystal. Note that the availability of this driver does _not_ imply
  that I recommend building such links. It is only here since users
  especially in eastern Europe have asked me to do so. In fact this
  modulation scheme has many disadvantages, mainly its incompatibility
  with many transceiver designs and the fact that the TCM3105 (if
  used) is operated widely outside its specifications.

CONFIG_SOUNDMODEM_AFSK2400_8
  This option enables the soundmodem driver 2400 baud AFSK modem,
  compatible to TCM3105 modems (over-)clocked with an 8MHz crystal.
  Note that the availability of this driver does _not_ imply that I
  recommend building such links. It is only here since users
  especially in eastern Europe have asked me to do so. In fact this
  modulation scheme has many disadvantages, mainly its incompatibility
  with many transceiver designs and the fact that the TCM3105 (if
  used) is operated widely outside its specifications.

CONFIG_SOUNDMODEM_AFSK2666
  This option enables the soundmodem driver 2666 baud AFSK modem.
  This modem is experimental, and not compatible to anything
  else I know of.

CONFIG_SOUNDMODEM_PSK4800
  This option enables the soundmodem driver 4800 baud 8PSK modem.
  This modem is experimental, and not compatible to anything
  else I know of.

CONFIG_SOUNDMODEM_HAPN4800
  This option enables the soundmodem driver 4800 baud HAPN-1
  compatible modem. This modulation seems to be widely used 'down
  under' and in the Netherlands. Here, nobody uses it, so I could not
  test if it works. It is compatible to itself, however :-)

CONFIG_SOUNDMODEM_FSK9600
  This option enables the soundmodem driver 9600 baud FSK modem,
  compatible to the G3RUH standard. The demodulator requires about 4%
  of the CPU power of a Pentium 75 CPU per channel. You can say Y to
  both 1200 baud AFSK and 9600 baud FSK if you want (but obviously you
  can only use one protocol at a time, depending on what the other end
  can understand).