config.help

是关于linux2.5.1的完全源码

    - API support for protocols like HDLC (LAPB),
      HDLC Streaming, X.25, Frame Relay and BiSync.

    - Ethernet Bridging over Frame Relay protocol.

    - MULTILINK PPP

    - Async PPP (Modem Dialup)

  If you have one or more of these cards, say M to this option; you
  may then also want to read the file
  <file:Documentation/networking/wanpipe.txt>.  The next questions
  will ask you about the protocols you want the driver to support.

  The driver will be compiled as a module ( = code which can be
  inserted in and removed from the running kernel whenever you want).
  The module will be called wanpipe.o.  For general information about
  modules read <file:Documentation/modules.txt>.

CONFIG_WANPIPE_X25
  Say Y to this option if you are planning to connect a WANPIPE card
  to an X.25 network.  Note, this feature also includes the X.25 API
  support used to develope custom applications over the X.25 protocol.
  If you say N, the X.25 support will not be included in the driver.
  The X.25 option is supported on S514-PCI and S508-ISA cards.

CONFIG_WANPIPE_FR
  Say Y to this option if you are planning to connect a WANPIPE card
  to a frame relay network, or use frame relay API to develope
  custom applications over the Frame  Relay protocol.
  This feature also contains the Ethernet Bridging over Frame Relay,
  where a WANPIPE frame relay link can be directly connected to the
  Linux kernel bridge.  If you say N, the frame relay support will
  not be included in the driver. The Frame Relay option is
  supported on S514-PCI and S508-ISA cards.

CONFIG_WANPIPE_PPP
  Say Y to this option if you are planning to connect a WANPIPE card
  to a leased line using Point-to-Point protocol (PPP). If you say N,
  the PPP support will not be included in the driver. The PPP option
  is supported on S514-PCI/S508-ISA cards.

CONFIG_WANPIPE_MULTPPP
  Say Y to this option if you are planning to connect a WANPIPE card
  to a leased line using Point-to-Point protocol (PPP).  Note, the
  MultiPort PPP uses the Linux Kernel SyncPPP protocol over the
  Sangoma HDLC Streaming adapter.  In this case each Sangoma adapter
  port can support an independent PPP connection.  For example, a
  single Quad-Port PCI adapter can support up to four independent
  PPP links. If you say N,the PPP support will not be included in the
  driver.  The PPP option is supported on S514-PCI/S508-ISA cards.

CONFIG_WANPIPE_CHDLC
  Say Y to this option if you are planning to connect a WANPIPE card
  to a leased line using the Cisco HDLC protocol. This now supports
  Dual Port Cisco HDLC on the S514-PCI/S508-ISA cards.
  This support also allows user to build applications using the
  HDLC streaming API.

  CHDLC Streaming driver also supports MULTILINK PPP
  support that can bind multiple WANPIPE T1 cards into
  a single logical channel.

  If you say  N, the Cisco HDLC support and
  HDLC streaming API and MULTILINK PPP will not be
  included in the driver.

CONFIG_COMX
  Say Y if you want to use any board from the MultiGate (COMX) family.
  These boards are synchronous serial adapters for the PC,
  manufactured by ITConsult-Pro Co, Hungary.

  Read <file:Documentation/networking/comx.txt> for help on
  configuring and using COMX interfaces.  Further info on these cards
  can be found at <http://www.itc.hu/> or <[e-mail]>.

  You must say Y to "/proc file system support" (CONFIG_PROC_FS) to
  use this driver.

  If you want to compile this as a module, say M and read
  <file:Documentation/modules.txt>.  The module will be called comx.o.

CONFIG_COMX_HW_COMX
  Hardware driver for the 'CMX', 'COMX' and 'HiCOMX' boards from the
  MultiGate family. Say Y if you have one of these.

  You will need additional firmware to use these cards, which are
  downloadable from <ftp://ftp.itc.hu/>.

  If you want to compile this as a module, say M and read
  <file:Documentation/modules.txt>.  The module will be called
  comx-hw-comx.o.

CONFIG_COMX_HW_LOCOMX
  Hardware driver for the 'LoCOMX' board from the MultiGate family.
  Say Y if you have a board like this.

  If you want to compile this as a module, say M and read
  <file:Documentation/modules.txt>.  The module will be called
  comx-hw-locomx.o.

CONFIG_COMX_HW_MIXCOM
  Hardware driver for the 'MixCOM' board from the MultiGate family.
  Say Y if you have a board like this.

  If you want to use the watchdog device on this card, you should
  select it in the Watchdog Cards section of the Character Devices
  configuration. The ISDN interface of this card is Teles 16.3
  compatible, you should enable it in the ISDN configuration menu. The
  driver for the flash ROM of this card is available separately on
  <ftp://ftp.itc.hu/>.

  If you want to compile this as a module, say M and read
  <file:Documentation/modules.txt>. The module will be called
  comx-hw-mixcom.o.

CONFIG_COMX_PROTO_PPP
  Cisco-HDLC and synchronous PPP protocol driver for all MultiGate
  boards. Say Y if you want to use either protocol on your MultiGate
  boards.

  If you want to compile this as a module, say M and read
  <file:Documentation/modules.txt>.  The module will be called
  comx-proto-ppp.o.

CONFIG_COMX_PROTO_LAPB
  LAPB protocol driver for all MultiGate boards. Say Y if you
  want to use this protocol on your MultiGate boards.

  If you want to compile this as a module, say M and read
  <file:Documentation/modules.txt>.  The module will be called
  comx-proto-lapb.o.

CONFIG_COMX_PROTO_FR
  Frame Relay protocol driver for all MultiGate boards. Say Y if you
  want to use this protocol on your MultiGate boards.

  If you want to compile this as a module, say M and read
  <file:Documentation/modules.txt>.  The module will be called
  comx-proto-fr.o.

CONFIG_CYCLADES_SYNC
  Cyclom 2X from Cyclades Corporation (<http://www.cyclades.com/> and
  <http://www.cyclades.com.br/>) is an intelligent multiprotocol WAN
  adapter with data transfer rates up to 512 Kbps. These cards support
  the X.25 and SNA related protocols. If you have one or more of these
  cards, say Y to this option. The next questions will ask you about
  the protocols you want the driver to support (for now only X.25 is
  supported).

  While no documentation is available at this time please grab the
  wanconfig tarball in
  <http://www.conectiva.com.br/~acme/cycsyn-devel/> (with minor changes
  to make it compile with the current wanrouter include files; efforts
  are being made to use the original package available at
  <ftp://ftp.sangoma.com/>).

  Feel free to contact me or the cycsyn-devel mailing list at
  [e-mail] and [e-mail] for
  additional details, I hope to have documentation available as soon
  as possible. (Cyclades Brazil is writing the Documentation).

  The driver will be compiled as a module ( = code which can be
  inserted in and removed from the running kernel whenever you want).
  The module will be called cyclomx.o. For general information about
  modules read <file:Documentation/modules.txt>.

CONFIG_CYCLOMX_X25
  Say Y to this option if you are planning to connect a Cyclom 2X card
  to an X.25 network.

  If you say N, the X.25 support will not be included in the driver
  (saves about 11 KB of kernel memory).

CONFIG_HDLC
  Say Y to this option if your Linux box contains a WAN card supported
  by this driver and you are planning to connect the box to a WAN
  ( = Wide Area Network). You will need supporting software from
  <http://hq.pm.waw.pl/hdlc/>.
  Generic HDLC driver currently supports raw HDLC, Cisco HDLC, Frame
  Relay, synchronous Point-to-Point Protocol (PPP) and X.25.

  If unsure, say N here.

CONFIG_HDLC_PPP
  Say Y to this option if you want generic HDLC driver to support
  PPP over WAN (Wide Area Network) connections.

  If unsure, say N here.

CONFIG_HDLC_X25
  Say Y to this option if you want generic HDLC driver to support
  X.25 protocol over WAN (Wide Area Network) connections.

  If unsure, say N here.

CONFIG_N2
  This driver is for RISCom/N2 single or dual channel ISA cards
  made by SDL Communications Inc.  If you have such a card,
  say Y here and see <http://hq.pm.waw.pl/pub/hdlc/>.

  Note that N2csu and N2dds cards are not supported by this driver.

  If unsure, say N here.

CONFIG_C101
  This driver is for C101 SuperSync ISA cards made by Moxa
  Technologies Co., Ltd. If you have such a card,
  say Y here and see <http://hq.pm.waw.pl/pub/hdlc/>

  If unsure, say N here.