keyspan.c

是关于linux2.5.1的完全源码

{
	int 				response;
	const struct ezusb_hex_record 	*record;
	char				*fw_name;

	dbg("Keyspan startup version %04x product %04x",
	    serial->dev->descriptor.bcdDevice,
	    serial->dev->descriptor.idProduct); 
	
	if ((serial->dev->descriptor.bcdDevice & 0x8000) != 0x8000) {
		dbg("Firmware already loaded.  Quitting.");
		return(1);
	}

		/* Select firmware image on the basis of idProduct */
	switch (serial->dev->descriptor.idProduct) {
	case keyspan_usa28_pre_product_id:
		record = &keyspan_usa28_firmware[0];
		fw_name = "USA28";
		break;

	case keyspan_usa28x_pre_product_id:
		record = &keyspan_usa28x_firmware[0];
		fw_name = "USA28X";
		break;

	case keyspan_usa28xa_pre_product_id:
		record = &keyspan_usa28xa_firmware[0];
		fw_name = "USA28XA";
		break;

	case keyspan_usa28xb_pre_product_id:
		record = &keyspan_usa28xb_firmware[0];
		fw_name = "USA28XB";
		break;

	case keyspan_usa19_pre_product_id:
		record = &keyspan_usa19_firmware[0];
		fw_name = "USA19";
		break;
			     
	case keyspan_usa19qi_pre_product_id:
		record = &keyspan_usa19qi_firmware[0];
		fw_name = "USA19QI";
		break;
			     
	case keyspan_usa19qw_pre_product_id:
		record = &keyspan_usa19qw_firmware[0];
		fw_name = "USA19QI";
		break;
			     
	case keyspan_usa18x_pre_product_id:
		record = &keyspan_usa18x_firmware[0];
		fw_name = "USA18X";
		break;
			     
	case keyspan_usa19w_pre_product_id:
		record = &keyspan_usa19w_firmware[0];
		fw_name = "USA19W";
		break;
		
	case keyspan_usa49w_pre_product_id:
		record = &keyspan_usa49w_firmware[0];
		fw_name = "USA49W";
		break;

	default:
		record = NULL;
		fw_name = "Unknown";
		break;
	}

	if (record == NULL) {
		err("Required keyspan firmware image (%s) unavailable.", fw_name);
		return(1);
	}

	dbg("Uploading Keyspan %s firmware.", fw_name);

		/* download the firmware image */
	response = ezusb_set_reset(serial, 1);

	while(record->address != 0xffff) {
		response = ezusb_writememory(serial, record->address,
					     (unsigned char *)record->data,
					     record->data_size, 0xa0);
		if (response < 0) {
			err("ezusb_writememory failed for Keyspan"
			    "firmware (%d %04X %p %d)",
			    response, 
			    record->address, record->data, record->data_size);
			break;
		}
		record++;
	}
		/* bring device out of reset. Renumeration will occur in a
		   moment and the new device will bind to the real driver */
	response = ezusb_set_reset(serial, 0);

	/* we don't want this device to have a driver assigned to it. */
	return (1);
}

/* Helper functions used by keyspan_setup_urbs */
static struct urb *keyspan_setup_urb (struct usb_serial *serial, int endpoint,
				      int dir, void *ctx, char *buf, int len,
				      void (*callback)(struct urb *))
{
	struct urb *urb;

	if (endpoint == -1)
		return NULL;		/* endpoint not needed */

	dbg ("%s - alloc for endpoint %d.", __FUNCTION__, endpoint);
	urb = usb_alloc_urb(0, GFP_KERNEL);		/* No ISO */
	if (urb == NULL) {
		dbg ("%s - alloc for endpoint %d failed.", __FUNCTION__, endpoint);
		return NULL;
	}

		/* Fill URB using supplied data. */
	FILL_BULK_URB(urb, serial->dev,
		      usb_sndbulkpipe(serial->dev, endpoint) | dir,
		      buf, len, callback, ctx);

	return urb;
}

static struct callbacks {
	void	(*instat_callback)(struct urb *);
	void	(*glocont_callback)(struct urb *);
	void	(*indat_callback)(struct urb *);
	void	(*outdat_callback)(struct urb *);
	void	(*inack_callback)(struct urb *);
	void	(*outcont_callback)(struct urb *);
} keyspan_callbacks[] = {
	{
		/* msg_usa26 callbacks */
		instat_callback:	usa26_instat_callback,
		glocont_callback:	usa26_glocont_callback,
		indat_callback:		usa26_indat_callback,
		outdat_callback:	usa2x_outdat_callback,
		inack_callback:		usa26_inack_callback,
		outcont_callback:	usa26_outcont_callback,
	}, {
		/* msg_usa28 callbacks */
		instat_callback:	usa28_instat_callback,
		glocont_callback:	usa28_glocont_callback,
		indat_callback:		usa28_indat_callback,
		outdat_callback:	usa2x_outdat_callback,
		inack_callback:		usa28_inack_callback,
		outcont_callback:	usa28_outcont_callback,
	}, {
		/* msg_usa49 callbacks */
		instat_callback:	usa49_instat_callback,
		glocont_callback:	usa49_glocont_callback,
		indat_callback:		usa49_indat_callback,
		outdat_callback:	usa2x_outdat_callback,
		inack_callback:		usa49_inack_callback,
		outcont_callback:	usa49_outcont_callback,
	}
};

	/* Generic setup urbs function that uses
	   data in device_details */
static void keyspan_setup_urbs(struct usb_serial *serial)
{
	int				i, j;
	struct keyspan_serial_private 	*s_priv;
	const struct keyspan_device_details	*d_details;
	struct usb_serial_port		*port;
	struct keyspan_port_private	*p_priv;
	struct callbacks		*cback;
	int				endp;

	dbg ("%s", __FUNCTION__);

	s_priv = (struct keyspan_serial_private *)(serial->private);
	d_details = s_priv->device_details;

		/* Setup values for the various callback routines */
	cback = &keyspan_callbacks[d_details->msg_format];

		/* Allocate and set up urbs for each one that is in use, 
		   starting with instat endpoints */
	s_priv->instat_urb = keyspan_setup_urb
		(serial, d_details->instat_endpoint, USB_DIR_IN,
		 serial, s_priv->instat_buf, INSTAT_BUFLEN,
		 cback->instat_callback);

	s_priv->glocont_urb = keyspan_setup_urb
		(serial, d_details->glocont_endpoint, USB_DIR_OUT,
		 serial, s_priv->glocont_buf, GLOCONT_BUFLEN,
		 cback->glocont_callback);

		/* Setup endpoints for each port specific thing */
	for (i = 0; i < d_details->num_ports; i ++) {
		port = &serial->port[i];
		p_priv = (struct keyspan_port_private *)(port->private);

		/* Do indat endpoints first, once for each flip */
		endp = d_details->indat_endpoints[i];
		for (j = 0; j <= d_details->indat_endp_flip; ++j, ++endp) {
			p_priv->in_urbs[j] = keyspan_setup_urb
				(serial, endp, USB_DIR_IN, port,
				 p_priv->in_buffer[j], 64,
				 cback->indat_callback);
		}
		for (; j < 2; ++j)
			p_priv->in_urbs[j] = NULL;

		/* outdat endpoints also have flip */
		endp = d_details->outdat_endpoints[i];
		for (j = 0; j <= d_details->outdat_endp_flip; ++j, ++endp) {
			p_priv->out_urbs[j] = keyspan_setup_urb
				(serial, endp, USB_DIR_OUT, port,
				 p_priv->out_buffer[j], 64,
				 cback->outdat_callback);
		}
		for (; j < 2; ++j)
			p_priv->out_urbs[j] = NULL;

		/* inack endpoint */
		p_priv->inack_urb = keyspan_setup_urb
			(serial, d_details->inack_endpoints[i], USB_DIR_IN,
			 port, p_priv->inack_buffer, 1, cback->inack_callback);

		/* outcont endpoint */
		p_priv->outcont_urb = keyspan_setup_urb
			(serial, d_details->outcont_endpoints[i], USB_DIR_OUT,
			 port, p_priv->outcont_buffer, 64,
			 cback->outcont_callback);
	}	

}

/* usa19 function doesn't require prescaler */
static int keyspan_usa19_calc_baud(u32 baud_rate, u32 baudclk, u8 *rate_hi,
				   u8 *rate_low, u8 *prescaler, int portnum)
{
	u32 	b16,	/* baud rate times 16 (actual rate used internally) */
		div,	/* divisor */	
		cnt;	/* inverse of divisor (programmed into 8051) */
		
	dbg ("%s - %d.", __FUNCTION__, baud_rate);

		/* prevent divide by zero...  */
	if( (b16 = (baud_rate * 16L)) == 0) {
		return (KEYSPAN_INVALID_BAUD_RATE);
	}

		/* Any "standard" rate over 57k6 is marginal on the USA-19
		   as we run out of divisor resolution. */
	if (baud_rate > 57600) {
		return (KEYSPAN_INVALID_BAUD_RATE);
	}

		/* calculate the divisor and the counter (its inverse) */
	if( (div = (baudclk / b16)) == 0) {
		return (KEYSPAN_INVALID_BAUD_RATE);
	}
	else {
		cnt = 0 - div;
	}

	if(div > 0xffff) {
		return (KEYSPAN_INVALID_BAUD_RATE);
	}

		/* return the counter values if non-null */
	if (rate_low) {
		*rate_low = (u8) (cnt & 0xff);
	}
	if (rate_hi) {
		*rate_hi = (u8) ((cnt >> 8) & 0xff);
	}
	if (rate_low && rate_hi) {
		dbg ("%s - %d %02x %02x.", __FUNCTION__, baud_rate, *rate_hi, *rate_low);
	}
	
	return (KEYSPAN_BAUD_RATE_OK);
}

static int keyspan_usa19w_calc_baud(u32 baud_rate, u32 baudclk, u8 *rate_hi,
				    u8 *rate_low, u8 *prescaler, int portnum)
{
	u32 	b16,	/* baud rate times 16 (actual rate used internally) */
		clk,	/* clock with 13/8 prescaler */
		div,	/* divisor using 13/8 prescaler */	
		res,	/* resulting baud rate using 13/8 prescaler */
		diff,	/* error using 13/8 prescaler */
		smallest_diff;
	u8	best_prescaler;
	int	i;

	dbg ("%s - %d.", __FUNCTION__, baud_rate);

		/* prevent divide by zero */
	if( (b16 = baud_rate * 16L) == 0) {
		return (KEYSPAN_INVALID_BAUD_RATE);
	}

		/* Calculate prescaler by trying them all and looking
		   for best fit */
		
		/* start with largest possible difference */
	smallest_diff = 0xffffffff;

		/* 0 is an invalid prescaler, used as a flag */
	best_prescaler = 0;

	for(i = 8; i <= 0xff; ++i) {
		clk = (baudclk * 8) / (u32) i;
		
		if( (div = clk / b16) == 0) {
			continue;
		}

		res = clk / div;
		diff= (res > b16) ? (res-b16) : (b16-res);

		if(diff < smallest_diff) {
			best_prescaler = i;
			smallest_diff = diff;
		}
	}

	if(best_prescaler == 0) {
		return (KEYSPAN_INVALID_BAUD_RATE);
	}

	clk = (baudclk * 8) / (u32) best_prescaler;
	div = clk / b16;

		/* return the divisor and prescaler if non-null */
	if (rate_low) {
		*rate_low = (u8) (div & 0xff);
	}
	if (rate_hi) {
		*rate_hi = (u8) ((div >> 8) & 0xff);
	}
	if (prescaler) {
		*prescaler = best_prescaler;
		/*  dbg("%s - %d %d", __FUNCTION__, *prescaler, div); */
	}
	return (KEYSPAN_BAUD_RATE_OK);
}

	/* USA-28 supports different maximum baud rates on each port */
static int keyspan_usa28_calc_baud(u32 baud_rate, u32 baudclk, u8 *rate_hi,
				    u8 *rate_low, u8 *prescaler, int portnum)
{
	u32 	b16,	/* baud rate times 16 (actual rate used internally) */
		div,	/* divisor */	
		cnt;	/* inverse of divisor (programmed into 8051) */

	dbg ("%s - %d.", __FUNCTION__, baud_rate);

		/* prevent divide by zero */
	if ((b16 = baud_rate * 16L) == 0)
		return (KEYSPAN_INVALID_BAUD_RATE);

		/* calculate the divisor and the counter (its inverse) */
	if ((div = (KEYSPAN_USA28_BAUDCLK / b16)) == 0) {
		return (KEYSPAN_INVALID_BAUD_RATE);
	}
	else {
		cnt = 0 - div;
	}

		/* check for out of range, based on portnum, 
		   and return result */
	if(portnum == 0) {
		if(div > 0xffff)
			return (KEYSPAN_INVALID_BAUD_RATE);
	}
	else {
		if(portnum == 1) {
			if(div > 0xff) {
				return (KEYSPAN_INVALID_BAUD_RATE);
			}
		}
		else {
			return (KEYSPAN_INVALID_BAUD_RATE);
		}
	}

		/* return the counter values if not NULL
		   (port 1 will ignore retHi) */
	if (rate_low) {
		*rate_low = (u8) (cnt & 0xff);
	}
	if (rate_hi) {
		*rate_hi = (u8) ((cnt >> 8) & 0xff);
	}
	dbg ("%s - %d OK.", __FUNCTION__, baud_rate);
	return (KEYSPAN_BAUD_RATE_OK);
}



static int keyspan_usa26_send_setup(struct usb_serial *serial,
				    struct usb_serial_port *port,
				    int reset_port)
{
	struct keyspan_usa26_portControlMessage	msg;		
	struct keyspan_serial_private 		*s_priv;
	struct keyspan_port_private 		*p_priv;
	const struct keyspan_device_details	*d_details;
	int 					outcont_urb;
	struct urb				*this_urb;
	int 					device_port, err;

	dbg ("%s reset=%d", __FUNCTION__, reset_port); 

	s_priv = (struct keyspan_serial_private *)(serial->private);
	p_priv = (struct keyspan_port_private *)(port->private);
	d_details = s_priv->device_details;
	device_port = port->number - port->serial->minor;

	outcont_urb = d_details->outcont_endpoints[port->number];
	this_urb = p_priv->outcont_urb;

	dbg("%s - endpoint %d", __FUNCTION__, usb_pipeendpoint(this_urb->pipe));

		/* Make sure we have an urb then send the message */
	if (this_urb == NULL) {
		dbg("%s - oops no urb.", __FUNCTION__);
		return -1;
	}

	p_priv->resend_cont = 1;
	if (this_urb->status == -EINPROGRESS) {
		/*  dbg ("%s - already writing", __FUNCTION__); */
		return(-1);
	}

	memset(&msg, 0, sizeof (struct keyspan_usa26_portControlMessage));
	
		/* Only set baud rate if it's changed */	
	if (p_priv->old_baud != p_priv->baud) {
		p_priv->old_baud = p_priv->baud;
		msg.setClocking = 0xff;
		if (d_details->calculate_baud_rate
		    (p_priv->baud, d_details->baudclk, &msg.baudHi,
		     &msg.baudLo, &msg.prescaler, device_port) == KEYSPAN_INVALID_BAUD_RATE ) {
			dbg("%s - Invalid baud rate %d requested, using 9600.", __FUNCTION__,
			    p_priv->baud);
			msg.baudLo = 0;
			msg.baudHi = 125;	/* Values for 9600 baud */
			msg.prescaler = 10;
		}
		msg.setPrescaler = 0xff;
	}

	msg.lcr = (p_priv->cflag & CSTOPB)? STOPBITS_678_2: STOPBITS_5678_1;
	switch (p_priv->cflag & CSIZE) {
	case CS5:
		msg.lcr |= USA_DATABITS_5;
		break;
	case CS6:
		msg.lcr |= USA_DATABITS_6;
		break;
	case CS7:
		msg.lcr |= USA_DATABITS_7;
		break;
	case CS8:
		msg.lcr |= USA_DATABITS_8;