📄 main.c
字号:
#include "c8051f320.h"
#include "typedef.h"
#include "misc.h"
#include "io.h"
//#include "reg51.H"
#include "api.h"
#define uchar unsigned char
#define uint unsigned int
void init_io(); //声明外部函数
void RX_Mode();
void init_int0();
void CheckButtons();
uchar SPI_RW_REG(BYTE reg,BYTE value);
//extern uchar SPI_RW_REG123(BYTE reg,BYTE value);
uchar flag;
#define uchar unsigned char
#define TX_ADR_WIDTH 5 // 5 bytes TX(RX) address width
#define TX_PLOAD_WIDTH 20 // 20 bytes TX payload
uchar const TX_ADDRESS[TX_ADR_WIDTH] = {0x34,0x43,0x10,0x10,0x01}; // Define a static TX address
/*uchar Original_ADDRESS[TX_ADR_WIDTH] ={0x32,0x41,0x08,0x08,0x00}; //Define Original address
uchar OnePress_ADDRESS[TX_ADR_WIDTH] ={0x33,0x42,0x09,0x09,0x02};
/*BYTE const TX_PAYLOAD[TX_PLOAD_WIDTH] = {0x00,0x01,0x02,0x03,0x04,0x05,0x06,0x07,
0x08,0x09,0x0a,0x0b,0x0c,0x0d,0x0e,0x0f}; */
uchar rx_buf[TX_PLOAD_WIDTH];
uchar tx_buf[TX_PLOAD_WIDTH];
sbit key=P3^0;
sbit led=P2^4;
/**************************************************/
sbit CE = P0^4;
sbit CSN= P0^3;
sbit SCK= P0^0;
sbit MOSI= P0^2;
sbit MISO= P0^1;
sbit IRQ = P0^5;
/**************************************************/
uchar bdata sta;
sbit RX_DR =sta^6;
sbit TX_DS =sta^5;
sbit MAX_RT =sta^4;
uchar tf=0; // Send interrut enabled flag
uchar t; //record the number of times you press the button
uchar i; //recond the number of times led shake
/*void main(void) // 主程序
{
bit light; //位变量
uint n;
PCA0MD &= 0xb9;
while(1) //程序循环
{
if(!K1) //如果读到K1为0
{
for(n=0;n<1000;n++); //等待按键稳定
light=~light; //每按键一次，标记变化一次
while(!K1); //等待按键松开
for(n=0;n<1000;n++); //等待按键稳定松开
}
P0=light; //直接把位变量赋值给LED灯
}
}
*/
void delays(uchar n)
{
for(;n>0;n--)
_nop_();
}
void init_io(void)
{
delays(100);
CE=0; // chip enable
CSN=1; // Spi disable
SCK=0; // Spi clock line init high
}
void init_int0()
{
EA=1;
EX0=1; // Enable int0 interrupt.
}
/*The following program is achieve by HardWare SPI*/
void SPI_rf_write(uchar dat)
{
while(SPI0CFG&0x80);
SPIF = 0;
SPI0DAT = dat;
while(!SPIF); //wait spi transfer finish
}
uchar SPI_rf_read(void)
{
while(SPI0CFG&0x80);
SPIF = 0;
SPI0DAT = 0x00;
while(!SPIF); //wait spi transfer finish
return (SPI0DAT);
}
void write_rf_reg(uchar address,uchar dat)
{
CSN=0;
SPI_rf_write(address);
SPI_rf_write(dat);
CSN=1;
}
uchar read_rf_reg(uchar address)
{
uchar status;
CSN=0;
SPI_rf_write(address);
status = SPI_rf_read();
CSN=1;
return (status);
}
void write_rf_data(uchar reg,uchar *data_ptr,uchar nLength)
{
uchar i;
CSN=0;
SPI_rf_write(reg);
for(i=0;i<nLength;i++)
SPI_rf_write(*data_ptr++);
CSN=1;
}
uchar read_rf_data(uchar reg,uchar *data_ptr,uchar nLength)
{
uchar i,status;
CSN=0;
SPI_rf_write(reg);
for(i=0;i<nLength;i++)
data_ptr[nLength]=SPI_rf_read();
status=SPI_rf_read();
CSN=1;
return(status);
}
/*
uchar SPI_Read_Buf(BYTE reg, BYTE *pBuf, BYTE bytes)
{
uchar status,byte_ctr;
CSN = 0; // Set CSN low, init SPI tranaction
status = SPI_RW(reg); // Select register to write to and read status byte
for(byte_ctr=0;byte_ctr<bytes;byte_ctr++)
pBuf[byte_ctr] = SPI_RW(0); // Perform SPI_RW to read byte from nRF24L01
CSN = 1; // Set CSN high again
return(status); // return nRF24L01 status byte
}
void Set_TX()
{
CE=0;
write_rf_data(WRITE_REG + RX_ADDR_P0,TX_ADDRESS,TX_ADR_WIDTH);
write_rf_data(WR_TX_PLOAD,tx_buf,TX_PLOAD_WIDTH);
write_rf_reg(WRITE_REG + CONFIG,0x0e);
CE=1;
delays(130);
} */
void Set_RX()
{
CE=0;
write_rf_reg(WRITE_REG + CONFIG,0x0f);
write_rf_reg(WRITE_REG + RX_PW_P0,TX_PLOAD_WIDTH);
CE=1;
delays(130);
}
void init_24L01()
{
CE=0;
write_rf_data(WRITE_REG + TX_ADDR,TX_ADDRESS,TX_ADR_WIDTH);
write_rf_data(WRITE_REG + RX_ADDR_P0,TX_ADDRESS,TX_ADR_WIDTH);
write_rf_reg(WRITE_REG + EN_AA,0x01);
write_rf_reg(WRITE_REG + EN_RXADDR,0x01);
write_rf_reg(WRITE_REG + SETUP_RETR,0x1a);
write_rf_reg(WRITE_REG + RF_CH,40);
write_rf_reg(WRITE_REG + RF_SETUP,0x0f);
write_rf_reg(WRITE_REG + CONFIG,0x0f);
CE=1;
//delays(130);
// flush_rf_tx();
// flush_rf_rx();
}
/*The foregoing program is achieve by HardWare SPI*/
/*
uchar SPI_RW(uint byte)
{
uchar bit_ctr;
for(bit_ctr=0;bit_ctr<8;bit_ctr++) // output 8-bit
{
MOSI = (byte & 0x80); // output 'byte', MSB to MOSI
byte = (byte << 1); // shift next bit into MSB..
SCK = 1; // Set SCK high..
byte |= MISO; // capture current MISO bit
SCK = 0; // ..then set SCK low again
}
return(byte); // return read byte
}
uchar SPI_RW_Reg(BYTE reg, BYTE value)
{
uchar status;
CSN = 0; // CSN low, init SPI transaction
status = SPI_RW(reg); // select register
SPI_RW(value); // ..and write value to it..
CSN = 1; // CSN high again
return(status); // return nRF24L01 status byte
}
BYTE SPI_Read(BYTE reg)
{
BYTE reg_val;
CSN = 0; // CSN low, initialize SPI communication...
SPI_RW(reg); // Select register to read from..
reg_val = SPI_RW(0); // ..then read registervalue
CSN = 1; // CSN high, terminate SPI communication
return(reg_val); // return register value
}
uchar SPI_Read_Buf(BYTE reg, BYTE *pBuf, BYTE bytes)
{
uchar status,byte_ctr;
CSN = 0; // Set CSN low, init SPI tranaction
status = SPI_RW(reg); // Select register to write to and read status byte
for(byte_ctr=0;byte_ctr<bytes;byte_ctr++)
pBuf[byte_ctr] = SPI_RW(0); // Perform SPI_RW to read byte from nRF24L01
CSN = 1; // Set CSN high again
return(status); // return nRF24L01 status byte
}
uchar SPI_Write_Buf(BYTE reg, BYTE *pBuf, BYTE bytes)
{
uchar status,byte_ctr;
CSN = 0; // Set CSN low, init SPI tranaction
status = SPI_RW(reg); // Select register to write to and read status byte
for(byte_ctr=0; byte_ctr<bytes; byte_ctr++) // then write all byte in buffer(*pBuf)
SPI_RW(*pBuf++);
CSN = 1; // Set CSN high again
return(status); // return nRF24L01 status byte
}
void Set_RX()
{
CE=0;
SPI_RW_Reg(WRITE_REG + CONFIG,0x0f);
SPI_RW_Reg(WRITE_REG + RX_PW_P0,TX_PLOAD_WIDTH);
CE=1;
delays(130);
}
void Set_TX()
{
CE=0;
SPI_Write_Buf(WRITE_REG + RX_ADDR_P0,TX_ADDRESS,TX_ADR_WIDTH);
SPI_Write_Buf(WR_TX_PLOAD,tx_buf,TX_PLOAD_WIDTH);
SPI_RW_Reg(WRITE_REG + CONFIG,0x0e);
CE=1;
delays(130);
}
void init_24L01()
{ CE=0;
SPI_Write_Buf(WRITE_REG + TX_ADDR, TX_ADDRESS, TX_ADR_WIDTH); // Writes TX_Address to nRF24L01
SPI_Write_Buf(WRITE_REG + RX_ADDR_P0,TX_ADDRESS, TX_ADR_WIDTH);
SPI_RW_Reg(WRITE_REG + EN_AA, 0x01); // Enable Auto.Ack:Pipe0
SPI_RW_Reg(WRITE_REG + EN_RXADDR, 0x01); // Enable Pipe0
SPI_RW_Reg(WRITE_REG + SETUP_RETR, 0x1a); // 500us + 86us, 10 retrans...
SPI_RW_Reg(WRITE_REG + RF_CH,100); // Select RF channel 40
SPI_RW_Reg(WRITE_REG + RF_SETUP, 0x0f); // TX_PWR:0dBm, Datarate:2Mbps, LNA:HCURR
SPI_RW_Reg(WRITE_REG + CONFIG, 0x0e); // Set PWR_UP bit, enable CRC(2 bytes) & Prim:TX. MAX_RT & TX_DS enabled..
CE=1;
}
/*void RX_Mode(void)
{
CE=0;
SPI_Write_Buf(WRITE_REG + RX_ADDR_P0, TX_ADDRESS, TX_ADR_WIDTH); // Use the same address on the RX device as the TX device
SPI_RW_Reg(WRITE_REG + EN_AA, 0x01); // Enable Auto.Ack:Pipe0
SPI_RW_Reg(WRITE_REG + EN_RXADDR, 0x01); // Enable Pipe0
SPI_RW_Reg(WRITE_REG + RF_CH, 40); // Select RF channel 40
SPI_RW_Reg(WRITE_REG + RX_PW_P0, TX_PLOAD_WIDTH); // Select same RX payload width as TX Payload width
SPI_RW_Reg(WRITE_REG + RF_SETUP, 0x0f); // TX_PWR:0dBm, Datarate:2Mbps, LNA:HCURR
SPI_RW_Reg(WRITE_REG + CONFIG, 0x0f); // Set PWR_UP bit, enable CRC(2 bytes) & Prim:RX. RX_DR enabled..
CE = 1; // Set CE pin high to enable RX device
delay(130);
// This device is now ready to receive one packet of 16 bytes payload from a TX device sending to address
// '3443101001', with auto acknowledgment, retransmit count of 10, RF channel 40 and datarate = 2Mbps.
}
void TX_Mode(void)
{
CE=0;
// RX_Addr0 same as TX_Adr for Auto.Ack
SPI_Write_Buf(WR_TX_PLOAD, tx_buf, TX_PLOAD_WIDTH); // Writes data to TX payload
SPI_RW_Reg(WRITE_REG + EN_AA, 0x01); // Enable Auto.Ack:Pipe0
SPI_RW_Reg(WRITE_REG + EN_RXADDR, 0x01); // Enable Pipe0
SPI_RW_Reg(WRITE_REG + RF_CH,40); // Select RF channel 40
SPI_RW_Reg(WRITE_REG + RF_SETUP, 0x0f); // TX_PWR:0dBm, Datarate:2Mbps, LNA:HCURR
SPI_RW_Reg(WRITE_REG + SETUP_RETR, 0x1a); // 500us + 86us, 10 retrans...
SPI_RW_Reg(WRITE_REG + CONFIG, 0x0e); // Set PWR_UP bit, enable CRC(2 bytes) & Prim:TX. MAX_RT & TX_DS enabled..
CE=1;
delays(130);
*/
/*Got a baby mistake,false key set if key equal 1 enter to function -_-!
void led_shake()
{
led=0;
delays(500);
led=1;
delays(500);
} //实现按键循环，不实现连续按键组合 */
/*void judge_BT()
{
int i;
uchar *a;
uchar *b;
uchar *c;
switch(t)
{
case 1:
a=Original_ADDRESS;
b=OnePress_ADDRESS;
for(i=0;i<5;i++)
{
*a=*b;
a++;
b++;
} tf=1;
break;
case 2:
i=0;
a=Original_ADDRESS;
c=TX_ADDRESS;
for(i=0;i<5;i++)
{
*a=*c;
a++;
b++;
} tf=1;
break;
}
if(tf)
{
tf=0;
Set_TX();
}
}
void CheckButtons()
{
// uchar temp;
// key=0xff;
// uchar s;
if(key==0)
{
delays(100);
if(key==0)
{
led_shake();
t++;
}
}
tx_buf[1]='d';
Set_TX();
delays(100);
Set_RX();
} */
/*Init HardWare SPI*/
void Init_SPI(void)
{
SPI0CFG = 0x40;
SPI0CN = 0x01; //(This Register can control SCK Pin High Or Low??The function of the pin is Enable/disable SPI..why add by lsy)
SPI0CKR = 0x01;
}
void init_mcu(void)
{
// unsigned int i;
P0MDIN = 0xff; // 01100010
P0MDOUT = 0x9d; //0:open-drain, 1:push pull (important Setting,If The port ain't the open-drain Mode,It won't be receive any data from register)add by lsy
P1MDIN = 0xff; // P1 are digital
P1MDOUT = 0xff; //0:open-drain, 1:push pull
P2MDIN = 0xff;
P2MDOUT = 0xff; // P2.2 and P2.3 set to push-pull
P3MDIN = 0xff;
P3MDOUT = 0x00;
// P0SKIP=0x3f; (This is a question,Wait for answer add by lsy)
P0 = 0xff;
P1 = 0xff;
P2 = 0xff;
P3 = 0xff;
IT01CF = 0x65;
XBR0 = 0x02;
XBR1 = 0x40; // Enable Crossbar
TMOD = 0x11; //T0,T1 as 16bits Timer mode
PCON = 0;
CKCON = 0x76; //Clock Control Register
TMR2CN = 0x00; //Timer2 Control Register
TMR3CN = 0xc0; //Timer3 .......
TMR3RLL = 0x00; //Timer3 Reload Register Low Byte
TMR3RLH = 0x00; //.......................High..
TMR2RLL = 0;
TMR2RLH = 0;
/*TR0 = 1; //Enable Mcu Timer
TR1 = 1;
TR2 = 1;
ET2 = 1; //Timer interrupt Enable flag
EX0 = 1;
EX1 = 1;
IT0 = 1; //Extern interrput Enable flag
IT1 = 1;
PX0 = 1; */
}
/*To check the register value if the register value is ture,make sure the communication pipe */
void CheckRS()
{
uchar reg_val;
reg_val=read_rf_reg(EN_AA);
reg_val=read_rf_reg(EN_RXADDR);
reg_val=read_rf_reg(RF_CH);
reg_val=read_rf_reg(RF_SETUP);
reg_val=read_rf_reg(SETUP_RETR);
reg_val=read_rf_reg(CONFIG);
reg_val=read_rf_reg(RX_PW_P0);
}
/*经过测试，CE，CSN，IRQ三个引脚都可以成功的翻转，输出方波，MOSI输出锯齿波，SCK和MISO则无反应*/
void main (void)
{
u16 i = 0;
PCA0MD &= ~0x40; // Disable Watchdog timer
VDM0CN = 0x80; // Enable VDD Monitor
delay(100); // wait for VDD Monitor stable
RSTSRC = 0x06;
SYSCLK_Init(); //init System Clock //init mcu -_-!
init_mcu();
init_io();
init_int0();
Init_SPI();
init_24L01();
CheckRS();
Set_RX();
while(1)
{
if(flag)
{
delays(100);
if(flag)
{
flag=0;
led=0;
delays(500);
led=~led;
delays(500);
}
}
}
}
// CheckButtons();
/*for(d=0;d<0xff;d++)
{
tx_buf[1]=d;
}
Set_TX();
// delays(100);
} */
void ISR_int0(void) interrupt 0
{
sta=read_rf_reg(STATUS); // read register STATUS's value
if(RX_DR) // if receive data ready (RX_DR) interrupt
{
CE=0;
read_rf_data(RD_RX_PLOAD,rx_buf,TX_PLOAD_WIDTH);
CE=1;
flag=1;
}
if(MAX_RT)
{
write_rf_reg(FLUSH_TX,0);
}
write_rf_reg(WRITE_REG + STATUS,sta);// clear RX_DR or TX_DS or MAX_RT interrupt flag
} ⌨️ 快捷键说明
复制代码
Ctrl + C
搜索代码
Ctrl + F
全屏模式
F11
切换主题
Ctrl + Shift + D
显示快捷键
?
增大字号
Ctrl + =
减小字号
Ctrl + -