cycle
共 108 篇文章
cycle 相关的电子技术资料，包括技术文档、应用笔记、电路设计、代码示例等，共 108 篇文章，持续更新中。
蚁群算法 控制台程序 基于类 不是基本的TSP模型的ant-cycle算法 而是蚁群系统 ant colony system算法
蚁群算法
控制台程序
基于类
不是基本的TSP模型的ant-cycle算法
而是蚁群系统 ant colony system算法
The BuildBot is a system to automate the compile/test cycle required by most software projects. CVS
The BuildBot is a system to automate the compile/test cycle required by most software projects. CVS commits trigger new builds, run on a variety of client machines. Build status (pass/fail/etc) are di
Edge Disjoint Cycles. You are given an input graph that is either directed or undirected. Write a pr
Edge Disjoint Cycles. You are given an input graph that is either directed or undirected. Write a program that reads in a vertex number and lists the number of edge disjoint cycles that start and end
Ring register[1 from 8] which seven speeds. The result is presented on 8 LEDs. After every cycle, sp
Ring register[1 from 8] which seven speeds. The result is presented on 8 LEDs. After every cycle, speed grows. The process starts again after last 8 cycle.
It contains a vhdl description of the external bus interface unit for 68000 processor. currently onl
It contains a vhdl description of the external bus interface unit for 68000 processor. currently only read and write cycle are supported
AP2406技术手册
The AP2406 is a 1.5Mhz constant frequency, slope compensated current mode PWM step-down converter. The device integrates a main switch and a synchronous rectifier for high efficiency without an extern
实现产生伪随机序列的部件 —— 线性反馈移位寄存器单元。 SFlog2为扩频因子的底数为2的对数值
实现产生伪随机序列的部件 —— 线性反馈移位寄存器单元。 SFlog2为扩频因子的底数为2的对数值，cycle为PN序列的周期，其值为2^SFlog2。initial_state为移位寄存器的初始状态，generator_polynomial_coefficient为生成PN序列所需的本原多项式，对应于移位寄存器的连接向量。
用Fourier变换求取信号的功率谱---周期图法 用Fourier变换求取信号的功率谱---分段周期图法 用Fourier变换求取信号的功率谱---welch方法 功率谱估计----多窗口法（
用Fourier变换求取信号的功率谱---周期图法
用Fourier变换求取信号的功率谱---分段周期图法
用Fourier变换求取信号的功率谱---welch方法
功率谱估计----多窗口法（multitaper method ,MTM法）
功率谱估计----最大熵法（maxmum entmpy method,MEM法）
功率谱估计----多信号分类法（multiple signal
SimpliciTI™ -1.0.4.exe for CC2430 SimpliciTI is a simple low-power RF network protocol aimed
SimpliciTI™ -1.0.4.exe for CC2430
SimpliciTI is a simple low-power RF network protocol aimed at small (<256) RF networks. Such networks typically contain battery operated devices which requi
This example demonstrates the use of the ADC block and PWM blocks. The generated DSP code produces t
This example demonstrates the use of the ADC block and PWM blocks. The generated DSP code produces the pulse waveform whose duty cycle is changing as the voltage applied to ADC input changes. The wave
tas3204
<div class="description" id="descriptions" style="box-sizing:border-box;float:left;width:570.958312988281px;color:#555555;font-family:'Microsoft YaHei', 微软雅黑, SimSun, 宋体, sans-serif;font-size:14px;lin
matlab雨流算法。The rain flow algorithm code has been prepared according to the ASTM standard (Standard p
matlab雨流算法。The rain flow algorithm code has been prepared according to the ASTM standard (Standard practices for cycle counting in fatigue analysis) and optimized considering the calculation time.
show 0-F cycle by cycle in ARM7
show 0-F cycle by cycle in ARM7
Each arc of a binary-state network has good/bad states. The system reliability, the probability tha
Each arc of a binary-state network has good/bad states. The system reliability, the probability
that source s communicates with sink t, can be computed in terms of minimal paths (MPs). An
MP is an o
Singal Cycle MIPS
Single MIPS CPU in FPGA.
Turbo Decoder Release 0.3 * Double binary, DVB-RCS code * Soft Output Viterbi Algorithm * MyHDL c
Turbo Decoder Release 0.3
* Double binary, DVB-RCS code
* Soft Output Viterbi Algorithm
* MyHDL cycle/bit accurate model
* Synthesizable VHDL model
IDCT-M is a medium speed 1D IDCT core -- it can accept a continous stream of 12-bit input words at
IDCT-M is a medium speed 1D IDCT core
-- it can accept a continous stream of 12-bit input words at a rate of
-- 1 bit/ck cycle, operating at 50MHz speed, it can process MP@ML MPEG video
-- the core
Simple I2C controller -- 1) No multimaster -- 2) No slave mode -- 3) No fifo s -- -- notes:
Simple I2C controller
-- 1) No multimaster
-- 2) No slave mode
-- 3) No fifo s
--
-- notes:
-- Every command is acknowledged. Do not set a new command before previous is acknowledged.
-- Dout
he LPC932 can be used to create a Pulse Width Modulated PWM signal. That s an analog signal, with on
he LPC932 can be used to create a Pulse Width Modulated PWM signal. That s an analog signal, with only 2 discrete levels, for example 0V and 5V and a constant period. The current value of this signal
用C51实现无功补偿中电容组循环投切的算法
<P>介绍了用单片机C 语言实现无功补偿中电容组循环投切的基本原理和算法，并举例说<BR>明。<BR>关键词：循环投切;C51;无功补偿<BR>中图分类号： TM76 文献标识码： B<BR>Abstract: This paper introduces the aplication of C51 in the controlling of capacitor<BR>suits cycle pow