configured
共 59 篇文章
configured 相关的电子技术资料，包括技术文档、应用笔记、电路设计、代码示例等，共 59 篇文章，持续更新中。
花园控制灯
The l.e.d.s are turned on by a light-sensitive controller, formed around op.amp IC1,configured as a comparator. The ambient light level is detected by a light dependent resistor, R1. Its sensitivity
TB62726AF
UCC28051 Evaluation Module is a 100-W offline AC-DC voltage converter with power factor correction (PFC). The power module was designed to show how the UCC28051 could be configured in an off-line powe
AL422B
The AL422B consists of 3M-bits of DRAM, and is configured as 393,216 words x 8 bit FIFO (first
in first out). The interface is very user-friendly since all complicated DRAM operations are already
ma
93C46英文版
The Microchip Technology Inc. 93C46B is a 1K-bit,
low-voltage serial Electrically Erasable PROM. The
device memory is configured as 64 x 16 bits. Advanced
CMOS technology makes this device ideal fo
可编程逻辑器件在带电插入应用中的影响以及在进行带电插入设计中的其他因素的考虑
The PLC42VA12 contains 10 flip-flops that<BR>may flexibly be configured to build counters,<BR>shifte
采用阻抗测量技术 CS5516 CS5520 A D转换器可以用于精密温度测量
The CS5516/CS5520 bridge-measurement A/D<BR>converters can be configured for precise<BR>measurement
效率85％的12v转5v降压转换器
This application note describes how the NCP3063 can be configured as a buck controller to drive an e
基于单片机的酒驾检测系统设计
<p>为增加酒精传感器测量点数,同时监测传感器是否损坏,基于UCOS操作系统和STM32F4单片机,设计实现了多通道实时酒精测量与数据存储系统。传感序列共可连接10个MQ-3酒精传感器,并为每个传感器预留了DS18B20温度检测接口,实时监测传感器温度变化。传感序列任务设置相同优先级为10,采用时间片轮转调度实现序列任务间的切换。配置LCD触摸屏实现人机交互,基于STemWin设计制作了系统图形化
基于MCGS的STC15单片机驱动构件开发
<p>MCGS组态软件提供了一种脚本驱动开发工具,用户使用该工具可便捷开发满足项目需求的驱动构件。脚本驱动开发工具包含大量的标准函数,能充分满足用户需求。文章基于MCGS的STC15单片机驱动构件开发,根据水位监控系统的实际要求设计,首先确定通信协议,再配置设备属性、设备通道、编写设备命令与编辑调试,最后通过驱动构件的发布与应用,实现设备驱动构件的开发。</p><p>MCGS configurat
基于STM32单片机的穿戴式坐姿调整器的设计及其实现
<p>“穿戴式坐姿提醒器”是基于STM32最小系统,采用了模块化的设计理念对传统的坐姿矫正器赋予新的定义与本质,使其更加富有智能化与人性化。该“便携式坐姿提醒器”可以通过MPU6050陀螺仪实时感知人体的姿态,该陀螺仪采用了高灵敏度的6轴运动传感器,相对于佩戴者的身体角度,以及躯体动作时的加速度,角速度进行相应的运算,保证了数据的准确性,从而实现对人体的坐姿进行实时的“监视”,在人们出现不良的坐姿
PSoC4Demo例程
The goal of this lab is to learn the basics of the PSoC Creator IDE by implementing a simple,
software controlled blinking LED. A project is created, components are placed and configured,
pins are a
TI步进电机驱动芯片drv8825，32细分
The DRV8825 provides an integrated motor driver solution for printers, scanners, and other automated equipment applications. The device has two H-bridge drivers and a microstepping indexer, and is int
RTL8365MB芯片参数资料
<p>The RTL8365MB-CG is an LQFP128, high-performance 4+1-port 10/100/1000M Ethernet switch</p><p>featuring low-power integrated Quad-port Giga-PHYs that support 1000Base-T, 100Base-TX, and</p><p>10Base
USB挂起与唤醒
<p style="white-space: normal;">USB挂起与唤醒，供学习。</p><p style="white-space: normal;">USB可见设备状态分为连接(Attached)，上电(Powered)，默认(Default)，地址(Address)，配置(Configured)和挂起(Suspended)6个状态。</p><p><br/></p>
Understanding_the_Basics_of_MIMO
An acronym for Multiple-In, Multiple-Out, MIMO communication sends the same data as several signals<br />
simultaneously through multiple antennas, while still utilizing a single radio channel. This i
This program requires the DSP2833x header files. // // This program requires an external I2C RT
This program requires the DSP2833x header files.
//
// This program requires an external I2C RTC connected to
// the I2C bus at address 0x6f.
//
// As supplied, this project is configure
The objective is to set up SPI communication between VTI Technologies digital pressure sensor comp
The objective is to set up SPI communication between VTI Technologies digital pressure sensor
component and an MCU of an application device ATMEGA16L. In this code example:
?The MCU is configured
A few drivers for the Motorola C380 s celluar phone hardware with a simple test application. It s co
A few drivers for the Motorola C380 s celluar phone hardware with a simple test application. It s configured to build a binary that is to be uploaded at 0x03fd0000 and run at 0x03fd0010
This example application requires several components to be setup and configured before running. It
This example application requires several components to be setup and configured before running. It
is assumed that you understand how to setup a Web application and add the components below.
ST32 基于（英蓓特）STM32V100的EXTI程序 This example shows how to configure an external interrupt line. In t
ST32
基于（英蓓特）STM32V100的EXTI程序
This example shows how to configure an external interrupt line.
In this example, the EXTI line 9 is configured to generate an interrupt on each
falling edge. In the in