Quake 3 s MD3 Viewer (july 13, 2007), loads and displays a player and a weapon. supports lighting, texture mapping and animation. Includes a sample player model with weapon. See README for how to use it. Note (1): it uses the POSIX opendir/readdir functions, which are not implemented in all compilers under Windows (MinGW supports them). Note (2): This demo works on little endian architectures only. Libraries: OpenGL, GLU, GLUT, boost, libjpeg. Files: md3loader.zip (2.4 MB)
标签： and supports displays lighting
上传时间： 2017-09-10
上传用户：czl10052678
This driver supports both master mode, slave mode & mixed mode operation.
标签： mode operation supports driver
上传时间： 2013-12-11
上传用户：894898248
This release supports Microsoft Windows NT 4.0, Windows 2000, Windows 95, Windows 98, Windows Me, Windows XP, Red Hat Linux 6.1, Red Hat Linux 7.2, Solaris 2.6, 2.7 (7.0), 8.0, HP-UX 10.20, and 11 (see important note below)." multice22.rar
上传时间： 2013-05-29
上传用户：hustfanenze
·详细说明：支持SD卡的MP3电路图,powerpcb4.0格式.使用AVR单片机- supports SD the card the MP3 circuit diagram, the powerpcb4.0 form Uses the AVR monolithic integrated circuit
上传时间： 2013-06-05
上传用户：zhaoq123
The LTC®3569 is a compact power solution for handhelddevices. Its tiny 3mm × 3mm QFN package includesthree buck regulators with individually programmableoutput voltages. One regulator supports load currentsup to 1200mA, while the other two support currents to600mA. Two regulators can be paralleled for increasedload capability. Each current-mode regulator is internallycompensated with excellent load and line regulation. Acomplete 2- or 3-output solution requires a minimumof external passive components.
上传时间： 2013-10-11
上传用户：yxgi5
Digitemp Junior – An RS-232 Port-Powered Digital Thermometer Digitemp Jr. is a device that is designed to measure and report ambient temperature. When connected to an RS-232 port on any PC, it will periodically measure and report in ASCII form the ambient temperature in degrees Celsius. These temperature readings can be monitored with any terminal program. If the terminal program supports capture to disk, the temperature readings can be saved to disk for further analysis with a spreadsheet program or other data analysis tool. The simple ASCII output format of Digitemp Jr. makes it rel- atively easy to write custom software for receiving, recording, and analyzing ambient temperature data. Best of all, Digitemp Jr. requires no external power sup- plies or batteries. It is powered directly by the RS-232 port.
上传时间： 2013-10-20
上传用户：baitouyu
Digitemp Jr. is a device that is designed to measure and report ambient temperature. When connected to an RS-232 port on any PC, it will periodically measure and report in ASCII form the ambient temperature in degrees Celsius. These temperature readings can be monitored with any terminal program. If the terminal program supports capture to disk, the temperature readings can be saved to disk for further analysis with a spreadsheet program or other data analysis tool. The simple ASCII output format of Digitemp Jr. makes it relatively easy to write custom software for receiving, recording, and analyzing ambient temperature data. Best of all, Digitemp Jr. requires no external power supplies or batteries. It is powered directly by the RS-232 port.
上传时间： 2013-10-20
上传用户：Maple
The MSP-FET430PIF is a Parallel Port interface (does not include target board) that is used to program and debug MSP430 FET tools and test boards through the JTAG interface. This interface is included in our FET tools, but sold without the development board. This interface uses a Parallel PC Port to communicate to the Debugger Software (IAR Kickstart software included) running on the PC. The interface uses the standard 14 pin header to communicate to the MSP430 device using the standard JTAG protocol. The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is extremely low power, no external power supply is required. The tool has an integrated software environment and connects directly to the PC which greatly simplifies the set-up and use of the tool. The flash development tool supports development with all MSP430 flash parts. Features MSP430 debugging interface to connect a MSP430-Flash-device to a Parallel port on a PC supports JTAG debug protocol (NO support for Spy-Bi-Wire (2-wire JTAG) debug protocol, Spy-Bi-Wire (2-wire JTAG) is supported by MSP-FET430UIF) Parallel Port cable and a 14-conductor target cable Full documentation on CD ROM Integrated IAR Kickstart user interface which includes: Assembler Linker Limulator Source-level debugger Limited C-compiler Technical specifications: Backwardly compatable with existing FET tool boards.
上传时间： 2013-10-26
上传用户：fengweihao158@163.com
The MSP-FET430U14 is a powerful flash emulation tool to quickly begin application development on the MSP430 MCU. It includes USB debugging interface used to program and debug the MSP430 in-system through the JTAG interface or the pin saving Spy Bi-Wire (2-wire JTAG) protocol. The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is ultra-low power, no external power supply is required. The debugging tool interfaces the MSP430 to the included integrated software environment and includes code to start your design immediately. The MSP-FET430UIF development tools supports development with all MSP430 flash devices
上传时间： 2013-10-28
上传用户：13691535575
The CAT25128 is a 128−Kb Serial CMOS EEPROM device internally organized as 16Kx8 bits. This features a 64−byte page write buffer and supports the Serial Peripheral Interface (SPI) protocol. The device is enabled through a Chip Select (CS) input. In addition, the required bus signals are clock input (SCK), data input (SI) and data output (SO) lines. The HOLD input may be used to pause any serial communication with the CAT25128 device. The device featuressoftware and hardware write protection, including partial as well as full array protection.
上传时间： 2013-11-15
上传用户：fklinran
