针对目前CT 设备控制系统成本高、体积大的缺点,开发了以P89V51RD2 单片机为核心完成运动控制、信号采集及USB 通信等功能的CT 实验仪嵌入式控制系统。讨论了控制系统的总体设计方案,详细介绍了主要的硬件结构和软件流程。实际应用表明,该控制系统性能可靠、成本低、使用方便。
上传时间: 2013-11-09
上传用户:Miyuki
特点 精确度0.25%滿刻度 ±1位數 输入配线系统可任意选择 CT比可任意设定 具有异常电流值与异常次数记录保留功能 电流过高或过低检测可任意设定 报警继电器复归方式可任意設定 尺寸小,穩定性高 2.主要規格 辅助电源: AC110V&220V ±20%(50 or 60Hz) AC220V&440V ±20%(50 or 60Hz)(optional) 精确度: 0.25% F.S. ±1 digit 输入负载: <0.2VA (Current) 最大过载能力 : Current related input: 2 x rated continuous 10 x rated 30 sec. 25 x rated 3sec. 50 x rated 1 sec. 输入电流范围: AC0-5A (10-1000Hz) CT ratio : 1-2000 adjustable 启动延迟动作时间: 0-99.9 second adjustable 继电器延迟动作时间: 0-99.9 second adjustable 继电器复归方式: Manual (N) / latch(L) can be modified 继电器磁滞范围: 0-999 digit adjustable 继电器动作方向: HI /LO/GO/HL can be modified 继电器容量: AC 250V-5A, DC 30V-7A 过载显示: "doFL" 温度系数: 50ppm/℃ (0-50℃) 显示幕: Red high efficiency LEDs high 14.22mm(.56")(PV) Red high efficiency LEDs high 14.22mm(.276")(NO) 参数设定方式: Touch switches 记忆型式 : Non-volatile E2PROM memory 绝缘耐压能力: 2KVac/1 min. (input/output/power) 1600Vdc(input/output 使用环境条件 : 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间: 2013-10-14
上传用户:wanghui2438
Visual Assist X 10.6.1822.0(VC6.0智能插件)
上传时间: 2013-12-14
上传用户:ysystc670
MATLAB5[x]入门与提高.
标签: MATLAB5
上传时间: 2014-01-25
上传用户:fairy0212
Allegro15[1].X培训教材
上传时间: 2014-01-08
上传用户:qzhcao
The Virtex-4 features, such as the programmable IDELAY and built-in FIFO support, simplifythe bridging of a high-speed, PCI-X core to large amounts of DDR-SDRAM memory. Onechallenge is meeting the PCI-X target initial latency specification. PCI-X Protocol Addendum tothe PCI Local Bus Specification Revision 2.0a ([Ref 6]) dictates that when a target signals adata transfer, "the target must do so within 16 clocks of the assertion of FRAME#." PCItermination transactions, such as Split Response/Complete, are commonly used to meet thelatency specifications. This method adds complexity to the design, as well as additional systemlatency. Another solution is to increase the ratio of the memory frequency to the PCI-X busfrequency. However, this solution increases the required power and clock resource usage.
上传时间: 2013-11-24
上传用户:18707733937
微电脑型单相交流集合式电表(单相二线系统) 特点: 精确度0.25%满刻度±1位数 可同时量测与显示交流电压,電流,頻率,瓦特,(功率因數/視在功率) 交流電壓,電流,瓦特皆為真正有效值(TRMS) 交流電流,瓦特之小數點可任意設定 瓦特單位W或KW可任意設定 CT比可任意設定(1至999) 輸入與輸出絕緣耐压 2仟伏特/1分鐘( 突波測試強度4仟伏特(1.2x50us) 數位RS-485界面 (Optional) 主要规格: 精确度: 0.1% F.S.±1 digit (Frequency) 0.25% F.S.±1 digit(ACA,ACV,Watt,VA) 0.25% F.S. ±0.25o(Power Factor) (-.300~+.300) 输入负载: <0.2VA (Voltage) <0.2VA (Current) 最大过载能力: Current related input: 3 x rated continuous 10 x rated 30 sec. 25 x rated 3sec. 50 x rated 1sec. Voltage related input: maximum 2 x rated continuous 过载显示: "doFL" 显示值范围: 0~600.0V(Voltage) 0~999.9Hz(Frequency)(<20% for voltage input) 0~19999 digit adjustable(Current,Watt,VA) 取样时间: 2 cycles/sec. RS-485通讯位址: "01"-"FF" RS-485传输速度: 19200/9600/4800/2400 selective RS-485通信协议: Modbus RTU mode 温度系数: 100ppm/℃ (0-50℃) 显示幕: Red high efficiency LEDs high 10.16 mm(0.4") 参数设定方式: Touch switches 记忆型式: Non-volatile E²PROM memory 绝缘抗阻: >100Mohm with 500V DC 绝缘耐压能力: 2KVac/1 min. (input/output/power) 1600 Vdc (input/output) 突波测试: ANSI c37.90a/1974,DIN-IEC 255-4 impulse voltage 4KV(1.2x50us) 使用环境条件: 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间: 2015-01-02
上传用户:几何公差
支持X/YModem和cis_b+协议的串口通讯程序
上传时间: 2014-01-17
上传用户:qweqweqwe
支持X/Y/Z Modem协议的传输文件的通讯程序
上传时间: 2015-01-03
上传用户:xg262122
X Windows下的迷宫程序
上传时间: 2015-01-03
上传用户:372825274