The PCA9535 and PCA9535C are 24-pin CMOS devices that provide 16 bits of GeneralPurpose parallel Input/Output (GPIO) expansion for I2C-bus/SMBus applications and wasdeveloped to enhance the NXP Semiconductors family of I2C-bus I/O expanders. Theimprovements include higher drive capability, 5 V I/O tolerance, lower supply current,Individual I/O configuration, and smaller packaging. I/O expanders provide a simplesolution when additional I/O is needed for ACPI power switches, sensors, push buttons,LEDs, fans, etc.
上传时间： 2013-10-21
上传用户：爱死爱死
The PCA9549 provides eight bits of high speed TTL-compatible bus switching controlledby the I2C-bus. The low ON-state resistance of the switch allows connections to be madewith minimal propagation delay. Any Individual A to B channel or combination of channelscan be selected via the I2C-bus, determined by the contents of the programmable Controlregister. When the I2C-bus bit is HIGH (logic 1), the switch is on and data can flow fromPort A to Port B, or vice versa. When the I2C-bus bit is LOW (logic 0), the switch is open,creating a high-impedance state between the two ports, which stops the data flow.An active LOW reset input (RESET) allows the PCA9549 to recover from a situationwhere the I2C-bus is stuck in a LOW state. Pulling the RESET pin LOW resets the I2C-busstate machine and causes all the bits to be open, as does the internal power-on resetfunction.
上传时间： 2014-11-22
上传用户：xcy122677
The PCA9546A is a quad bidirectional translating switch controlled via the I2C-bus. TheSCL/SDA upstream pair fans out to four downstream pairs, or channels. Any IndividualSCx/SDx channel or combination of channels can be selected, determined by thecontents of the programmable control register.
上传时间： 2013-11-15
上传用户：cc1915
The PCA9555 is a 24-pin CMOS device that provides 16 bits of General Purpose parallelInput/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed toenhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvementsinclude higher drive capability, 5 V I/O tolerance, lower supply current, Individual I/Oconfiguration, and smaller packaging. I/O expanders provide a simple solution whenadditional I/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, etc.The PCA9555 consists of two 8-bit Configuration (Input or Output selection); Input, Outputand Polarity Inversion (active HIGH or active LOW operation) registers. The systemmaster can enable the I/Os as either inputs or outputs by writing to the I/O configurationbits. The data for each Input or Output is kept in the corresponding Input or Outputregister. The polarity of the read register can be inverted with the Polarity Inversionregister. All registers can be read by the system master. Although pin-to-pin and I2C-busaddress compatible with the PCF8575, software changes are required due to theenhancements, and are discussed in Application Note AN469.
上传时间： 2013-11-13
上传用户：fredguo
The PCA9548A is an octal bidirectional translating switch controlled via the I2C-bus. TheSCL/SDA upstream pair fans out to eight downstream pairs, or channels. Any IndividualSCx/SDx channel or combination of channels can be selected, determined by thecontents of the programmable control register.An active LOW reset input allows the PCA9548A to recover from a situation where one ofthe downstream I2C-buses is stuck in a LOW state. Pulling the RESET pin LOW resets theI2C-bus state machine and causes all the channels to be deselected as does the internalPower-on reset function.
上传时间： 2013-10-13
上传用户：bakdesec
The Philips family of Multiplexers and Switches consists of bi-directional translating switches controlled via the I2C or SMBus to fan out an upstream SCL/SDA pair to 2, 4 or 8 downstream channels of SCx/SDx pairs. The Multiplexers allow only one downstream channel to be selected at a time, while the Switches allow any Individual downstream channel or combination of downstream channels to be selected, depending on the content of the programmable control register. Once one or several channels have been selected, the device acts as a wire, allowing the master on the upstream channel to send commands to devices on all the active downstream channels, and devices on the active downstream channels to communicate with each other and the master. External pull-up resistors are used to pull each Individual channel up to the desired voltage level. Combined interrupt output and hardware reset input are device options that are featured.
上传时间： 2013-10-11
上传用户：dianxin61
Abstract: This application note explains the hardware of different types of 1-Wire® interfaces and software examples adapted to this hardware with a focus on serial ports. Depending on the types of iButtons required for a project and the type of computer to be used, the most economical interface is easily found. The hardware examples shown are basically two different types: 5V general interface and 12V RS-232 interface. Within the 5V group a common printed circuit board could be used for all circuits described. The variations can be achieved by different populations of components. The same principal is used for the 12V RS-232 interface. The population determines if it is a Read all or a Read/Write all type of interface. There are other possible circuit implementations to create a 1-Wire interface. The circuits described in this application note cover many different configurations. For a custom application, one of the described options can be adapted to meet Individual needs.
标签： iButtons Reading Writing and
上传时间： 2013-10-29
上传用户：long14578
Automobiles, aircraft, marine vehicles, uninterruptiblepower supplies and telecom hardware represent areasutilizing series connected battery stacks. These stacksof Individual cells may contain many units, reaching potentialsof hundreds of volts. In such systems it is oftendesirable to accurately determine each Individual cell’svoltage. Obtaining this information in the presence of thehigh “common mode” voltage generated by the batterystack is more diffi cult than might be supposed.
上传时间： 2013-10-24
上传用户：kang1923
This a simple genetic algorithm implementation where the evaluation function takes positive values only and the fitness of an Individual is the same as the value of the objective function
标签： implementation evaluation algorithm function
上传时间： 2015-04-12
上传用户：klin3139
SelectionDemo also has code (not included in the preceding snippet) that changes the table s selection orientation. By changing a couple of boolean values, you can make the table allow either column selections or Individual cell selections, instead of row selections.
标签： SelectionDemo the preceding included
上传时间： 2015-05-03
上传用户：gut1234567
