为解决我国水位监测野外条件下长期无人看守的问题，研制开发了基于MSP430单片机的智能水位计。从其组成到各功能分别进行了详细的介绍，该智能水位计不仅实现了水位数据的实时监测、记录和定期采集等多种工作模式，而且提高了水位监测精度，实现了水位监测的智能化。 Abstract: In order to solve the problems of long-term unmanned observation in the FIELD water monitoring，an intelligence water-level meter based on MSP430 is developed composition and every function moduce of the water level meter was introduced in detail. It not only realizes water level data collection and storage， regularly gathering and so on， but also improves the water-level precision ， finally realizes the intelligence.
上传时间： 2013-11-17
上传用户：417313137
针对众多低成本数据采集需求，采用带有片上USB控制器和D/A转换器的混合信号微处理器C8051F340，设计了一款可通过USB接口和LabVIEW图形用户界面实现与PC机联机的数据采集器，同时借助系统的SD卡存储独立实现现场长时间采集数据。该数据采集器成本低，结构简单，体积小，已成功用于工业现场。 Abstract: Aiming at the need of low cost data acquisition, a data acquisition device is designed based on C8051F340 which is a mixed-signal microcontroller and integrates USB controller and A/D controller on a chip.The data acquisition device which can combine with PC by USB interface and LabVIEW graphical user interface,can realize data acquisition. At the same time,it can be solely run a long time in virtue of SD card in FIELD.The date aequisition device features low cost,simple structure and little sharp, and it has been used in industry FIELD.
上传时间： 2014-05-31
上传用户：1109003457
为解决输油管道温度压力参数实时监测的问题，设计了以C8051F930单片机作为控制核心的超低功耗输油管道温度压力远程监测系统。现场仪表使用高精度电桥采集数据，通过433 MHz短距离无线通信网络与远程终端RTU进行通信，RTU通过GPRS网络与PC上位机进行远程数据传输，在上位机中实现数据存储和图形化界面显示，从而实现输油管道温度压力参数的实时监测和异常报警。经实验证明，该系统的12位数据采集精度满足设计要求，漏码率小于1%，正常工作时间超过5个月，能实时有效地监测输油管道的温度压力参数，节省大量人工成本，有效预防管道参数异常造成的经济损失和环境污染。 Abstract: In order to solve the problems on real-time monitoring of pipeline temperature and pressure parameters， the ultra-low power remote pipeline temperature and pressure monitoring system was designed by using the single chip processor C8051F930 as the control core. The high-precision electric bridge was used in FIELD instruments for data collection， the 433MHz short-range wireless communication network was used to make communication between FIELD instrument and RTU， the GPRS was used by the RTU to transmit data to the PC host computer， and the data was stored and displayed in the PC host computer， so the real-time monitoring and exception alerts of pipeline temperature and pressure parameters were achieved. The experiment proves that the system of which error rate is less than 1% over five months working with the 12-bit data acquisition accuracy can effectively monitor the pipeline temperature and pressure parameters in real time， it saves a lot of labor costs and effectively prevents environmental pollution and economic losses caused by abnormal channel parameters.
上传时间： 2013-11-06
上传用户：cuibaigao
介绍了一种基于MSP430系列单片机和ADXL203加速度传感器的数字式倾角仪，它不仅可以实现水平度检测，而且可以测量00～3600范围内的任意倾角，分辨率可达O．1。。此外，由于该倾角仪输出为数字结果，因此它也可以与其他的数字设备结合起来，组合成一个功能更加强大的仪器。该数字倾角仪可广泛应用于建筑、机械、道路、桥梁、石油、煤矿和地质勘探等各种需要测量重力参考系下倾角的场合。关键词：MSP430F133单片机；力敏传感器；ADXL203加速度计；角度测量 Abstract：This paper presents a new style digital inclinometer which is developed on the basis of the MSP430F133 MCU and the ADXL203 dual axis aeeelerometer．This inclinometer not only can test levelness，but also can measure any angle between 0。and 360。with an accuracy of 0．1 O．In addition，its output is a digital result，which makes it possible to integrate itself with other digital devices to form a more functional unit．This inclinometer can be widely used in any construction site，oil FIELD，coal-mine or geologic survey and SO on where it will provide the working people with convenience to measure any angles．Key words：MSP430F133 MCU；force sensor；ADXL203 accelerometer；angle measurement
上传时间： 2013-11-13
上传用户：lizhizheng88
汇编器在微处理器的验证和应用中举足轻重，如何设计通用的汇编器一直是研究的热点之一。本文提出了一种开放式的汇编器系统设计思想，在汇编语言与机器语言间插入中间代码CMDL（code mapping description language）语言，打破汇编语言与机器语言的直接映射关系，由此建立起一套描述汇编语言与机器语言的开放式映射体系。基于此开放式映射体系开发了一套汇编器系统，具有较高层次上的通用性和可移植性。【关键词】指令集，CMDL，汇编器，开放式 Design of Retargetable Assembler System Liu Ling Feng Wen Nan Wang Ying Chun Jiang An Ping Ji Li Jiu IME of Peking University, 100871【摘要】An assembler plays a very important role in the FIELD of microprocessor verifications and applications, thus how to build a retargetable assembler system has been a hotspot in this FIELD for long time. This paper presents a new method about the retargetable assembler system design.It provides a kind of language CMDL, code mapping description language. During the process of assembling, assembler languages are firstly translated to CMDL, and then mapped to the machine codes. In an other word, CMDL is inserted between assembler languages and machine codes during the translation procedure. As a medium code, CMDL has a lot of features, such as high extraction, strong descript capabilities. It can describe almost all attributes of assembler languages. By breaking the direct mapping relationship between assembler languages and machine codes, the complexities of machine codes are hided to the users, therefore, the new retargetable assembler system has higher retargetable level by converting the mapping from assembler languages and machine codes to assembler languages and CMDL, and implementationof it becomes easier. Based on the new mapping system structure, a retargetable assemblersystem is developed. It proved the whole system has good retargetability and implantability.【关键词】instruction set, symbol table, assembler, lexical analysis, retargetability
上传时间： 2013-10-09
上传用户：meiguiweishi
基于LabVIEW和单片机的空调温度场测量系统的研究:室内温度是空调系统舒适性的重要指标,对其及时、准确地测量显得非常重要。介绍单片机AT89C51 和数字式、单总线型温度传感器DS18B20 组成矩形测量网络采集空调室内40 点温度,LabVIEW作为开发平台,二者之间通过串口实现数据通信,利用LabVIEW强大的数据处理和显示功能对采集的空调温度场数据进行实时处理、分析和显示,详细介绍了系统的硬件结构和软件模块的设计方案。关键词:单片机;DS18B20 ;LabVIEW;串行通信 Abstract : Temperature is a very important criterion of air condition system′s comfort , so it is very significant to measure it accurately and real timely. This paper int roduces a data acquisition system of measuring 40 point s temperature for air condition room based on single wire digital sensor DS18B20 and microcont roller AT89C51 which are composed of rectangle measuring meshwork. The data communication between LabVIEW and microcont roller is executed via serial port ,and the temperature FIELD data of air condition room are processed analyzed and displayed on LabVIEW. The hardware and software modules are also given in detail.Keywords : single chip ;DS18B20 ;LabVIEW; serial communication
上传时间： 2014-05-05
上传用户：KSLYZ
The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 MicrocontrollerCore. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementationof the USB hardware directly on the chip, complying with the Universal Serial Bus Specification, Revision1.1.This application note describes a demonstration program that has been written for the DK3200 hardwaredemonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to workwith the device, using the HID class as a ready-made device driver for the USB connection.IN-APPLICATION-PROGRAMMING (IAP) AND IN-SYSTEM-PROGRAMMING (ISP)Since the μPSD contains two independent Flash memory arrays, the Micro Controller Unit (MCU) can executecode from one memory while erasing and programming the other. Product firmware updates in theFIELD can be reliably performed over any communication channel (such as CAN, Ethernet, UART, J1850)using this unique architecture. For In-Application-Programming (IAP), all code is updated through theMCU. The main advantage for the user is that the firmware can be updated remotely. The target applicationruns and takes care on its own program code and data memory.IAP is not the only method to program the firmware in μPSD devices. They can also be programmed usingIn-System-Programming (ISP). A IEEE1149.1-compliant JTAG interface is included on the μPSD. Withthis, the entire device can be rapidly programmed while soldered to the circuit board (Main Flash memory,Secondary Boot Flash memory, the PLD, and all configuration areas). This requires no MCU participation.The MCU is completely bypassed. So, the μPSD can be programmed or reprogrammed any time, anywhere, even when completely uncommitted.Both methods take place with the device in its normal hardware environment, soldered to a printed circuitboard. The IAP method cannot be used without previous use of ISP, because IAP utilizes a small amountof resident code to receive the service commands, and to perform the desired operations.
标签： Demonstration 3200 USB for
上传时间： 2014-02-27
上传用户：zhangzhenyu
为了扩大监控范围，提高资源利用率，降低系统成本，提出了一种多通道视频切换的解决方案。首先从视频信号分离出行场信号，然后根据行场信号由DSP和FPGA产生控制信号，控制多路视频通道之间的切换，从而实现让一个视频处理器同时监控不同场景。实验结果表明，该方案可以在视频监控告警系统中稳定、可靠地实现视频通道的切换。 Abstract: To expand the scope of monitoring， improve resource utilization， reduce system cost， a multiple video channels signal switching method is pointed out in this paper. First， horizontal sync signal and FIELD sync signal from the video signal are separated， then control signal according to the sync signal by DSP and FPGA is generated to control the switching between multiple video channels. Thus， it achieves to make a video processor to monitor different place. Experimental results show that the method can realize video channel switching reliably， and is applied in the video monitoring warning system successfully.
上传时间： 2013-11-09
上传用户：不懂夜的黑
摘 要 瞬态仿真领域的许多工作需要获得可视化数据, 仿真电路不能将输出参数绘制成图形时研究工作将受到很大影响. 而权威电路仿真软件PSpice 在这个方面不尽如人意. 本文提出了一种有效的解决办法: 通过MATLAB 编程搭建一个PSpice 与MATLAB 的数据接口,使PSpice输出数据文件可以导入到MATLAB中绘制图形. 这令我们能够很方便地获得数据的规律以有效地分析仿真结果, 这项技术对于教学和工程实践都有比较实际的帮助.关键词: 瞬态仿真 仿真程序 PSpice MATLAB 可视化数据The Data Transfer from Pspice to MATLABWu hao Ning yuanzhong Liang yingAbstract Many works in the area of transient simulation has shown how a emulator such asPSpice can be interfaced to an control analysis package such as MATLAB to get viewdata. Thepaper describes how such interfaces can be made using the MATLAB programming. The platformas a typical platform will solve the problem that PSpice software sometimes can not draw the datato a picture. It can make us find the rule from numerous data very expediently, so we can analyzethe outcome of the simulation. And it also can be used in the FIELD of education.Keywords Transient Simulation Emulator PSpice MATLAB Viewdata1 引言科学研究和工程应用常需要进行电路仿真 PSpice可进行直流 交流 瞬态等基本电路特性分析 也可进行蒙托卡诺 MC 统计分析 最坏情况 Wcase 分析 优化设计等复杂电路特性分析 它是国际上仿真电路的权威软件 而MATLAB的主要特点有 高效方便的矩阵和数组运算 编程效率高 结构化面向对象 方便的绘图功能 用户使用方便 工具箱功能强大 两者各有着重点 两种软件结合应用 对研究工作有很重要的意义香港理工大学Y. S. LEE 等人首先将PSpice和MATLAB结合 开发了电力电子电路优化用的CAD 程序MATSPICE[6] 将两者相结合的关键在于 如何用MATLAB 获取PSpice的仿真数据 对此参考文献 6 里没有详细叙述 本文着重说明用MATLAB 读取PSpice仿真数据的具体方法本论文利用MATLAB对PSpice仿真出的数据处理绘制出后者无法得到或是效果不好的仿真图形 下面就两者结合使用的例子 进行具体说明
上传时间： 2013-10-20
上传用户：wuchunzhong
Abstract: There are many things to consider when designing a power supply for a FIELD-programmablegate array (FPGA). These include (but are not limited to) the high number of voltage rails, and thediffering requirements for both sequencing/tracking and the voltage ripple limits. This application noteexplains these and other power-supply considerations that an engineer must think through whendesigning a power supply for an FPGA.
上传时间： 2013-11-10
上传用户：iswlkje
