For more than a century, overhead lines have been the most commonly used technology for transmitting electrical energy at all voltage levels, especially on the highest levels. However, in recent years, an increase in both the number and length of HVAC Cables in the transmission networks of different countries like Denmark, Japan or United Kingdom has been observed. At the same time, the construction of offshore wind farms, which are typically connected to the shore through HVAC Cables, increased exponentially.
标签： Electromagnetic Transients Cables Power in
上传时间： 2020-06-06
上传用户：shancjb
Abstract: Nonideal cable dispersive effects can affect system performance. This application note discusses the twomain loss effects related to Cables (skin-effect and dielectric losses), and presents a simple method of modeling thecable for use in standard SPICE simulators.
上传时间： 2014-11-17
上传用户：wxnumen
A frequent requirement in systems involves drivinganalog signals into non-linear or reactive loads. Cables,transformers, actuators, motors and sample-hold circuitsare examples where the ability to drive diffi cult loads isrequired. Although several power buffer amplifi ers areavailable, none have been optimized for driving diffi cultloads.
上传时间： 2014-12-24
上传用户：1109003457
The P82B715 I2C Buffer was designed toextend the range of the local I2C bus out to50 Meters. This application note describesthe results of testing the buffer on severaldifferent types of Cables to determine themaximum operating distances possible. Theresults are summarized in a table for easyreference.
标签： extender P82B715 Using I2C
上传时间： 2014-12-27
上传用户：lou45566
Abstract: This article explains the recent trend in heart-rate and fitness monitors to go wireless toeliminate Cables to allow free movement, and allow convenient data collection without the need to plug intheir devices. It details a typical wireless system, using the MAX1472 crystal-referenced phase-lockedloop (PLL) VHF/UHF transmitter.
标签： Heart-RateFitness Monitors Wireless Go
上传时间： 2013-11-11
上传用户：xiaowei314
Altera recommends the following system configuration: * Pentium II 400 with 512-MB system memory (faster systems give better software performance) * SVGA monitor * CD-ROM drive * One or more of the following I/O ports: - USB port (if using Windows XP or Windows 2000) for USB-Blaster(TM) or MasterBlaster(TM) communications Cables, or APU programming unit - Parallel port for ByteBlasterMV(TM) or ByteBlaster(TM) II download Cables - Serial port for MasterBlaster communications cable * TCP/IP networking protocol installed * Windows 2000, Windows NT 4.0 with Service Pack 3 or later, or Windows XP * Internet Explorer 5.0 or later Memory & Disk Space Requirements USB开发
标签： system configuration recommends following
上传时间： 2015-03-27
上传用户：13188549192
Networking for Dummies 8th Edition ,Written for even the most network-shy novice, this book begins with the most basic of basics and progresses through all the essentials, from Cables, routers and hubs to building a wireless network.英文版 CHM格式
标签： network-shy Networking for Dummies
上传时间： 2015-12-16
上传用户：shus521
The Original USB 2.0 specification released on April 27, 2000 Errata to the USB 2.0 specification as of December 7, 2000 Mini-B connector Engineering Change Notice to the USB 2.0 specification. Pull-up/pull-down Resistors Engineering Change Notice to the USB 2.0 specification. Errata to the USB 2.0 specification as of May 28, 2002 Interface Association Descriptor Engineering Change Notice to the USB 2.0 specification. Rounded Chamfer Engineering Change Notice to the USB 2.0 specification as of October 8, 2003 Unicode Engineering Change Notice to the USB 2.0 specification as of February 21, 2005 Inter-Chip USB Supplement Revision 1.0 as of March 13, 2006 Revision 1.3 of the USB On-The-Go Supplement as of December 5, 2006 Revision 1.01 of the Micro-USB Cables and Connectors Specification as of April 4, 2007 USB 2.0 Link Power Management Addendum Engineering Change Notice to the USB 2.0 specification as of July 16, 2007.
标签： specification 2.0 USB Original
上传时间： 2013-12-31
上传用户：familiarsmile
A new cable fault location method based on wavelet reconstruction is proposed. In this method the difference between the currents of faulty phase and sound phase under the high voltage pulse excitation is used as the measured signal and is decomposed in multi-scale by wavelet transform, then reconstructed in single scale. Comparing with traditional fault location method by travelling wave, the presented method will not be interfered by the reflected wave from the branch joint of Cables or from other positions where the impedances are not matched and not be influenced by fault types, otherwise, the reflected waves can be recognized even the faulty position is near to the measuring terminal, at the same time, the influence of the wave speed uncertainty can be reduced. The correctness of the proposed method is proved by simulation results.
标签： method reconstruction location proposed
上传时间： 2016-02-03
上传用户：maizezhen
The Hardware Book contains misc technical information about computers and other electronic devices. You ll find the pin out to most common (and uncommon) connectors availble, as well as info about how to build Cables.
标签： information electronic computers technical
上传时间： 2013-11-29
上传用户：cc1015285075
