功能：arm7平台的I2c驱动程序，硬件I2C软件包，利用中断方式操作。 * 说明：主程序要配置好I2C总线接口(GPIO、总线时钟)
上传时间： 2014-01-21
上传用户：fhzm5658
TLC549是一种采用8位逐次逼近式工作的A/D转换器。内部包含系统时钟、采样和保持、8位A/D转换器、数据寄存器以及控制逻辑电路。TLC549每25uS重复一次“输入—转换—输出”。器件有两个控制输入：I/O CLOCK和片选（CS）。 内部系统时钟和I/O CLOCK可独立使用。应用电路的设计只需利用I/O时钟启动转换或读出转换结果。当CS为高电平时，DATA OUT处于高阻态且I/O时钟被禁止。
上传时间： 2014-01-17
上传用户：qiaoyue
TI C5409 IIC 接口程序，利用GPIO,自己实现时序
上传时间： 2014-01-10
上传用户：hoperingcong
Hey. This some pid code for the atmega88 that I once used to control a heater. It s purpose is pretty specific, and I only wrote it to work on the mega88, so the code itself won t be too useful. It is a good place to start if you re trying to use or figure out pid though.
标签： control purpose atmega heater
上传时间： 2013-12-19
上传用户：天诚24
IO 驱动 LCD , *** *** *** *** *** *** *** *** FILE NAME: IO_LCD MCU: HT46R22 MASK OPTION: WAKE-UP: PA6,PA7 PULL-HIGH: PA,PB,PC IIC: DISABLE PFD: DISABLE PWM: DISABLE WDT: ENABLE CLRWDT: ONE WDT CLOCK SOURCE: T1 WDT TIME OUT SELECT: WDT CLOCK SOURCE/32768 LVR: DISABLE OSC: CRYSTAL SYSVOLT: 3.0V SYSFRAG: 4000KHZ AUTHOR: RADOME HISTORY: 2005.08.
上传时间： 2014-12-21
上传用户：watch100
本文研究了在目前流行的嵌入式微控制器ARM9(Samsung 的 S3C2410)上硬件测试的方法。分析了在嵌入式Linux基础上开发测试程序的基本方法，解决了在S3C2410开发板测试GPIO、中断、串口和RTC时钟过程中的重点和难点问题。
标签： Samsung S3C2410 Linux ARM9
上传时间： 2015-12-08
上传用户：semi1981
To increase simulation speed, ModelSim® can apply a variety of optimizations to your design. These include, but are not limited to, mergingprocesses, pulling constants out of loops, clock suppression, and signal collapsing. You control the level of optimization by specifying certain switches when you invoke the compiler.
标签： optimizations simulation ModelSim increase
上传时间： 2013-12-25
上传用户：pkkkkp
Welcome to the software files for the ADS8361 to TMS320F2812! There are two project files in each of the folders McBSP, SPI and Both. Mode II and IV are explored using the McBSP port alone, as well as the SPI port. These projects are located in the SPI and McBSP folders. Modes I and III are explored using both McBSP and SPI. In Mode I, the M0 and M1 pins are controlled by use of the jumper on the evaluation module. A0 is controlled by the DX pin of the McBSP port. In Mode III, the A0, M0 and M1 pins are controlled via GPIO functions of PortF. The "SRC", "CMD" and "INCLUDE" files in the archive are from "C28x Peripheral Examples in C" (document # SPRC097). If you have questions about this or other Data Converter products, feel free to e-mail us at:
标签： files the software Welcome
上传时间： 2015-12-16
上传用户：lixinxiang
RDC R2886 Ethernet hub功能 源码,paradigm c++上运行测试，模拟hub运行，RJ45-1 IN ,RJ45-2 OUT
标签： Ethernet paradigm R2886 RDC
上传时间： 2015-12-20
上传用户：jing911003
使用周立功的ARM2131，进行GPIO的简单控制，完成流水灯的控制。
上传时间： 2015-12-20
上传用户：chfanjiang
