首先研究CAN总线和SAE J1939协议，提出一种基于MC9S12HZ256微控制器的总线式汽车数字仪表解决方案。详细介绍SAE J1939协议的报文帧格式及应用层协议中发动机相关参数的定义，以及步进电机及其驱动和车速信号的处理方法。该数字仪表系统硬件平台由微处理器和信号采集和信息处理及显示等模块组成。软件设计部分编程实现了对CAN总线和各传感器数据的读取、处理。该系统能够实时反映车辆工况。 Abstract: In this paper，CAN bus and SAE J1939protocol are researched，and a vehicle digital instrument solution based on MC9S12HZ256MCU is proposed.The message frame format and some engine-related parameters’definition in SAE J1939application layer protocol are introduced in detail.Stepper motor and its driver，the methods of speed signal process-ing are also introduced.The hardware platform of vehicle digital instrument is composed by MCU，signal acquisition mod-ule，and signal processing and displaying module.Data receiving and processing from CAN bus and sensors are accom-plished by programming，and vehicle condition can be reflected in real-time.
上传时间： 2013-10-20
上传用户：huannan88
介绍一种基于CAN总线的牵引变电站自动化系统通讯规约的设计，CAN通讯规约采用标准帧，报文采用主动发送和发送查询两种处理形式。该设计在城市轻轨与地铁牵引变电站中的应用表明：可实现间隔层和通讯处理层的数据快速、可靠的交换，提高牵引变电站的安全性和稳定性 。 Abstract: This paper firstly presents a kind of design dealing with communicational protocol to the traction substation automation system based on CAN bus,and then comes up with the ideas that all frames of CAN communicational protocol should adopt the standard frame,and that messages be processed by two ways:sending initiatively and sending quiries.Subway and light rail application shows that the use of the CAN bus is possible to exchange data quickly and reliably between the layers of the middle and the communicational processing,hence to improve the safety and stability of traction substations.
上传时间： 2013-11-07
上传用户：bs2005
详细介绍了PCI9052接口器件的功能、结构和使用方法，并结合实际给出了基于PCI9052器件开发PCI总线接口卡的应用实例。 Abstract: The main functions,structures and usage of PCI9052inferface chip are introduced in detail in this paper.And an application example of designing PCI bus interface card based on PCI9052is proposed in this paper.
上传时间： 2013-10-16
上传用户：togetsomething
介绍基于ISA总线与KH-9300的数据采集板卡的设置，详细说明8254定时计数器及8259中断控制器的结构特点、工作方式、控制字等，探讨中断类型、中断处理程序、中断矢量表及其填写。重点讲述使用TorboC编写中断服务程序的方法，应注意的主要问题及程序测试的结果。 Abstract: The settings of KH-9300 data acquisition board based on the ISA bus is introduced,the structural characteristics,working methods,control characters of the timing counter 8254 and interruptioncontroller 8259 are explained in detail.The interruption type,interrupt handling programs,interruption vector table and its filling also are discussed.Further,great emphasis is put on the method of interrupt service program compiled by Torbo C,the main issues that should be noted,and the results of program testing.
上传时间： 2013-11-14
上传用户：qq527891923
摘要：介绍了基于IIS总线嵌入式音频设备硬件体系结构及其Linux驱动设计在音频驱动设计综合使用了DMA、分段多缓存区和内存映射技术以提高系统性能满足音频实时性要求。 关键词：音频设备驱动 IIS总线 嵌入式Linux DMA 内存映射
上传时间： 2013-10-13
上传用户：Aeray
在开放式数控系统结构模型的基础上，研究了基于ISA总线的DSP通信控制原理。采用中断方式完成了PC机和DSP之间的通信。介绍了以DriverWorks为工具开发ISA设备WDM驱动程序的方法，探讨了中断处理、驱动程序与应用程序之间的通信,简要说明了驱动程序的安装与调试。通过调试,系统设计运行稳定。 Abstract: The ISA bus and DSP correspondence control principle is investigated in the basis of the existing open architecture numerical control system.The interrupt method is used to realize the communication between PC and DSP based on the ISA bus.The methods of WDM driver exploitation for ISA device using Driver Works are introduced.The main process of driver program and the keys such as handle interrupt and the communication between the drivers and application are presented.And how to debug and install the drive is explained.
上传时间： 2013-11-04
上传用户：kang1923
针对目前采用的热敏电阻测量方法，提出了采用单总线数字式温度传感器DS18B20和单片机组成的新型温度测量仪。介绍DS18B20的结构和工作原理，以及单总线工作原理，给出了由Mega8单片机和DS18B20构成的单总线温度测量仪的硬件电路及软件流程图。经试验基于单总线器件DS18B20的温度测量仪，具有测量准确、测温范围宽、体积小、控制方便等优点。 Abstract: This paper brings forward a new temperature meter composed of 1-Wire temperature sensor DS18B20 and MCU which has advantage of the thermistor. In the article, the DS18B20＇s structure and controlling principles are introduced and hardware circuit and software diagram of the temperature meter are given.After been tested,the temperature meter has the advantages of accurate measurement, wide temperature range, small volume and convenient controlling.
上传时间： 2013-10-31
上传用户：hzy5825468
对于沥青混凝土摊铺机自动找平控制系统来说，数字式控制系统的研制是目前的一个方向。介绍了一种基于CAN总线的数字式自动找平控制系统。该系统以CAN总线作为通信方式，PWM控制信号通过C8051F040单片机内部PCA可编程计数器阵列产生，并具有结构简单、信号稳定、实时性强、易扩展的特点。通过硬件实现和系统运行达到了比较理想的控制效果，验证了系统的可行性。 Abstract: A digital auto-leveling control system based on CAN Bus is introduced.It uses CAN Bus as the method of communication and creates PWM signals by programmable counter array in C8051F040 microcontroller. The system is simple, stable, real-time and expansive.
上传时间： 2013-10-09
上传用户：ligi201200
设计了一款基于Avalon总线的8051MCU IP核。它支持MCS-51指令集，优化内部的结构，通过采用流水线技术、指令映射技术、指令预取技术、微代码技术等极大的提高了IP核的工作速度，使IP核在100MHz时钟下，能够单周期执行一条指令。本设计使用Modelsim软件完成了功能仿真和时序仿真，并在以Altera 公司的Cyclone II FPGA芯片为核心的DE2开发板上完成了硬件验证。
上传时间： 2013-11-02
上传用户：gundan
一、用途D485C型单片机用TTL/RS-485/RS-422转换器用于将单片机的RS-232串行口（TTL电平）转换成RS-485或者RS-422电平，可以将单片机串行口的通信距离延长至1200m以上（9600bps时），可以用于单片机之间、单片机与PC机之间构成远程多机通信网络。二、硬件安装D485C型转换器外形为DB-9/DB-9转接盒大小，其中DB-9（孔座）一端接单片机的RS-232串行口（只用到RXD、TXD、GND）以及+5V电源。DB-9针座为转换后的RS-485、RS-422信号。三、软件说明本产品均无需任何初始化设置！无须收发转换控制信号！只用到单片机RS-232串行口的RXD（收）、TXD（发）、GND（地）信号，加上独有的内部零延时自动收发转换技术，确保适合所有软件！四、性能说明D485C型转换器需外接5V电源，最高速率115.2Kbps。外接电源要求：电压5V±0.5V，电流>10mA。五、D485C的外形图、引脚分配D485C作为TTL/RS-485转换器（注意跳线短接位置）
上传时间： 2013-12-26
上传用户：独孤求源
