When a system designer specifies a nonisolated dc/dc powermodule, considering the needed input voltage range isequally as important as considering the required performanceattributes and features. Generally, nonisolated moduleshave either a narrow or a wide input voltage range. Narrowinputmodules typically have a nominal input voltage of3.3, 5, or 12 V. For systems that operate from a tightlyregulated input bus—such as those that do not use batterybackup—a narrow-input module is often adequate sincethe input remains fairly stable.Offering greater flexibility, wide-input modules operatewithin a range of 7 to 36 V, which includes the popular12- or 24-V industrial bus. This enables a single module tobe used for generating multiple voltages. These modulesare ideal for industrial controls, HVAC systems, vehicles,medical instrumentation, and other applications that usea loosely regulated distribution bus. In addition, systemspowered by a rectifier/battery charger with lead-acidbattery backup almost always require wide-input modules.System designers who choose power supplies may wantto take a close look at the latest generation of wide-inputdc/dc modules.
标签： Wide-input modules offer dc
上传时间： 2014-12-24
上传用户：dragonhaixm
上传时间： 2013-11-17
上传用户：yuanyuan123
The latest generation of Texas Instruments (TI) boardmountedpower modules utilizes a pin interconnect technologythat improves surface-mount manufacturability.These modules are produced as a double-sided surfacemount(DSSMT) subassembly, yielding a case-less constructionwith subcomponents located on both sides of theprinted circuit board (PCB). Products produced in theDSSMT outline use the latest high-efficiency topologiesand magnetic-component packaging. This providescustomers with a high-efficiency, ready-to-use switchingpower module in a compact, space-saving package. Bothnonisolated point-of-load (POL) switching regulators andthe isolated dc/dc converter modules are being producedin the DSSMT outline.TI’s plug-in power product line offers power modules inboth through-hole and surface-mount packages. The surfacemountmodules produced in the DSSMT outline use asolid copper interconnect with an integral solder ball fortheir
上传时间： 2013-10-10
上传用户：1184599859
超高压发生器输出几十千伏超高压、应用负粒子、点火、臭氧。简易超高压发生器，图1-1的电路可输出几十千伏超高压。当接通电源时，电源经R向C2充电至2CTS导通，即触发SCR导通。原来C被电源充满的电荷立即经SCR放电，升压变压器T次级感应高压电。当用汽车点火线圈作升压器，电容C1容量为0.1uF时，空气火花间长度为12mm。空气的绝缘度是3KV/mm，所以对应的高压是36KV。本电路耗电约为1W。制作时请注意安全！
上传时间： 2014-12-24
上传用户：wli25203
International reference list 02/2004International referenceJ.JaatinenCompany CountryBerlin GermanyDeutsche Flugsicherung GermanyFrankfurt GermanyGuangzhou ChinaHamburg GermanyHelsinki-Vantaa FinlandKuala Lumpur - Sepang MalaysiaZürich Switzerland
标签： Quality Energy Power Manag
上传时间： 2013-10-30
上传用户：1184599859
VIPER22A的内部结构可知,它与其它开关电源存在一些不同。开机后,300V的直流电压从DRAIN(漏极)脚进入集成电路,经整流和稳压后供给开关电源IC工作,从而使这个电路工作时不需要外接启动电阻。即使Vdd供电电路不正常,电源电路的振荡电路仍能起振,而且电路有输出电压。用这种专用电源IC的DVD机电源有故障时,故障现象和其他开关电源的故障有所不同,其他开关电源通常无Vdd时,电源电路中的振荡电路不起振,会出现无输出的故障现象。
上传时间： 2013-11-09
上传用户：1039312764
前言尊敬的客户，非常感谢您使用阳光电源有限公司的光伏并网逆变器产品。本公司有着多年光伏并网发电装置的研制经验，我们希望本产品能满足您的需求，同时期望您能对产品的性能和功能提出更多的意见。
上传时间： 2013-10-23
上传用户：kqc13037348641
电源的工作原理其实就是D类功率放大器，即串联型电压开关放大器，如图1．36所示。
上传时间： 2013-11-08
上传用户：ks201314
幻象电源在专业音响领域几乎是无处不在的。MR-PRO内含有测试幻象电源电压的功能，可以持续监测和显示幻象电源输出端的直流电压。MR-PRO也可以接到调音台的麦克风输入端，并持续监测满载或空载时的实际有效幻象电源电压。本应用指南详细描述了如何按照IEC1938标准对幻象电源进行量测。
上传时间： 2013-10-22
上传用户：rocketrevenge
摘要:在北京正负电子对撞机二期改造工程(BEPC2),磁铁电源系统大量使用了电流型直流传感器(DCCT)作为电源的反馈和回采器件.
上传时间： 2013-10-19
上传用户：Amygdala
